TFA Log32 TH Manual

TFA Måling Log32 TH

Læs nedenfor 📖 manual på dansk for TFA Log32 TH (2 sider) i kategorien Måling. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

1.2 General advice

• Check if the contents of the package is umdamaged and complete.

• Remove the protection foil above the start button and the two LEDs.

• For cleaning the instrument please do not use an abrasive cleaner only a dry or

wet piece of soft cloth. Do not allow any liquid to the interior of the device.

• Please store the measuring instrument in a dry and clean place.

• Avoid any force like shocks or pressure to the instrument.

• No responsibility is taken for irregular or incomplete measuring values and their

results, the liability for subsequent damages is excluded!

• Do not use the device in an environment hotter than 85°C!

The lithium battery may explode!

• Do not expose the unsit to microwave radiantion. The lithium battery may explode!

1.4 Scope of delivery and usage

LOG32TH/LOG32T/LOG32THP series loggers are suitable for recording, alarm

tracking, and display of temperature, humidity*, dew point* (*only LOG32TH/THP) and

barometric pressure (only LOG32THP) measurements. Areas of application include

the monitoring of storage and transport conditions or other temperature, moisture

and / or pressure-sensitive processes. The logger has a built-in USB port can be

connected without cables to all Windows PCs. The USB port is protected by a

transparent plastic cap. The green LED ashes every 30 seconds during recording.

The red LED is used to display limit alarms or status messages (battery change ...

etc.). The logger also has an internal buzzer that supports the user interface.

1. Start button, 2. LED green, 3. LED red, 4. battery case, 5. USB-connector, 6. USB-

cover, 7. wall holder, 8. Slits ... this is where the sensor is located, 9. protective foil

1.3 Overview see Fig.A

Press button for 2 seconds,

beeper sounds for 1 second

LED lights green for 2 sconds - logging

has started!

LED blinks green every 30 sec.

2. First Start & Begin Recording

1.6 Ready to use

The logger is already preset (see 5 default settings) and ready for start. It can be used

immediately without any software!

1.5 For your safety

This product is exclusively intended for the eld of application described above.

It should only be used as described within these instructions.

Unauthorized repairs, modications or changes to the product are prohibited.

2.1 Restart recording

see 2. The logger is started by default by button and stopped by USB port plug-in.

The measured values are plotted automatically to the PDF le.

NOTE: When you restart the existing PDF le is overwritten.

Important! Always secure the generated PDF les on your PC.

3. Stop recording / Create PDF

Connect logger to USB port.

Beeper sounds for 1 second. The

recording stops.

LED blinks green until result PDF is

created (can take up to 40 seconds).

Beeper sounds and LED stays green.

Logger is shown as removeable drive

LOG32TH/LOG32T/ LOG32THP.

View PDF and save.

PDF will be overwritten with next

log start!

5. Standard settings / Factory settings

Note the following default settings of the data logger before rst use. By using the

LogConnect* software, the setting parameter can easily be changed:

Interval: 5 min. LOG32TH/ LOG32THP, 15 min. LOG32T

Start possible by: Key press

Stop possible by: USB connect

Alarm: off

4. Description of PDF result le (see Fig. B)

Filename: e.g.

LOG32TH_14010001_2014_06_12T092900.DBF

LOG32TH: Device

14010001: Serial

2014_06_12: Start of recording (date)

T092900: time: (hhmmss)

Description: Log run info, edit with LogConnect* software

Conguration: preset parameters

Summary: Overview of measurement results

Graphics: Diagram of measured values

Signature: Sign PDF if required

:Measurement OK :Measurement failed

Download free LogConnect software:

www.dostmann-electronic.de/home.html ->Downloads ->

Software/<your logger>/Software/LogConnect_XXX.zip

(XXX choose latest version)

GB 1. Introduction

Thank you very much for purchasing one of our products. Before opera-

ting the data logger please read this manual carefully. You will get useful

information for understanding all functions.

Schnellstart mit Standardeinstellungen

Aufzeichnung starten.

Gedrückt halten bis

Signalton ertönt.

LED blinkt grün

(alle 30 Sek.)

Logger in USB port warten PDF anschauen

und sichern

1. 2.

3. 4. 5.

6. Battery replacement

Twist rear cap (about 10°),

the battery lid opens.

Remove empty battery and insert

new battery like shown.

Battery change ok:

both LEDs light for 1second, beep sounds.

