Vivotek AW-IHT-0200 Manual


Læs nedenfor 📖 manual på dansk for Vivotek AW-IHT-0200 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
LC
VDC: 48V ~ 56V
AC-to-DC power
100~240 VAC IN
(DO NOT connect external power
supply to V2!)
POWER Green ON Power is on and normal.
Fiber Link/
Act
Green ON Fiber is attached.
Green Flashing Data is being transmitted / received.
LAN port
Green
Green ON TX link is detected.
Green Flashing Data is being transmitted or received.
PoE port
Amber
Amber ON PSE is activated and PD is detected.
Amber Flasing SFP data is being transmitted or received.
1. Install the converter in a ventilated and dry place that is free of electromagnetic source, vibration, moisture, and dust.
2. Make sure the ventilation openings on the converter are not blocked.
3. Use ber optic cables and transceiver compliant with the following: Multi-mode: 50/125um, 62.5/125um, 850/1310nm;
Single-mode: 9/125um ,1310/1550nm.
4. DC input: 48V~56VDC. Follow the printed polarity for V+, V-, and Ground.
AW-IHT-0200 Industrial PoE Switch
Quick Installation Guide
The AW-IHT-0200 is a rugged Gigabit switch designed for critical and space-limited outdoor applications. Designed for
IP surveillance, trafc monitoring, and security applications in critical environments, the converter can deliver a 30W
output on Ethernet port. The converter features a wide range of VAC and VDC input range, and an operating temperature
ranging from -40°C to 75°C.
IMPORTANT:
INTRODUCTION
LED DEFINITIONS
CONNECTION
* 1x PoE switch * 1x Quick Installation Guide
* 2x wall mount brackets * 1x DIN rail bracket
* 1x 4-pin terminal block
PACKAGE CONTENTS
ON
OFF
21
DIP 1 OFF no use, reserved.
ON
DIP 2 OFF 1000Mbps speed for SFP port (default)
ON 100Mbps speed for SFP port
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
| | |T: +886- 2-82455282 F: +886-2-82455532 E: sales@vivot ek.com
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
| | |T: 408-773-8686 F: 408-773-8298 E: salesusa@vivotek.com
VIVOTEK Europe
Randstad 22-133, 1316BW Almere, The Netherlands
T E: +31(0)36-5298-434 : saleseurope@vivotek.com
All specications are subject to change without noice.
Copyright © 2015 VIVOTEK INC. All rights reserved.
Solid or stranded (AWG): 12-24/14-22.
Wire strip length: 7-8mm
Torque: 5lb-In/0.5Nm/0.56Nm.
WARNING - Always ground the power source to maintain a clean power input.
- Always shut off power source before connecting power wires.
1. Pull out the 4-pin terminal block.
2. V1(power input): Connect positive wire of external
power supply to V1 +, negative wire to V1 -, and
neutral wires to the ground screw.
3. V2(relay output): Connect the 24VDC@1A pins
to external devices, When 2 power pins are
connected, the relay is shorted. When any of them
is disconnected, the relay connection is open.
4. Connect an SFP transceiver to the ber port.
5. install the 4-pin terminal block. You can connect
redundant power line pairs for fault tolerance.


Produkt Specifikationer

Mærke: Vivotek
Kategori: Ikke kategoriseret
Model: AW-IHT-0200

Har du brug for hjælp?

Hvis du har brug for hjælp til Vivotek AW-IHT-0200 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Vivotek Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024