3M SM 8100-YS Manual

3M Kabler til computere og periferiudstyr SM 8100-YS

Læs nedenfor 📖 manual på dansk for 3M SM 8100-YS (26 sider) i kategorien Kabler til computere og periferiudstyr. Denne guide var nyttig for 48 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/26

3M™ Hot Melt Fiber Optic Connectors

ST, SC and FC

Instructions

June 2011

78-8073-7873-8-E

Contents

1.0 Safety and Helpful Hints ....................................................................................................................... 3

2.0 3M™ Field Termination Kit Contents..................................................................................................... 4

3.0 3M™ Hot Melt ST Connector 900 µm Buffered Fiber .......................................................................... 6

4.0 3M™ Hot Melt ST Connector 3 mm Jacketed Cable ............................................................................. 8

5.0 3M™ Hot Melt SC Connector 900 µm Buffered Fiber ........................................................................10

6.0 3M™ Hot Melt SC Connector 3 mm Jacketed Cable........................................................................... 12

7.0 3M™ Hot Melt FC Connector 900 µm Buffered Fiber ........................................................................14

8.0 3M™ Hot Melt FC Connector 3 mm Jacketed Cable........................................................................... 16

9.0 Scribing ................................................................................................................................................18

10.0 Multimode Polishing: Hot Melt ...........................................................................................................19

11.0 Singlemode Polishing: Hot Melt .........................................................................................................21

13.0 Finishing ...............................................................................................................................................24

14.0 Field Termination Kit Replacement Part Numbers .............................................................................25

2.0 3M™ Field Termination Kit Contents

2.1 2.2 3MCarrying Case, 1 ea. ™

Hot Melt Oven 6312 (120 V) or 6323

(230 V) with heat guard, 1 ea.

2.3 3M™ Universal Connector Holder 6365-HH,

6 ea.

2.4 3M™ Polishing Pad 6365-PP, 2 ea 2.5 3M™

Lapping Film 9 µm (gray), 10 sheets. 2.6 3M™ Lapping Film 2µm (pale green),

50sheets

2.7 3M™ Final Polish Film 0.05µm (frost white),

20 sheets

2.8 3M™

Polishing Jig 8892, 2 ea. 2.9 3M™ Aramid Yarn Snips 6365-KS, 1 ea.

2.10 3M™ Stripping Tool 6362-TH, 1 ea. 2.11 3M™

Crimp Tool 6365-CT, 1 ea. 2.12 3M™ Fiber Scribe 6365-FS, 1 ea.

2.13 3M™ View Scope 6365-VS, 1 ea. Strip Templates, 1 ea. Fiber Marking Pen, 1 ea.2.14 2.15

2.16 3M™ Pronto™ Instant Adhesive, CA-8, 1 ea. 2.17 3M™

Lint-Free Cloths 6366-CW, 100 pcs. Alcohol and Water Bottles (shipped empty), 2.18

1 ea.

2.19 Fiber Scrap Can, 1 ea. Training CD Rom, 1 ea.2.20

3.0 3M™ Hot Melt ST Connector 900 µm Buffered Fiber

A B C

3.1 Plug in the 120V or 230V power cord.

Turn on the 3M™ Hot Melt Oven. The oven

requires six minutes to warm up.

3.2 Open the connector package and remove

components.

3.3 Each connector package contains a

connector (A), strain relief boot (B), and

clear strain relief tube (C).

3.4 Load ST Connector into the shorter end of

the 3M™ Universal Connector Holder.

3.5 Place the connector holder into an available

port in the oven.

Note: The hot melt connector should be in

the oven for at least 60 seconds. The

connector should not be in the oven

longer than five minutes.

3.6 Place the strain relief boot and clear strain

relief tube on the buffered fiber, as shown.

7/8"

(22 mm)

3.7 Place the buffered fiber on the strip

template for “ST Hot Melt” and use the fiber

marking pen to mark the location of the

buffer cut.

3.8 Strip Template 3.9 Using the 3M™ Stripping Tool 6362-TH,

remove the buffer in small pieces until 7/8”

(22 mm) of buffer has been removed.

3.10 Using a lint free cloth moistened with

Isopropyl alcohol, clean the bare fiber to

remove any oils or Acrylate coating debris.

3.11 Check the final strip lengths and adjust if

necessary.

3.12 Position the clear strain relief tubing

towards the end of the fiber where it will be

easily accessible.

Produkt Specifikationer

Mærke:	3M
Kategori:	Kabler til computere og periferiudstyr
Model:	SM 8100-YS
Materiale:	Termoplastisk elastomer (TPE)
Grænsefladetype:	ST
Stik:	1
Ydre diameter:	0.125 mm