ABB DY GPS Manual


Læs nedenfor 📖 manual på dansk for ABB DY GPS (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
REFERENCE STANDARDS
Compliance with Community Directives:
2014/30/EU (EMCD)
2014/53/EU (RED)
is declared with reference to the following harmonized standards:
• EN 60950-1
• ETSI EN 301 489-1, ETSI EN 301 489-3, ETSI EN 300 440-1, ETSI EN 300 440-2
4
5
1User Manual
GPS MODULE FOR EXTERNAL USE
Read all the instructions carefully
DIMENSIONS (mm)
DEVICE STATUS
INSTALLATION
2
DY GPS
is a GPS module that allows you to capture the information of
date, time and position from satellites. This information may be shared
with DY365 device designed to interface with
DY GPS
, so as to ensure a
synchronization always perfect.
Code Model Description
2CSM250411R1000 DY GPS GPS module for external use
SAFETY WARNINGS
During product installation and operation it is necessary to observe the
following instructions:
1) The product must be installed by a qualified person, in strict compliance
with the connection diagrams.
2) Do not power the instrument if any part of it is damaged.
3) The product must be installed and activated in compliance with current
electric system standards.
4) The electrical system in the building in which the product is to be installed
should have an over-current switch and a protection device.
5) Do not use the product for purposes different from the one specified.
6) In case of malfunction do not perform repairs and contact immediately the
technical support.
7) The product can be used in environments with category of overvoltage III
and pollution degree 2.
8) Before accessing the connection terminals, verify that the leads are not live.
9) After installation, inaccessibility to the connection terminals without
appropriate tools must be guaranteed.
TECHNICAL CHARACTERISTICS
Power supply: 12V DC (-20% ÷ +20%)
Absorption: 30mA max (during receiving GPS)
Wall or pole installation
Wiring
– Cable length: 100m
– Flexible cables section: 0.75 ÷ 1.5 mm
2
– Sheathed cables maximum diameter: 3 mm
Protection degree: IP54
Operating temperature: 0 ÷ +50 °C
Storage temperature: -25 ÷ +70 °C
Operating humidity: 20÷90% non condensing
Key to force sending data to the connected devices
Red / green / orange led for signaling device status (Figure 1)
Led for signaling
device status
Key to force sending data
to the devices
79
52
20
41
Installation can be wall or pole (by using the adapter in the package)
Remove the cover by leveraging the teeth on the sides of the product
Pass the cables through the cable entry on the bottom side and connect the
power and bus cables respecting the wiring diagram
Tighten the cable gland and replace the cover.
When you power on the led emits two red flashes as follows:
OFF ON OFF ON OFF
1 s 1 s 1 s
After the power on sequence, the DY GPS:
- acquires data of time, date, latitude, longitude and number of satellites received
about every 30 seconds
- sends data of time, date, latitude, longitude to the I/O extension port (and to the
connected devices) every 30 minutes
The flashing of the green led indicates the number of the received satellites
(the higher the number of satellites received, the better the reception of the
information):
Number of satellites Green led sequence
ON OFF REPETITIONS
0 - 2 500 ms 500 ms continuous
3 – 5 100 ms 300 ms 3 every 5 seconds
6 – 8 100 ms 300 ms 6 every 5 seconds
9 – 12 100 ms 300 ms 9 every 5 seconds
Sending data to the I/O extension port (and to the connected devices) is signaled
by the red flashing of the led for 3 seconds as follows:
ON OFF ON OFF …..
100 ms 100 ms 100 ms 100 ms …..
Note: at any time you can force sending data to the I/O extension port by pressing
the key (accessible by removing the cover, see figure 2).
Failure to receive the correct data for more than 60 seconds causes an auto-reset
of the device. After three fruitless recovery attempts, this condition is signaled by
the red flashing of the led as follows:
ON OFF ON OFF …..
500 ms 500 ms 500 ms 500 ms …..
In this case, the DY GPS tries to restore the operation of the GPS module by
continuing signaling; in case it succeeds, it will return to normal operation (flashing
of the led of green colour according to the number of the detected satellites).
Failure to receive the correct data for more than 30 minutes causes an auto-
reset of the device with loading of factory settings and subsequent restart. This
condition is signaled by the orange flashing of the led for 3 seconds as follows:
ON OFF ON OFF …..
300 ms 300 ms 300 ms 300 ms …..
3CONNECTION DIAGRAMS
I/O extension
port
Figure 1 Figure 2
DY GPS
2CSM441046D0201
ABB S.p.A
V.le dell’Industria 18
20010 Vittuone (MI) - Italy
Tel. +39 02 2415 0000
https://new.abb.com/low-voltage
© Copyright 2019 ABB S.P.A . All rights reserved.
We reserve the right to make technical changes or modify
the contents of this document without prior notice.
Installation Manual


Produkt Specifikationer

Mærke: ABB
Kategori: Ikke kategoriseret
Model: DY GPS

Har du brug for hjælp?

Hvis du har brug for hjælp til ABB DY GPS stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret ABB Manualer

ABB

ABB FW/S 8.2.1 Manual

18 September 2024
ABB

ABB S750DR-QA Manual

24 August 2024
ABB

ABB US/U 12.2 Manual

9 August 2024
ABB

ABB DY GPS Manual

30 Juli 2024
ABB

ABB DWS Manual

25 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024