Thule RodVault 2 870002 Manual

Thule Ikke kategoriseret RodVault 2 870002

Læs nedenfor 📖 manual på dansk for Thule RodVault 2 870002 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
1506-7389_02
PREPARATION
Step 1:
Unpackage Thule Rod Vault and place both sections
on a scratch free surface with the reel housing facing
up, and the nose cone with the rivets facing up
Remove the parts from the internal packaging box
and lay them out. Cross reference with "provided"
list from above
Before you begin to assemble: remove the 2" bolts
from the tube clamps (FIGURE #1)
Step 2:
Place the threaded tube clamps underneath the tubes,
then place the non-threaded piece directly on top
Slide a lock washer, then a flat washer onto the
partially threaded 2.5" (2 or 4) king bolts
Insert king bolt up through the mounting clamp &
clamp cover (x2 or x4) using a ¼ inch allen wrench,
screw king bolts into the tube clamps and leave them
loose enough so that the tube clamps can still slide
back and forth (FIGURE #2)
Step 3:
Loosen coupler screws with 4mm allen wrench
Connect the nose cone & reel house sections, making
sure tubes are flush and meet at the center the
couplers, then tighten
EN
PROVIDED
(2) keys
(2 or 4) mounting clamps & (2 or 4) clamp covers
(2 or 4) feet
(2 or 4) 2.5" king bolts - partially threaded
(2 or 4) lock washers & (2 or 4) flat washers
(2 or 4) couplers with a total of 12 or 24 screws
(4 or 8) 2" bolts fully threaded with washers (2 or 4 of
these are located in the tube clamps during shipping,
you will need to remove them before assembly)
(2 or 4) tube clamp sets composed of one threaded
piece and one not threaded piece
¼ inch allen wrench (for 2.5" partially threaded bolts &
2" fully threaded bolts)
4mm allen wrench (for the coupler screws)
Thule Xsporter Adapter (4 or 8 2.5" king bolts)
MEASURE & SET
Gently set the Thule Rod Vault on top of your vehicle
and adjust the (2 or 4) tube clamps to sit on your
crossbars (ideally, one tube clamp on each side of the
couplers, but not mandatory)
Make sure the reel housing is far enough forward so
that you can open your rear window or hatch on your
vehicle (some vehicles like Toyota 4runners, may need
a “lift kit" [available separately] so that the reel housing
clears the roof)
Once adjusted, remove the rod vault and tighten down
the king bolts into place
INSTALL ON YOUR VEHICLE
Note: If mounting to Thule Xsporter use 2.5" king bolts
instead of 2" bolts on mounting clamp assemblies
Place Thule Rod Vault on top of vehicle ensuring that it
is straight, twist the clamp cover on the mounting clamp
to expose the bolt holes
Place one mounting clamp foot under each mounting
clamp and insert (2) 2" bolts with washers and tighten
(FIGURE #3). DO NOT OVERTIGHTEN, as feet may
break
Rotate top clamp cover so that the “lock holes" are
aligned (this provides an option to padlock your rod
vault to your vehicle)
Always check tightness of all bolts before each trip to
ensure the rod vault is secure. Do not overtighten
Installation
instructions
Thule RodVault
870002 2 fly rods
870004 4 fly rods


Produkt Specifikationer

Mærke: Thule
Kategori: Ikke kategoriseret
Model: RodVault 2 870002

Har du brug for hjælp?

Hvis du har brug for hjælp til Thule RodVault 2 870002 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Thule Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024