Westinghouse W24V2AMP Manual


Læs nedenfor 📖 manual på dansk for Westinghouse W24V2AMP (2 sider) i kategorien Effektmaskine. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
1
SAVE THESE INSTRUCTIONS
mWARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious personal injury.
mCAUTION! To reduce the risk of injury, charge the 24V lithium-ion battery packs only in
its designated 24V lithium-ion charger. Other types of chargers present risk of fire,
personal injury and damage. Do not wire a battery pack to a power supply plug or car cigarette
lighter. Such misuse will permanently disable or damage the battery packs.
Avoid dangerous environments – Do not charge the battery packs in rain, snow or in
damp or wet locations. Do not use the battery packs or charger in the presence of explosive
atmospheres (gaseous fumes, dust or ammable materials) because sparks may be
generated when inserting or removing the battery pack, which could lead to a re.
Charge in a well-ventilated area – Do not block the charger vents. Keep them clear to allow
for proper ventilation. Do not allow smoking or open ames near a charging battery pack.
Vented gases may explode.
NOTE: The safe temperature range for the batteries is 41°F – 105ºF (5°C – 40.5°C). Do not
charge the batteries outside in freezing weather; charge it at room temperature.
Maintain charger cord – When unplugging the charger, pull the plug, not the cord, from
the receptacle to reduce the risk of damage to the electrical plug and cord. Never carry the
charger by its cord or yank it by the cord to disconnect it from the receptacle. Keep the cord
away from heat, oil and sharp edges. Make sure the cord will not be stepped on, tripped over
or subjected to damage or stress when the charger is in use. Do not use the charger with a
damaged cord or plug. Replace a damaged charger immediately.
Using the wrong, Do not use an extension cord unless it is absolutely necessary –
damaged or improperly wired extension cord poses a risk of re and electric shock.
The charger must be plugged into an appropriate Charger is rated for 120 volt AC only –
receptacle.
Use only recommended attachments – Use of an attachment not recommended or sold by
the battery charger or battery pack manufacturer may result in risk of re, electric shock or
personal injury.
Make sure to remove the battery packs from Unplug charger when not in use –
unplugged charger.
mWARNING! To reduce the risk of electric shock, always unplug the charger before
performing any cleaning or maintenance. Do not allow water to ow into the charger. Use a
Ground Fault Circuit Interrupter (GFCI) to reduce shock hazards.
Store your charger in a cool, dry place – Do not store charger where temperatures may
exceed 105ºF (40.5ºC), such as in direct sunlight or inside a vehicle or metal building during
the summer.
Charge times vary. Refer to battery specications.
Charger Input .................................................................................................120V AC, 60 Hz, 75 W
Charger Output .................................................................................................................. 26V* Max
Battery Charge Level Indicator
Each battery pack is equipped with a push button for checking the charge level. Simply press the
push button to read o the battery charge level from the LEDs of the battery indicator:
When to Charge the Lithium-Ion Batteries
NOTE: The 24V lithium-ion battery packs do not develop a “memory” when charged after only
a partial discharge. Therefore, it is not necessary to run down the battery pack before
connecting it with the charger.
Use the battery charge indicator lights to determine when to charge your 24V
lithium-ion battery packs.
You can “top-off” your battery packs’ charge before starting a big job or after a
long day of use.
Charge the Battery
1. Press the push lock buttons on the battery to pull it out of the equipment.
2. Check that the mains voltage is the same as that marked on the rating plate of the battery
charger. Then, insert the charger’s plug into the electrical wall outlet. When you plug in the
charger, the top right green light will illuminate and stay green (Fig. ).1
3. Place the battery packs into the charger by sliding the packs to lock them into position.
When you insert the batteries into the charger, the green light will go off, and the red light
will illuminate to indicate that the batteries are charging (Fig. 2).
SAFETY INSTRUCTION
TECHNICAL DATA
*Initial no-load voltage, when fully charged, peaks at 26 volts; nominal voltage under typical load is 25.2 volts.
OPERATION
W24V2AMP
24V 2.2 AMP CHARGER
FOR WESTINGHOUSE 24V BATTERIES
To register your Westinghouse battery pack on-line, visit us at:
wpowereq.com/pages/warranty-registration
All 3 A, B, C LEDs are lit: Battery charge level is high.
Light A, B LEDs are lit: Battery charge level is decreasing. Stop work as
soon as possible.
Light A LED is lit: Battery is flat. Stop work IMMEDIATELY and charge the
battery. Otherwise the battery’s service life will be greatly shortened.
Fig. 2


Produkt Specifikationer

Mærke: Westinghouse
Kategori: Effektmaskine
Model: W24V2AMP

Har du brug for hjælp?

Hvis du har brug for hjælp til Westinghouse W24V2AMP stil et spørgsmål nedenfor, og andre brugere vil svare dig




Effektmaskine Westinghouse Manualer

Effektmaskine Manualer

Nyeste Effektmaskine Manualer

GLP

GLP JDC2 IP Manual

12 December 2024
Karma

Karma TM WASH70 Manual

19 November 2024
Audibax

Audibax Geyser 2000 Manual

2 November 2024
Audibax

Audibax Smoke 1200 Manual

2 November 2024
Magmatic

Magmatic CRISP Manual

2 September 2024
Magmatic

Magmatic CRISP MAX Manual

2 September 2024
Magmatic

Magmatic SIDEWINDER Manual

2 September 2024
Magmatic

Magmatic JAVELIN Manual

2 September 2024