V-TAC VT-7-46 Manual

V-TAC Lys VT-7-46

Læs nedenfor 📖 manual på dansk for V-TAC VT-7-46 (2 sider) i kategorien Lys. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
INSTRUCTION MANUAL
LED LINEAR LIGHT - SURFACE
TECHNICAL DATA
SKU
MODEL VT-7-46
40W
3400
120°
0.9
AC: 200-240V, 50Hz
1200x50x65mm
POWER
LUMENS
BEAM ANGLE
DF
INPUT POWER
DIMENSION
20462, 20463, 20464
20466, 20467, 21463
INTRODUCTION
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions
carefully before starting the installation and keep this manual handy for future reference. If you have any another
query, please contact our dealer or local vendor from whom you have purchased the product. They are trained
and ready to serve you at the best.
WARNING
1. Please make sure to turn o the power before starting the installation.
2. Installation must be performed by a qualified electrician.
3. Proper grounding should be ensured throughout the installation.
4. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire shall be replaced.
5. For Indoor use only
6. Before installation, you must carefully check the integrity of the product and accessories
7. When installed, products and flammable materials to ensure that at least 0.2m distance, lighting cannot be
installed in the zenith or heat wall, pay attention to low voltage and high voltage electrical wiring separately.
8. To ensure that the power cord has enough length, do not kink cables. Output cables should be laid separately
and at a distance from other cables.
This marking indicates that this
product should not be disposed
of with other household wastes.
Caution, risk of electric shock.
INSTALLATION DIAGRAM
INSTALLATION INSTRUCTIONS
WIRING DIAGRAM
Switch o the power before starting the installation.
Open end cap from any 1 side of the diuser, slide the diuser into the fitting. Close the end cap
by using screws. (Figure 1)
Choose the right position and drill 2 holes on the mounting surface. Then fix the brackets onto
the mounting surface with help of expansion screws. (Figure 2 & 3)
Connect the wiring as per the wiring diagram, then install the light onto the bracket. (Figure 4).
Switch on the power and test.
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT PLEASE REACH OUT TO US AT
SUPPORT@VTACEXPORTS.COM V-TAC HOUSE, KELPATRICK ROAD, SLOUGH, BERKSHIRE, SL1 6BW, UK.


Produkt Specifikationer

Mærke: V-TAC
Kategori: Lys
Model: VT-7-46

Har du brug for hjælp?

Hvis du har brug for hjælp til V-TAC VT-7-46 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys V-TAC Manualer

V-TAC

V-TAC VT-15021 Manual

2 September 2024
V-TAC

V-TAC VT-12021 Manual

2 September 2024
V-TAC

V-TAC VT-12020 Manual

2 September 2024
V-TAC

V-TAC VT-16011 Manual

2 September 2024
V-TAC

V-TAC VT-16010 Manual

2 September 2024
V-TAC

V-TAC VT-6139 Manual

18 August 2024
V-TAC

V-TAC VT-6072 Manual

18 August 2024
V-TAC

V-TAC VT-6076S Manual

18 August 2024
V-TAC

V-TAC VT-39ST Manual

18 August 2024
V-TAC

V-TAC VT-59ST Manual

18 August 2024

Lys Manualer

Nyeste Lys Manualer