Viewsonic Pro9510L Manual

Viewsonic videoprojektorer Pro9510L

Læs nedenfor 📖 manual på dansk for Viewsonic Pro9510L (98 sider) i kategorien videoprojektorer. Denne guide var nyttig for 44 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/98

Pro9510L/Pro9520WL/

Pro9530HDL/Pro9800WUL

DLP Projector

User Guide

Model No. VS16505/VS16506/VS16507/VS16508

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy, and

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to operate the

equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage

Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment,

display the chemical symbol Hg, Cd, or Pb, then it means that the battery

has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other devices (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade and the third

prong are provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure

that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the unit. When a cart is used, use

caution when moving the cart/unit combination to avoid injury from

tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed

to rain or moisture, or if the unit does not operate normally or has been dropped.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use

of certain hazardous substances in electrical and electronic equipment (RoHS2

Directive) and is deemed to comply with the maximum concentration values issued

by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III

of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode uorescent lamps and external electrode uorescent

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1) Short length ( 500 mm): maximum 3.5 mg per lamp.≦

(2) Medium length ( 500 mm and 1,500 mm): maximum 5 mg per lamp.＞ ≦

(3) Long length ( 1,500 mm): maximum 13 mg per lamp.＞

2. Lead in glass of cathode ray tubes.

3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or

ceramic matrix compound.

This publication, including all photographs, illustrations and software, is protected under international

be reproduced without written consent of the author.

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no

representations or warranties with respect to the contents hereof and specifically disclaims any implied

warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to

revise this publication and to make changes from time to time in the content hereof without obligation of

the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations

and pending applications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing LLC in the United States and other countries.

MHL, the MHL logo, and Mobile High-Definition Link are trademarks or registered

trademarks of MHL licensing, LCC.

All other product names used in this manual are the properties of their respective owners and are

acknowledged.

Ver.:01

Important Safety Information

Important:

It is strongly recommended that you read this section carefully before using the projector. These

safety and usage instructions will ensure that you enjoy many years of safe use of the projector.

Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations.

The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause

personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this

example:

“Push the Menu button on the remote control to open the Main menu.”

General Safety Information

 Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in

the unit. For servicing, contact qualified service personnel.

 Follow all warnings and cautions in this manual and on the unit case.

 The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the

lens when the lamp is on.

 Do not place the unit on an unstable surface, cart, or stand.

 Avoid using the system near water, in direct sunlight, or near a heating device.

 Do not place heavy objects such as books or bags on the unit.

iii

Projector Installation Notice

 Do not tilt the projector to the left or right, otherwise lamp life could decrease dramatically, and

may lead to other unpredictable damages.

 There is no limit on the tilt angle upward or downward.

 Allow at least 50 cm clearance around the exhaust vent.

 Ensure that the intake vents do not recycle hot air from the exhaust vent.

 When operating the projector in an enclosed space, ensure that the surrounding air temperature

within the enclosure does not exceed operation temperature while the projector is running, and the

air intake and exhaust vents are unobstructed.

 All enclosures should pass a certified thermal evaluation to ensure that the projector does not

recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is

with the acceptable operation temperature range.

Minimum 500mm

(19.69 inch)

Minimum 500mm

(19.69 inch)

Minimum 500mm

(19.69 inch)

Minimum 500mm

(19.69 inch)

Minimum 300mm

(11.81 inch)

Power Safety

 Only use the supplied power cord.

 Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot traffic.

 Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 55

for clear and safe instructions for this procedure. Before replacing the lamp:

 Unplug the power cord.

 Allow the lamp to cool for about one hour.

Cleaning the Projector

 Unplug the power cord before cleaning. See Resetting the Lamp Time . page 58

 Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on

page 75.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that

can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal

Laws. For more information, contact the Electronic Industries Alliance at . For lamp WWW.EIAE.ORG

specific disposal information check WWW.LAMPRECYCLE.ORG.

Symbol Explanations

DISPOSAL: Do not use household or municipal waste collection services for

disposal of electrical and electronic equipment. EU countries require the use

of separate recycling collection services.

Main Features

 Compatible with all major video standards including NTSC, PAL, and SECAM.

 A high brightness rating allows for presentations in daylight or in lit rooms.

 Flexible setup allows for front, rear projections.

 - -Line of vision projections remain square, with advanced keystone correction for angled

projections.

 Input source automatically detected.

 High brightness for projection in just about any environment.

 Supports resolutions up to WUXGA for clear and crisp images.

 DLP ® and BrilliantColor™ technologies from Texas Instruments.

