TP-Link TL-SG116P Manual

TP-Link Bryter TL-SG116P

Læs nedenfor 📖 manual på dansk for TP-Link TL-SG116P (4 sider) i kategorien Bryter. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
Connection
© 2023 TP-Link 7106510236 REV4.2.1
Installation Guide
5/6/16-Port Gigabit Desktop PoE Switch
LED Explanation
Note: For simplicity, we will take TL-SG1005P for example throughout this Guide.
Note:
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. TL-SG1005LP can supply up to 30 W for each PoE port and 40 W for all PoE ports.
3. TL-SG1005P can supply up to 30 W for each PoE port and 65 W for all PoE ports.
4. TL-SG1006PP can supply up to 60 W for port 1, 30W for other single PoE port, and 64 W
for all PoE ports.
5. TL-SG116P can supply up to 30 W for each PoE port and 120 W for all PoE ports.
DC Power Adapter
AC Power Cord
IP Camera AP IP Phone
Router
LAN Port WAN Port
Internet
Ethernet Ports (1-5)
PoE Ports (1-4)
Power
On: Power on
O: Power o
Power
Link/Act and PoE Status
On: Providing PoE power
Flashing: Current-overload/Short-circuit
O: Not providing PoE power
On (Green): Connected to a 1000 Mbps
device
On (Yellow): Connected to a 10/100
Mbps device
Flashing: Transmitting/receiving data
O: No device is connected to the
corresponding port.
PoE MAX
PoE Max
TL-SG1005LP
On: 33 W ≤ Total power supply < 40 W
Flashing: Total power supply ≥ 40 W
O: Total power supply < 33 W
TL-SG1005P
On: 58 W ≤ Total power supply < 65 W
Flashing: Total power supply ≥ 65 W
O: Total power supply < 58W
TL-SG116P
On: Total power supply ≥ 113 W
Flashing: Total power supply ≥ 113 W and
lasts for more than 2 minutes
O: Total power supply < 113W
PoE Devices
Switches Explanation
Priority (for TL-SG116P)
O: All the ports transmit data with the same priority.
On: The corresponding ports transmit data with a higher priority than other ports. When congestion
occurs, packets which are transmitted by the ports with a higher priority occupy the whole bandwidth.
Isolation (for TL-SG116P)
O: Ports can transmit data with each other.
On: The corresponding ports cannot transmit data with other downlink ports. They can transmit data
only with the uplink ports (ports 15-16 of TL-SG116P).
Extend (for TL-SG1005P/TL-SG1006PP/TL-SG116P)
O: The corresponding ports run at 10/100/1000 Mbps and support PoE power supply up to 100 m away.
On: The corresponding ports run at 10 Mbps and support PoE power supply up to 250 m away.
Recovery (for TL-SG1005P/TL-SG1006PP/TL-SG116P)
O: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD). When the switch
nds that the PD works abnormally, the switch will reboot it.
Note: The numbers in brackets indicate the ports where the feature takes eect. For example, when Extend(1-4) is toggled to On, the Extend mode will be enabled for ports 1-4.
TL-SG1006PP
On: 57 W ≤ Total power supply < 64 W
Flashing: Total power supply ≥ 64 W
O: Total power supply < 57W


Produkt Specifikationer

Mærke: TP-Link
Kategori: Bryter
Model: TL-SG116P
Vekselstrømsindgangsspænding: 220 V
Vekselstrømsindgangsfrekvens: 50 Hz
Bredde: 286 mm
Dybde: 111.7 mm
Højde: 25.4 mm
Produktfarve: Sort
Pakkevægt: 2000 g
Pakkedybde: 434 mm
Pakkebredde: 227 mm
Pakkehøjde: 70 mm
Opbevaringstemperatur (T-T): -40 - 70 °C
Relativ luftfugtighed ved drift (H-H): 10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H): 5 - 90 %
Strømforbrug (typisk): 11.72 W
Driftstemperatur (T-T): 0 - 40 °C
Husmateriale: Metal
Hurtig start guide: Ja
Strømforbrug (maks.): 144.28 W
Netværksstandarder: IEEE 802.1Q, IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u
Servicekvalitet support (QoS): Ja
LED-indikatorer: Ja
Kan monteres på væggen: Ja
DC indgangsspænding: 9 V
Indgangsstrøm: 0.6 A
Fuld duplex: Ja
Strøm over Ethernet (PoE): Ingen
Switch-type: Ikke administreret
Auto MDI/MDI-X: Ja
VLAN understøttelse: Ja
Flowkontrol support: Ja
Port-spejlning: Ja
Antal VLAN'er: 32
Link aggregering: Ja
Kobber ethernet kabelteknologi: 10BASE-T, 100BASE-TX, 1000BASE-T
Broadcast stormkontrol: Ja
Vituelle LAN funktioner: Protocol-based VLAN, Tagged VLAN
Basis omskiftning RJ-45 Ethernet porte, antal: 16
Basis omskiftning RJ-45 Ethernet porttype: Gigabit Ethernet (10/100/1000)
IGMP snooping: Ja
Loop beskyttelse: Ja
Opbevar-og-frem: Ja
MAC adresselabel: 8000 entries
Switch kapacitet: 32 Gbit/sek.
Antal køer: 4
Jumbo Frames support: Ja
Jumbo rammer: 9000
Varmeafgivelse: 490.55 BUT/t
Gigabit Ethernet (kobber) porte, antal: 16
Begrænsning af hastighed: Ja
Strømforsyning inkluderet: Ja
Stabelbar: Ja
Auto-forhandling: Ja
Pakke bufferlager: 4.1 MB
Hastighed for videresendelse: 23.81 Mpps
Understøttede kabeltyper: Cat3, Cat4, Cat5, Cat5e, Cat6
Kabellængde opdagelse: Ja

Har du brug for hjælp?

Hvis du har brug for hjælp til TP-Link TL-SG116P stil et spørgsmål nedenfor, og andre brugere vil svare dig




Bryter TP-Link Manualer

Bryter Manualer

Nyeste Bryter Manualer

Cudy

Cudy GS108 Manual

16 September 2024
Cudy

Cudy GS105D Manual

16 September 2024
Planet

Planet BSP-115PV-15A Manual

7 September 2024
Planet

Planet BSP-115HP-5A Manual

5 September 2024
Intermatic

Intermatic EJ500 Manual

5 September 2024
STI

STI SS2-3A2EX-ES Manual

21 August 2024
STI

STI SS-2322-EV-ES Manual

21 August 2024
Russound

Russound AB-1.2 Manual

14 August 2024