Uni-T UT58C Manual

Uni-T Multimeter UT58C

Læs nedenfor 📖 manual på dansk for Uni-T UT58C (2 sider) i kategorien Multimeter. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

(See Figure 5)

Transistor Test

for

Overview

Warning

To avoid electric shock or personal injury, read the

“Safety Information”, carefully before using the Meter.

Digital Multimeters Model UT58A, UT58B and UT58C

are 2000-count hand-held instruments with remarkable

features: ex-large LCD, steady operations, overload

protection for all ranges and unique structure. The

Meter can measure AC/DC voltage, AC/DC current,

resistance, capacitance, temperature, frequency,

transistor, diode and continuity, and is equipped with

data hold, full icon display and sleep mode functions.

Unpacking Inspection

In the event you find any missing or damaged part,

please contact your dealer immediately.

1 English Operating Manual

2 Test Lead

3 Multi-Purpose Socket

4 Point Contact Temperature Probe

(UT58B/UT58C only)

5 9V Battery (NEDA 1604, 6F22 or 009P)

Item Description Qty

1 pc

1 pair

1 pc

Safety Information

This Meter complies with the standards IEC61010:

Pollution Degree 2, Overvoltage Category (CAT. II 1000V,

CAT. III 600V) and Double Insulation.

CAT. II: Local level, appliance, PORTABLE EQUIPMENT

etc., with smaller transient voltage overvoltages than

CAT. III

CAT. III: Distribution level, fixed installation, with smaller

transient overvoltages than CAT. IV

Use the Meter only as specified in this operating manual,

otherwise the protection provided by the Meter may be

impaired.

In this manual, a identifies conditions andWarning

actions that pose hazards to the user, or may damage

the Meter or the equipment under test.

A identifies the information that usNote er should pay

Warning

To avoid possible electric shock or personal injury,

and to avoid possible damage to the Meter or to the

equipment under test, adhere to the following rules:

Before using the Meter inspect the case. Do not

use the Meter if it is damaged or the case (or part

of the case) is removed. Look for cracks or missing

plastic. Pay attention to the insulation around the

connectors.

Inspect the test leads for damaged insulation or

exposed metal. Check the test leads for continuity.

Replace damaged test leads with identical model

number or electrical specifications before using

the Meter.

Do not apply more than the rated voltage, as

marked on the Meter, between the terminals or

between any terminal and grounding.

The rotary switch should be placed in the right

position and no any changeover of range shall

be made during measurement to prevent damage

of the Meter.

When the Meter working at an effective voltage

over 60V in DC or 30V rms in AC, special care

should be taken for there is danger of electric

shock.

Use the proper terminals, function, and range

for your measurements.

If the value to be measured is unknown, use the

maximum measurement position and reduce the

range step by step until a satisfactory reading is

obtained.

do not alter the internal circuit of the Meter randomly.

Soft cloth and mild detergent should be used to

clean the surface of the Meter when servicing.

No abrasive and solvent should be used to prevent

the surface of the Meter from corrosion, damage

and accident.

The Meter is suitable for indoor use.

Turn the Meter power off when it is not in use

and take out the battery when not using for a long

time.

Constantly check the battery as it may leak when

it has been using for some time, replace the battery

as soon as leaking appears. A leaking battery will

damage the Meter.

Do not use or store the Meter in an environment

of high temperature,humidity,explosive,inflammable

and strong magnetic field. The performance of

the Meter may deteriorate after dampened.

When using the test leads, keep your fingers

behind the finger guards.

Disconnect circuit power and discharge all high

-voltage capacitors before testing resistance,

continuity, diodes, capacitance or current.

Before measuring current, check the Meter’s

fuses and turn off power to the circuit before

connecting the Meter to the circuit.

Replace the battery as soon as the battery indicator

appears. With a low battery, the Meter might

produce false readings that can lead to electric

shock and personal injury.

Remove test leads, test clips and temperature

probe from the Meter and turn the Meter power

off before opening the Meter case.

When servicing the Meter, use the replacement

parts with the same model or identical electrical

specifications.

To avoid any damage to the meter or any accident,

International Electrical Symbols

AC (Alternating Current).

DC (Direct Current).

Grounding.

Double Insulated.

Low Battery Indication.

Warning. Refer to the Operating Manual.

Conforms to Standards of European Union.

(Figure 1)

The Meter Structure (See Figure 1)

1. Display.LCD

2. Button.HOLD

3. Rotary Switch.

4. Input Terminals.

5. POWER

Functional Buttons

Below table indicated for information about the functional

button operations.

POWER

(Yellow

Button)

Turn the Meter on and off.

Press down the POWER to turn on

the Meter.

Press up the POWER to turn off the

Meter.

HOLD

(Blue

Button)

Press HOLD once to enter hold mode.

Press HOLD again to exit hold mode.

In Hold mode, is displayed and the

present value is shown.

Button Description

No. Symbol Description

The battery is low.

Warning: To avoid false

readings, replace the battery as

soon as the battery indicator

appears.

4Indicates negative reading.

5Test of diode.

6The continuity buzzer is on.

7Date hold is active.

Indicator for AC voltage or current.

The displayed value is the mean

value.

3AC

Connect

Terminal

Indicator of connecting test leads

into different input terminals.