 Centered lens for easy installation.

 Horizontal and vertical lens shift.

 MHL device compatibility for streaming of video and audio content from a compatible

mobile device.

 - - - Built in speaker with multiple audio in and audio out ports.

 Network ready for integration and system administration via RJ45.

 Sealed engine to minimizing the impact of dust and smoke.

 Top sided lamp cover for simple lamp removal and insertion.

 -Anti theft security features include: Kensington security slot, security bar.

About this M anual

This manual is intended for end users and describes how to install and operate the DLP projector.

Wherever possible, relevant information such as an illustration and its description has been kept on — —

one page. This printer-friendly format is both for your convenience and to help save paper, thereby

protecting the environment. It is suggested that you only print sections that are relevant to your needs.

vii

Table of Contents

GETTING STARTED .............................................................................................................................................. 1

P C ACKING HECKLIST ............................................................................................................................................. 1

V P P IEWS OF ROJECTOR ARTS................................................................................................................................ 2

Front-right View ............................................................................................................................................... 2

Top view -Screen Display (OSD) buttons and LEDs —On ............................................................................... 3

Rear view ......................................................................................................................................................... 4

Bottom view ..................................................................................................................................................... 6

R C P EMOTE ONTROL ARTS ..................................................................................................................................... 7

Remote control code ....................................................................................................................................... 9

Using the remote mouse control ................................................................................................................... 10

R C O R EMOTE ONTROL PERATING ANGE ................................................................................................................ 10

P R C B ROJECTOR AND EMOTE ONTROL UTTONS..................................................................................................... 10

SETUP AND OPERATI ON................................................................................................................................... 11

I R C B NSERTING THE EMOTE ONTROL ATTERIES ..................................................................................................... 11

S S P TARTING AND HUTTING DOWN THE ROJECTOR ................................................................................................12

S A P L ) ETTING AN CCESS ASSWORD (SECURITY OCK .............................................................................................. 14

A P L DJUSTING THE ROJECTOR EVEL .....................................................................................................................16

A P I P U L S DJUSTING ROJECTED MAGE OSITION SING ENS HIFT ................................................................................ 17

Adjusting the vertical image position ............................................................................................................. 18

Adjusting the horizontal image position ......................................................................................................... 20

A Z , F K DJUSTING THE OOM OCUS AND EYSTONE..................................................................................................... 21

A V DJUSTING THE OLUME ..................................................................................................................................... 22

ON-SCREEN DISPLAY (OSD) MENU SETTINGS ..............................................................................................23

OSD M C ENU ONTROLS ....................................................................................................................................... 23

Navigating the OSD ....................................................................................................................................... 23

S OSD L ETTING THE ANGUAGE............................................................................................................................. 24

OSD M O ENU VERVIEW........................................................................................................................................ 25

I M MAGE ENU....................................................................................................................................................... 28

Advanced Feature ......................................................................................................................................... 29

D M ISPLAY ENU.................................................................................................................................................... 32

V M IDEO/AUDIO ENU ............................................................................................................................................ 33

Audio ..............................................................................................................................................................34

B M ASIC ENU ....................................................................................................................................................... 35

Splash screen ................................................................................................................................................ 36

HV Keystone .................................................................................................................................................. 36

Advanced Feature ......................................................................................................................................... 37

A M DVANCED ENU................................................................................................................................................ 40

Advanced Feature ......................................................................................................................................... 41

OSD Menu Setting ......................................................................................................................................... 42

Lamp Hour Reset .......................................................................................................................................... 42

3D .................................................................................................................................................................. 43

Network Setting ............................................................................................................................................. 43

Status .............................................................................................................................................................54

MAINTENANCE AND SECURITY ....................................................................................................................... 55

R P L EPLACING THE ROJECTION AMP .....................................................................................................................55

Resetting the Lamp Time .............................................................................................................................. 58

C P LEANING THE ROJECTOR ................................................................................................................................. 59

Cleaning the Lens .......................................................................................................................................... 59

Cleaning the Case ......................................................................................................................................... 59

Cleaning the Air Filter .................................................................................................................................... 60

U P L SING THE HYSICAL OCK ................................................................................................................................. 62

Using the Kensington Security Slot ............................................................................................................... 62

Using the Security Bar Lock .......................................................................................................................... 62

TROUBLESHOOTING ......................................................................................................................................... 63

C P S OMMON ROBLEMS AND OLUTIONS .................................................................................................................. 63

T T IPS FOR ROUBLESHOOTING .............................................................................................................................. 63

viii

LED E M RROR ESSAGES...................................................................................................................................... 64

