Yamaha DTX920K Manual

Yamaha Musikinstrument DTX920K

Læs nedenfor 📖 manual på dansk for Yamaha DTX920K (2 sider) i kategorien Musikinstrument. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

This manual describes the standard assembly procedure for the DTX760K/DTX920K electronic drum kits. It covers assembly and wiring of the kit as shown below.

When you have completed all of the steps described, you will be ready to turn on the drum trigger module and start playing.

Illustrations show the DTX700 drum trigger module.

ELECTRONIC DRUM KIT

DTX760K/DTX920K Assembly Manual

• For assembly, you will require four individual packages – an RS700

Rack System, a DTP903 Pad Set, a DTP904 Pad Set, and a DTX700/

DTX900M Drum Trigger Module.

• This manual describes the process of assembling a drum-pad set and

drum trigger module to an already assembled RS700 Electronic Drum

Rack. Before starting the steps below, therefore, be sure to assemble

your RS700 as described in the Owner’s Manual that came with it.

Before starting assembly, lay a drum mat (sold separately) on the floor.

Alternatively, you can place cardboard from the drum kit packaging or the

like on the floor to prevent it from being scratched. This is particularly

important when using the HS740A Hi-hat Stand and KP100 Kick Pad.

IMPORTANT

NOTICE

Example of standard assembly

PCY155

(Cymbal Pad)

PCY135

(Cymbal Pad)

CH750

(Cymbal Holder)

RHH135

(Real Hi-hat Pad)

DTX700/DTX900M

Drum Trigger Module

HS740A

(Hi-hat Stand)

XP100T

(Tom Pad)

XP120SD

(Snare Pad)

SS662

(Snare Stand)

CH750

(Cymbal Holder)

PCY135

(Cymbal Pad)

CH755

(Cymbal Holder)

XP120T

(Tom Pad)

KP100

(Kick Pad)

RS700

(Rack System)

The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating the severity and immediacy

of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The instructions disp these precautions layed together with

are extremely important in terms of ensuring safety, and therefore, they should be fully observed.

* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.

* Be sure to also read the Assembly Manuals and/or Owner’s Manuals that came with your pads and rack.

NOTICE: Usage Precautions

• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition,

avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Failure to avoid

these precautions can lead to cable breakage and disconnection.

• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe this pre-

caution can result in malfunction.

• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close proximity to

a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or outdoors in wet weather).

Failure to observe this precaution can lead to warping, discoloration, malfunction, or breakdown.

• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these substances

can cause warping and discoloration. Instead, we recommend you remove dust using a soft dry cloth or

wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first wipe the dirt away

using a cloth moistened with a neutral detergent solution and tightly wrung. Following this, wipe away the

detergent solution using a cloth soaked in water and tightly wrung.

Safety Precautions Please read carefully before proceeding.

Failure to observe the precautions described below can result in se-

rious injury or even death.

• Young children using this electronic drum kit should be supervised by a guardian to eliminate any

possibility of injury.

• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should

take special care whenever handling these components.

• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-

fore, you should take special care whenever handling these components.

• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In

addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads

may fall off or the rack may collapse or fall over, possibly causing injury.

• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe

surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.

• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If

someone were to trip on a cable, the kit could topple over and cause injury.

• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to

observe this precaution can result in injury or malfunction.

• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing injury.

WARNING

Failure to observe the precautions described below can result in in-

jury and/or property damage.

• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during

this operation.

• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by

sharp tips if these components are not handled carefully.

• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.

• Do not use the electronic drum kit’s rack to hold acoustic drums. Doing so could cause clamps to

break and the drums to fall off, which in turn could lead to injury.

CAUTION

Manual Development Department

Published 10/2015 POTO*.*-**A0

Printed in Japan

ZT57980

Assemble the RS700 Electronic Drum Rack.

For instructions on how to assemble the RS700 Electronic Drum Rack, refer to the Owner’s Manual that came with it.

Open the boxes to reveal their contents.

Assemble the pads and the drum trigger module to the electronic drum rack.

Package 1: DTP903 Package 2: DTP904

PCY135

Cymbal Pad (x2)

PCY155

Cymbal Pad (x1)

RHH135

Real Hi-hat Pad (x1)

Stand base for the

RHH135 (x1)

CH750

Cymbal Holder (x2)

CH755

Cymbal Holder (x1)

HS740A

Hi-hat Stand (x1)

Hi-hat clutch for the

RHH135 (x1)

Cable band for the

RHH135 (x1)

Stoppers for the

PCY135 and

PCY155 (x3)

 2.5m stereo phone cables (x4) 4m stereo phone cables (x6)

Felts for the

PCY135 and

PCY155 (x3)

Cable bands (x10)Tuning key (x1)KP100 Owner’s Manual (x1)

PCY100/PCY135/PCY155 Owner’s Manual (x1)

RHH135 Owner’s Manual (x1)

XP120SD

Snare Pad (x1)

XP100T

Tom Pad (x2)

XP120T

Tom Pad (x1)

Clamp bolts (x3)

KP100

Kick Pad (x1)

SS662

Snare Stand (x1)

XP100T/100SD/120T/120SD Owner’s Manual (x1)

Assembly Manual (this pamphlet)

Package 3: DTX700/DTX900M

DTX700/DTX900M

Drum Trigger Module (x1)

 Module holder (x1) Module holder screw

(x4)

AC power adaptor* (x1)

* May not be included depending on your particular area.

Please check with your Yamaha dealer.

DTX700/DTX900M Owner’s Manual (x1)

DTX700/DTX900M Data List (x1)

Assembling the cymbal holders Assembling the tom pads

1. Assemble the cymbal holders (CH750 x 2, CH755 x 1) on the electronic

drum rack as shown below.

CH750

CH755

1. Attach the clamp bolt to each of the tom pads and pro-

visionally tighten (by 5 or 6 turns).

2. Push the tom pads onto the rack’s clamp rods. Ensure

that the rod section is fully inserted into the each pad’s

mounting hole, and then tighten the clamp bolt to se-

cure the pad in place.

3. Loosen clamp bolts A to E as shown below to adjust

the height and angle of any of the pads. When correct-

ly positioned, be sure to securely retighten the bolts

before proceeding to the next step.

XP100T

XP120T

Tom pad (rear side)

Clamp bolt (tighten in the

direction of the arrow)

Tom pad

Rod section Clamp rod

Insert

Clamp bolt

Clamp bolt B

Clamp bolt D

Clamp bolt E

Clamp bolt A

Clamp bolt C

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time

without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Continued on other side