(Figure 2)

(See Figure 2)

Connect Test Leads

COM

Ω Ω Ω

nF FkHz AmAA

AΩ

µAmA

CmVV k M

µA, mA, A

Ω Ω Ω,k ,M

mV, V

µF nF

(Figure 3)

black red

Warning

To avoid harms to you or damages to the Meter from

electric shock, please do not attempt to measure

voltages higher than 1000V although readings may

be obtained.

The DC Voltage ranges are: 200mV, 2V, 20V, 200V and

1000V.

The AC Voltage ranges are: 2V, 20V, 200V and 750V

Measurement Operation

A. Measuring DC and AC Voltage

B. Measuring DC and AC Current (See Figure 4)

(See Figure 3)

To measure DC or AC Voltage, connect the Meter as follows:

1. Insert the red test lead into the HzVΩ(UT58C) or

VΩ(UT58A/UT58B) terminal and the black test

lead into the COM input terminal.

2. Set the rotary switch to an appropriate measurement

position in V or V range.

3. Connect the test leads across with the object to be

measured.

The measured value shows on the display.

black red

(figure 4)

Warning

Never attempt an in-circuit current measurement

where the open circuit voltage between terminals

and ground is greater than 250V .

If the fuse burns out during measurement, the Meter

may be damaged or the operator himself may be hurt.

Warning

To avoid damages to the Meter or to the devices

under test, disconnect circuit power and discharge

all the high-voltage capacitors before measuring

resistance.

(Figure 5)

black red

The resistance ranges are:

Model UT 58A/UT58B:200 ,2k ,20k ,2M ,20M andΩ Ω Ω Ω Ω

200M .Ω

Model UT 58C:200 , 2k , 20k , 2M and 20M .Ω Ω Ω Ω Ω

1. Insert the red test lead into the Hz (UT58C) orVΩ

VΩ (UT58A/UT58B) terminal and the black test

lead into the terminal.COM

2. Set the rotary switch to an appropriate measurement

position in range.Ω

3. Connect the test leads across with the object being

measured.

The measured value shows on the display.

Use proper terminals, function, and range for the

measurement. When the testing leads are connected

to the current terminals, do not parallel them across

any circuit.

The DC Current ranges are:

Model UT58A/ UT58B: 20µA,2mA,20mA,200mA and 20A.

Model UT58C: 2mA, 200mA, 20A

The AC Current ranges are: 2mA, 200mA and 20A

To measure current, do the following:

1.Turn off power to the circuit. Discharge all high-

voltage capacitors.

2. Insert the red test lead into the A or µAmA (UT58A)

or mA (UT58B/UT58C) terminal and the black test

lead into the COM terminal.

3.Set the rotary switch to an appropriate measurement

position in A or A range.

4. Break the current path to be tested. Connect the red

test lead to the more positive side of the break and

the black test lead to the more negative side of the

break.

5. Turn on power to the circuit.

The measured value shows on the display.

black red

(Figure 6)

Note

The test leads can add 0.1to 0.2 of error to the slow-Ω

resistance measurement. To obtain accurate readings

in low-resistance, short-circuit the input terminals

beforehand and record the reading obtained (called

this reading as X). (X) is the additional resistance from

the test lead. Then use the equation:

measured resistance value (Y) – (X)=accurate readings

of resistance.

If the input terminal short-circuit reading 0.5,check

the test leads for any looseness or other cause.

For high resistance (>1M ), it is normal taking severalΩ

seconds to obtain a stable reading; select short test

leads for stable and precise readings.

When the resistance is higher than the maximum range

or in open circuit condition, the Meter displays . “1”

When resistance measurement has been completed,

disconnect the connection between the testing leads

and the circuit under test.

Warning

To avoid damage to the Meter or to the equipment

under test, disconnect circuit power and discharge

all high-voltage capacitors before measuring diodes.

To avoid harms to you, please do not attempt to input

voltages higher than 60V DC or 30V rms AC.

Use the diode test to check diodes, transistors, and other

semiconductor devices. The diode test sends a current

through the semiconductor junction, and then measures

the voltage drop across the junction. A good silicon junction

drops between 0.5V and 0.8V

To test out a diode out of a circuit, connect the Meter as

follows:

1. Insert the red test lead into the Hz (UT58C) orVΩ

VΩ (UT58A/UT58B) terminal and the black test

lead into the COM terminal

2. Set the rotary switch to .

3. For forward voltage drop readings on any semiconductor

component, place the red test lead on the component’s

attention to.

The unit of transistor test

(See Figure 6)

Produkt Specifikationer

Mærke:	Uni-T
Kategori:	Multimeter
Model:	UT58C

Har du brug for hjælp?

Hvis du har brug for hjælp til Uni-T UT58C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Multimeter Uni-T Manualer

3 September 2024

3 September 2024

3 September 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

Multimeter Manualer

Nyeste Multimeter Manualer

21 December 2024

18 December 2024

16 December 2024

15 December 2024

15 December 2024

Vimar 14433.SL Manual

15 December 2024

Kyoritsu KEW-2046R Manual

14 December 2024

Kyoritsu KEW 6010B Manual

14 December 2024

Abus AirSecure CO2WM110 Manual

9 December 2024

Sanwa ACS101 Manual

8 December 2024