I P MAGE ROBLEMS ...............................................................................................................................................65

L P AMP ROBLEMS................................................................................................................................................. 65

R C P EMOTE ONTROL ROBLEMS............................................................................................................................. 66

A P UDIO ROBLEMS ............................................................................................................................................... 66

H P S AVING THE ROJECTOR ERVICED ..................................................................................................................... 66

HDMI Q & A ....................................................................................................................................................... 67

SPECIFICATIONS ................................................................................................................................................ 68

S PECIFICATIONS.................................................................................................................................................. 68

P D . P S ROJECTION ISTANCE VS ROJECTION IZE ...................................................................................................... 70

PRO9510L / PRO9520WL / PRO9530HDL / PRO9800WUL ....................................................................... 70

T M T IMING ODE ABLE ........................................................................................................................................... 72

P D ROJECTOR IMENSIONS .................................................................................................................................... 74

REGULATORY COMPLIANCE ........................................................................................................................... 75

FCC W ARNING ...................................................................................................................................................75

C ANADA.............................................................................................................................................................. 75

S C AFETY ERTIFICATIONS ..................................................................................................................................... 75

APPENDIX I .........................................................................................................................................................76

IR CODE TABLE .................................................................................................................................................... 76

APPENDIX II ........................................................................................................................................................ 77

RS-232C P ROTOCOL.......................................................................................................................................... 77

G S ETTING TARTED

Packing Checklist

Carefully unpack the projector and check that the following items are included:

Projector

Remote Control

(Batteries Included)

VGA Cable

Power Cord

CD-ROM

(This User's Manual)

Quick Start Guide

Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is

recommend that you keep the original packing material should you ever need to return the equipment for

warranty service.

Caution:

Avoid using the projector in dusty environments.

Views of Projector Parts

Front-right View

I TEM

L ABEL

D ESCRIPTION

S EE PAGE

Lamp Cover

Remove cover to replace lamp.

Tilt Adjuster

Rotate adjuster lever to adjust angle position.

Lens

Projection Lens.

IR Receiver

Receives IR signal from remote control.

LEDs

Displays the projector status.

Vent

Cool air intake.

Vertical Lens Shift

Adjusts the image position vertically.

Horizontal Lens Shift

Adjusts the image position horizontally.

Zoom Ring

Enlarges the projected image.

10.

Focus Ring

Focuses the projected image.

11.

Function Keys

On-Screen Display (OSD) buttons.

Important:

Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp

cool. Do not obstruct any of the ventilation openings.

1 2 3 4 5 2

Rear view

I TEM

L ABEL

D ESCRIPTION

S EE PAGE

HDMI 1 /MHL

Connect the HDMI/MHL cable from an HDMI/MHL device.

Note: Set the Source to HDMI 1/MHL also can be charging connected

MHL compatible smart device as long as the projector Power

On.

HDMI 2

Connect the HDMI cable from an HDMI device.

DVI-D

Connect the DVI CABLE to a display.

RS-232

Connects RS-232 serial port cable for remote control.

Computer Out

Connect an RGB cable to a display (Pass through by VGA1 only).

S-VIDEO

Connect a S-VIDEO cable from a video device.

Computer In 1

Connect an RGB cable from a computer or a video enabled device.

BNC

Connect a BNC cable from a computer.

Computer In 2

Connect an RGB cable from a computer or a video enabled device.

10.

RJ45 (LAN)

Connect a LAN cable from Ethernet.

11.

USB

Connect a USB cable for USB host.

Note: Support 5V/1.0A for each port output as long as the projector

Power On.

12.

3D- VESA

Connect 3D IR glasses receiver unit.

13.

Kensington Security Slot

Secures to permanent object with a Kensington Lock

system.

14.

AUDIO IN L/R

Connect the audio cables from an audio device for VIDEO or

S-VIDEO audio input.

15.

AUDIO IN

Connect an AUDIO cable from the input device.

16.

Receive IR signal from remote control.

17.

12V OUT

When connected to the screen through a commercially available

cable, the screen deploys automatically on start up of the projector.

The screen retracts when the projector is powered off (see notes

below).

18.

AUDIO OUT

Connect an AUDIO cable for audio loop through.

19.

AUDIO OUT L/R

Connect an AUDIO cable for audio loop through.

20.

VIDEO

Connect the composite cable from a video device.

