TP-Link Omada EAP773 Manual
TP-Link
Access Point
Omada EAP773
Læs nedenfor 📖 manual på dansk for TP-Link Omada EAP773 (2 sider) i kategorien Access Point. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
Quick Installation Guide
Wireless Access Point
Note: EAP650 is used as an example throughout the Guide. Images may dier from your actual product.
Hardware Overview
1
RESET
With the device powered on, press and hold the button for about 5 seconds until the LED flashes quickly. Then
release the button. The device will restore to factory default settings.
Ethernet Port: ETH (PoE)
The port is used to connect to a router or a switch to transmit data, or to a PSE (Power Sourcing Equipment),
such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable.
Note: For EAPs with 10Gbps port, if you use a CAT5E cable, the 10Gbps link of the Ethernet port is less than 55m. To achieve a longer
transmission distance, use a shielded CAT6A cable.
Power Port
Plug one end of the power adapter to this port and the other end to a standard electrical wall outlet to power the
EAP.
Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specications or
datasheet. For power supply specications, refer to the product label.
Self-tapping ScrewsPlastic Wall Anchors
1
Remove the ceiling tile.
Note: Make sure that the ceiling tile is larger than the EAP.
Wing NutsWashers Pan-head Screws
The EAP can be mounted to the ceiling, the wall, or in a junction box, using the screws in the
package. Choose the appropriate mounting and installation steps below.
Note: This product requires heat dissipation through the metal bracket during use, please be
careful not to touch the metal bracket in the heat dissipation.
Hardware Installation
2
2
Insert the plastic wall anchors into the holes.
Front Panel
Rear Panel
Option 1: Ceiling Mounting
Option 2: Wall Mounting
5
Connect the Ethernet cable to the Ethernet port.
Please pay attention to the triangle sign. Attach
the EAP to the mounting bracket, then rotate it
until it locks into place, as shown on the left.
2
Place the mounting bracket in the center of the
ceiling tile. Mark positions for the screw holes
and a location for the Ethernet cable hole.
Drill holes for the screws and a hole for the
Ethernet cable at the marked positions.
3
Secure the mounting bracket to the ceiling tile
using pan-head screws, washers, and wing nuts,
as shown on the left.
5
Attach the EAP to the mounting bracket by
rotating it until it locks into place, as shown on
the left.
2
Connect the Ethernet cable to the Ethernet
port on the EAP.
3
Attach the EAP to the mounting bracket by
rotating it until it locks into place, as shown on
the left.
Setup with videos
Visit https://www.tp-link.com/support/setup-video/ or scan the QR code
to search for the setup video of your product model.
4
Feed the Ethernet cable through the hole and
set the ceiling tile back into place.
3
Secure the mounting bracket to the wall by
driving the self-tapping screws into the
anchors. Make sure that the shoulders of the
mounting bracket are on the outside.
1
If your Ethernet cable feeds through the wall,
position the mounting bracket below the cable
hole. Mark positions for the screw holes and
drill holes at the marked positions.
Φ 7.6 mm (19/64 in)
Option 2: Wall MountingOption 1: Ceiling Mounting Option 3: Junction Box Mounting
Blue On:
Working normally/Initializing. For EAPs with dual-color LED: Normal power supply
Orange On:
For EAPs with dual-color LED: Low power supply
Flash: • Flash twice:
Initialization is completed.
• Flash quickly:
The EAP is resetting, or the Omada controller is locating the device*.
• Flash once per second:
The EAP is upgrading.
• Flash Slowly:
The EAP is in the isolated state.
LED Indicator
Off:
Working abnormally/Power o/LED is turned o.
* When the Locate feature is activated in the Omada controller, the LED ashes quickly to locate and identify the
device. The LED will ash for 10 minutes. You can disable the feature manually to stop it from ashing.
Option 3: Junction Box Mounting
Prepare the cables and the junction box in advance. Ensure that the mounting holes align
to your junction box.
Route the cables through the square cable
hole on the mounting bracket, and secure the
mounting bracket to the junction box using
screws.
1
The EAP can be powered via a power adapter or a PSE device (such as a PoE switch) which
complies with Power Source Class 2 ( PS2) or Limited Power Source (LPS) of IEC 62368-1.
Option 1: Via PoE Switch
Option 2: Via Power Adapter
Plug one end of the power adapter into the power port of the EAP and the other end to a
standard electrical wall outlet.
Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specications or
datasheet. For power supply specications, refer to the product label.
Power Supply
3
Switch
Power Adapter
PoE Switch
Connect an Ethernet cable from the PoE switch to the Ethernet port.
Note: For PoE power supply specications, refer to the product label.
*Compatible wall junctions:
©2023 TP-Link 7106510781 REV1.5.1
4
Connect the Ethernet cable to the Ethernet
port on the EAP.
Φ 25 mm (63/64 in)
Φ 4 mm (5/32 in)
Produkt Specifikationer
Mærke: | TP-Link |
Kategori: | Access Point |
Model: | Omada EAP773 |
Har du brug for hjælp?
Hvis du har brug for hjælp til TP-Link Omada EAP773 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Access Point TP-Link Manualer
11 September 2024
10 September 2024
10 September 2024
2 September 2024
2 September 2024
1 September 2024
1 September 2024
1 September 2024
25 August 2024
20 Juli 2024
Access Point Manualer
- Access Point Bosch
- Access Point Aruba
- Access Point Netis
- Access Point Moog
- Access Point HP
- Access Point D-Link
- Access Point Asus
- Access Point Planet
- Access Point Belkin
- Access Point Edimax
- Access Point Black Box
- Access Point DataVideo
- Access Point TRENDnet
- Access Point Buffalo
- Access Point Linksys
- Access Point Cisco
- Access Point Netgear
- Access Point Totolink
- Access Point Digitus
- Access Point Zebra
- Access Point Techly
- Access Point Dell
- Access Point Alcatel-Lucent
- Access Point LevelOne
- Access Point ZyXEL
- Access Point Fortinet
- Access Point Tenda
- Access Point LigoWave
- Access Point EQ3
- Access Point Ubiquiti Networks
- Access Point EnGenius
- Access Point Devolo
- Access Point Grandstream
- Access Point Renkforce
- Access Point Mikrotik
- Access Point Amer Networks
- Access Point Mercku
- Access Point StarTech.com
- Access Point Crestron
- Access Point Lancom
- Access Point Sitecom
- Access Point Intellinet
- Access Point Steren
- Access Point Media-Tech
- Access Point Moxa
- Access Point Allnet
- Access Point Airlive
- Access Point Hawking Technologies
- Access Point INCA
- Access Point Advantech
- Access Point Silex
- Access Point SMC
- Access Point Cambium Networks
- Access Point CradlePoint
- Access Point FlyingVoice
- Access Point Extreme Networks
- Access Point Aerohive
- Access Point WatchGuard
- Access Point NUVO
- Access Point Cudy
- Access Point Mach Power
- Access Point Syscom
- Access Point Bintec-elmeg
- Access Point Brocade
- Access Point ICC
- Access Point Insteon
- Access Point Mojo
- Access Point Luxul
Nyeste Access Point Manualer
17 September 2024
14 September 2024
13 September 2024
13 September 2024
11 September 2024
11 September 2024
11 September 2024
11 September 2024
11 September 2024
11 September 2024