7. Alarm signals

Logger in record mode

Beeper sounds once each 30 seconds for

1 second, red LED blinks each

3 seconds - measured values exceeds

selected measurement range

(not with standard settings).

Alarm limits can be changed using

LogConnect* software.

Technical changes, any errors and misprints reserved. Stand08_CHB2112

Logger in standby mode (not in record mode)

Red LED blinks once each 4 seconds.

Replace battery.

Red LED blinks twice or more

each 4 sconds. Hardware fault!

Download free LogConnect software:

www.dostmann-electronic.de/home.html ->Downloads ->Software/<your logger>/

Software/LogConnect_XXX.zip (XXX choose latest version)

NOTE: Check Logger status: Press start button for appr. 1 second. If the green

LED ashes twice the logger is recording! This procedure can be done as often as

you want.

1.1 Delivery contents

• Data logger LOG32 • Wall holder • Battery 3,6 Volt

• USB protection cap • 2x screws and dowels (already inserted)

ATTENTION! Please observe our battery recommendation strictly. Use only the battery

type LS 14250 3.6 volt of the manufacturer SAFT or DYNAMIS Lithium Batt. LI-110 1/2

AA/S, respectively only batteries authorized by the manufacturer.

5005-0170 / 5005-0172 / 5005-0173

LOG LOG32T /32TH /

LOG32THP

Bedienungsanleitung

Operating Instructions

Datenlogger für Temperatur, Feuchte und Druck* **

Data logger for

temperature, humidity

* ** and pressure

DOSTMANN electronic GmbH · Waldenbergweg 3b

D-97877 Wertheim · www.dostmann-electronic.de

*nur LOG32TH/LOG32THP / *only LOG32TH/LOG32THP

**nur LOG32THP / **only LOG32THP

9. Marking

only LOG32T

CE-conformity, EN 12830, EN 13485, Suitability for storage (S) and transportation

(T) for food storage and distribution (C), Accuracy classication 1 (-30..+70°C),

according to EN 13486 we recommend a recalibration once per year.

This sign certies that the product meets the requirements of the

EEC directive and has been tested according to the specied test methods.

8. Waste disposal

This product and its packaging have been manufactured using high-grade materials and components which can be

recycled and reused. This reduces waste and protects the environment. Dispose of the packaging in an environ-

mentally friendly manner using the collection systems that have been set up.

Disposal of the electrical device: Remove non-permanently installed batteries and rechargeable batteries

from the device and dispose of them separately.

This product is labelled in accordance with the EU Waste Electrical and Electronic Equipment Directive

(WEEE). This product must not be disposed of in ordinary household waste. As a consumer, you are

required to take end-of-life devices to a designated collection point for the disposal of electrical and electronic

equipment, in order to ensure environmentally-compatible disposal. The return service is free of charge.

Observe the current regulations in place!

Disposal of the batteries: Batteries and rechargeable batteries must never be disposed of with household

waste. They contain pollutants such as heavy metals, which can be harmful to the environment and

human health if disposed of improperly, and valuable raw materials such as iron, zinc, manganese or

nickel that can be recovered from waste. As a consumer, you are legally obliged to hand in used batteries and

rechargeable batteries for environmentally friendly disposal at retailers or appropriate collection points in

accordance with national or local regulations. The return service is free of charge. You can obtain addresses of

suitable collection points from your city council or local authority. The names for the heavy metals contained are:

Cd = cadmium, Hg = mercury, Pb = lead. Reduce the generation of waste from batteries by using batteries with

a longer lifespan or suitable rechargeable batteries. Avoid littering the environment and do not leave batteries or

battery-containing electrical and electronic devices lying around carelessly. The separate collection and recycling

of batteries and rechargeable batteries make an important contribution to relieving the impact on the environment

and avoiding health risks.

WARNING! Damage to the environment and health through incorrect disposal of the batteries!

WARNING! Batteries containing lithium can explode

Batteries and rechargeable batteries containing lithium (Li=lithium) present a high risk of re and explosion due to

heat or mechanical damage with potentially serious consequences for people and the environment. Pay particular

attention to correct disposal.

Produkt Specifikationer

Mærke:	TFA
Kategori:	Måling
Model:	Log32 TH
Type:	Elektronisk hygrometer
Produktfarve:	Sort
Skærmtype:	Digital
Termometer:	Ja
Formål:	Indendørs
Temperatur, måleenheder:	°C
Temperatur måleområde:	0 - 0.5 °C