S-Video

Serv eic

Video RL

Audio

In DVI-D In 1 In 2

Audio

A oudi

OutMIC

Computer 1In

R G B H V

Computer Ou t LANCom puter 2In 3D V ESAUSB

RS 232-

DVI-D

HDM I 2HDM I 1 MH L/

IRAudio Out

In Ou tRemote

Wired

12V Out

1 2 3 4 5 6 7 8 9 1011 12

1314

Bottom view

I TEM

L ABEL

D ESCRIPTION

S EE PAGE

Tilt Adjustor

Rotate adjuster lever to adjust angle position.

Ceiling Mount Holes

Contact your dealer for information on mounting the projector on a

ceiling.

Note:

When installing, ensure that you use only UL Listed ceiling mounts.

For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw

depth of mm (0. inch). 12 47

The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount

load capacity must exceed the weight of the installed equipment, and as an additional precaution

be capable of withstanding three times the weight of the equipment over a period of 60 seconds.

Ceiling mount screws:

M4 x 5 (Max. L = 12 mm)

Unit: mm

I TEM

L ABEL

D ESCRIPTION

S EE PAGE

IR Transmitter

Transmits signals to projector.

Power On

Turns the projector on.

HDMI

Displays the HDMI 2 source.

COMP

Displays the VGA1/VGA2 source selection (toggle).

Video

Displays the VIDEO -VIDEO source selection. /S

Navigates and changes settings in the OSD.

Quick Menu For Vertical Keystone. –

Auto SYNC

Auto adjustment for frequency, phase, and position.

Navigates and changes settings in the OSD.

Quick Menu For Horizontal Keystone. –

Opens the OSD.

10.

Navigates and changes settings in the OSD.

Quick Menu For Vertical Keystone. –

11.

Laser

Press to operate the on-screen pointer. DO NOT POINT IN EYES.

12.

Performs the same function as the left mouse button when the mouse

mode is activated.

13.

MOUSE

Switches between the normal and mouse modes.

PgUp, PgDn, , : active after pressing , ▲, ▼, ◄, ►,

Mouse. An icon appears on the screen to indicate the activation of the

mouse mode.

Note: Only available when a PC input signal is selected.

14.

ID SET

Sets remote control code

15.

PgUp / 1

Perform page up function when mouse mode is activated.

Number for Remote ID setting used.

16.

Blank / 3

Makes the screen blank.

Number for Remote ID setting used.

17.

/ 4

Mutes the built-in speaker.

Number for Remote ID setting used.

18.

/ 6

Selects the display aspect ratio.

19.

Displays the presentation timer settings menu.

20.

ECO MODE

Selects a lamp mode.

21.

Activates panel key lock.

22.

Laser

Use as on-screen pointer. DO NOT POINT IN EYES.

23.

Allows user to define a short cut key on the remote

control, and the function item is selected in OSD menu.

24.

HDMI / MHL

Displays the HDMI1 source.

Enable the Mobile High-Definition Link technology feature for smart

devices.

25.

Source

Alternate input source.

26.

BNC

Displays the BNC source.

27.

Freeze

Freezes/unfreezes the on-screen picture.

I TEM

L ABEL

D ESCRIPTION

S EE PAGE

28.

Enters and confirms settings in the OSD.

Displays the Corner Adj. page.

29.

Navigates and changes settings in the OSD.

Quick Menu For Horizontal Keystone. –

30.

EXIT

Return to last OSD page.

31.

Performs the same function as the right mouse button when the mouse

mode is activated.

32.

PgDn / 2

Perform page down function when mouse mode is activated.

Number for Remote ID setting used.

33.

PATTERN / 5

Displays embedded test pattern.

Number for Remote ID setting used.

34.

/ 7

Increase the volume level..

Number for Remote ID setting used.

35.

/ 8

Displays the HELP menu.

Number for Remote ID setting used.

36.

Decreases the volume level.

37.

Displays the digital zoom settings bar.

38.

COLOR MODE

Selects an available picture setup mode.

39.

Wired Jack

Connect wire remote to the projector.

Remote control code

The projector can be assigned to 8 different remote control codes, 1 to 8. When several adjacent

projectors are in operation at the same time, switching the remote control codes can prevent interference

from other remote controls. Set the remote control code for the projector first before changing that for the

remote control.

To switch the code for the projector, select from among 1 to 8 in the Basic > Advanced > Remote Control

Code menu.

To switch the code for the remote control, press ID set and the corresponding button from 1 to 8 buttons

on the remote control together for 5 seconds or more. The initial code is set to1. When the code is

switched to 8, the remote control can control every projector.

Note:

If different codes are set on the projector and remote control, there will be no response from the

remote control. When that happens, switch the code for the remote control again.

Using the remote mouse control

The capability of operating your computer with the remote control gives you more flexibility when delivering

presentations.

1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in

place of your computer’s mouse.

2. Set the input signal to COMPUTER.

3. Press Mouse on the remote control to switch from the normal mode to the mouse mode. An icon

appears on the screen to indicate the activation of the mouse mode.

4. Perform the desired mouse controls on your remote control.

 To move the cursor on the screen, press ▲ / ▼ / ◄ / ►/ .

 To left-click, press .

 To right-click, press .

 To operate your display software program (on a connected PC) which responds to page up/down

commands (like Microsoft PowerPoint), press Page Up/Page Down.

 To return to the normal mode, press Mouse again or other keys except for the mouse related

multi-function keys.

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the

remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the

rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15

degrees above or below the projector level. If the projector does not respond to the remote control, move a

little closer.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All

operations can be carried out with the remote control; however, the buttons on the projector are limited in

use.

Produkt Specifikationer

Mærke:	Viewsonic
Kategori:	videoprojektorer
Model:	Pro9510L
Vekselstrømsindgangsspænding:	100 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	445 mm
Dybde:	147.8 mm
Højde:	325.5 mm
Vægt:	8290 g
Brugervejledning:	Ja
Produktfarve:	Hvid
Indbygget skærm:	Ingen
Produkttype:	Standard kasteprojektor
Pakkevægt:	12400 g
Pakkedybde:	291 mm
Pakkebredde:	574 mm
Pakkehøjde:	576 mm
Wi-Fi:	Ingen
Naturligt aspektforhold:	4:3
3D:	Ingen
Indbyggede højttaler(e):	Ja
Relativ luftfugtighed ved drift (H-H):	10 - 85 %
Udgangseffekt (RMS):	14 W
Antal HDMI-porte:	1
Mobile High-Definition Link (MHL):	Ja
DVI-port:	Ja
Ethernet LAN-porte (RJ-45):	1
Antal USB 2.0-porte:	2
Udgange til hovedtelefoner:	1
Ethernet LAN:	Ja
Skærmvisning (OSD):	Ja
Strømforbrug (standby):	0.5 W
Driftstemperatur (T-T):	5 - 40 °C
Hurtig start guide:	Ja
Kabler inkluderet:	AC, VGA
Batterier inkluderet:	Ja
Understøttede grafikopløsninger:	1024 x 768 (XGA), 1920 x 1080 (HD 1080)
Sammensat videoindgang:	1
Støjniveau:	- dB
Fjernbetjening inkluderet:	Ja
Strømkilde:	Vekselstrøm
Certificering:	UL, cUL, FCC, CE, EMC, CB, REACH, SVCH, WEEE, ErP, NOM/ENERGY, PSB, RCM, CCC
Strømforbrug (maks.):	480 W
Placering:	Desktop
Indbygget kortlæser:	Ingen
Antal indbyggede højttalere:	2
Pc lydindgang:	Ja
Bæredygtighedscertifikater:	RoHS
Slot til kabellås:	Ja
Optisk zoom:	1.7 x
Fokus:	Vejledning
Antal farver:	1.073 milliarder farver
Lyd (L, R) indgang:	1
Horisontal scanningsområde:	15 - 100 kHz
HDMI-version:	1.4
Antal VGA-porte (D-sub):	3
Kabellåseslids type:	Kensington
Lyd (L, R) udgang:	1
Zoom kapacitet:	Ja
Brændviddeområde:	- mm
Projektor lysstyrke:	6200 ANSI lumens
Projektionsteknologi:	DLP
Projektor indbygget opløsning:	XGA (1024x768)
Skærmstørrelse kompatibilitet:	30 - 300 "
Projiceringsafstand:	1 - 17 m
Trapezkorrektion, vertikal:	± 30 °
Vertikalt scanningsområde:	24 - 120 Hz
Throw-forhold:	1.3 - 2.21:1
Zoom type:	Vejledning
RS-232-porte:	1
Levetid for lyskilde:	1500 t
Lampeeffekt:	370 W
Levetid for lyskilde (økonomisk tilstand):	3500 t
Lyskilde type:	Lampe
Antal af S-video-indgange:	1
Seriel grænsefladetype:	RS-232
Trapezkorrektion, horisontal:	± 30 °
Horisontalt område for optisk linseforskydning:	-3.8 - 3.8 %
Vandret område for optisk linseforskydning:	-10.5 - 3 %
PC-lydudgang:	Ja
Fjernbetjening (IR) udgang:	1