Acratech Leveling Base 1170 Manual
Læs nedenfor 📖 manual på dansk for Acratech Leveling Base 1170 (2 sider) i kategorien Stativ. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
ACRATECH INC.
QUALITY PRECISION PRODUCTS
CAUTION: READ ALL INSTRUCTIONS BEFORE INSTALLING YOUR NEW
LEVELING BASE.
Thank you for purchasing the Acratech leveling base. Your new leveling base is
manufactured using the finest materials and workmanship. With proper care your
leveling base should last for many years.
The main adjustment knob and is used to tighten and loosen the ball so you can
adjust the leveling base. The knob is often only partially loosened so it will
maintain a controlled amount of friction or tension on the ball. The smaller knob is
preset and cannot be adjusted.
INSTALLING YOUR LEVELING BASE ON YOUR TRIPOD
1) If the threaded hole in the bottom of your new leveling base is larger in
diameter than the threaded stud on top of your tripod, then install the
brass reducer bushing provided. To do this you should use a small coin to
hand tighten the reducer bushing to moderate tightness. Measure the
length of the bolt sticking out of your tripod where you are going to install
your new Leveling Base. It should stick up at least ¼ in (6mm) and be no
longer than 3/8 in (9.5mm), if the bolt is too long it must be shortened
(Acratech can do this for a minimal charge).
2) Being careful not to cross thread, slowly tighten your new leveling base
onto your tripod “firmly hand tight”.
3) After installing your new leveling base, CAREFULLY make sure that it is
not interfering or binding on any part of your tripod. IF ANY
INTERFERING OR BINDING OCCURS, REMOVE THE LEVELING BASE
AND CONTACT ACRATECH BEFORE CONTINUING.
Produkt Specifikationer
| Mærke: | Acratech |
| Kategori: | Stativ |
| Model: | Leveling Base 1170 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Acratech Leveling Base 1170 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Stativ Acratech Manualer
12 August 2024
12 August 2024
Stativ Manualer
- Stativ SilverCrest
- Stativ Sony
- Stativ Easypix
- Stativ Asus
- Stativ Livoo
- Stativ Nikon
- Stativ Kodak
- Stativ Hama
- Stativ Trust
- Stativ Laserliner
- Stativ König
- Stativ Bresser
- Stativ Rollei
- Stativ DJI
- Stativ Godox
- Stativ Omnitronic
- Stativ Carson
- Stativ Celestron
- Stativ Zhiyun
- Stativ Rode
- Stativ AVerMedia
- Stativ Marshall Electronics
- Stativ GVM
- Stativ Sachtler
- Stativ Vortex
- Stativ Testo
- Stativ Barska
- Stativ ARRI
- Stativ Vinten
- Stativ Eurolite
- Stativ Kessler
- Stativ Proaim
- Stativ Manfrotto
- Stativ Kogan
- Stativ Joby
- Stativ Levenhuk
- Stativ Gravity
- Stativ Drift
- Stativ Magnus
- Stativ Konig & Meyer
- Stativ Neewer
- Stativ Easyrig
- Stativ REVO
- Stativ Glide Gear
- Stativ Miller
- Stativ Sky-Watcher
- Stativ Square Jellyfish
- Stativ Fidlock
- Stativ Robus
- Stativ Vello
- Stativ Benro
- Stativ Sunpak
- Stativ Slik
- Stativ Libec
- Stativ Gitzo
- Stativ Velbon
- Stativ Ultimate Support
- Stativ Oben
- Stativ Moza
- Stativ Vanguard
- Stativ Dorr
- Stativ Winegard
- Stativ Camgear
- Stativ Ulanzi
- Stativ Flycam
- Stativ Sirui
- Stativ ProMediaGear
- Stativ IOptron
- Stativ Mantona
- Stativ Olloclip
- Stativ Cullmann
- Stativ IFootage
- Stativ FeiYu-Tech
- Stativ FeiyuTech
- Stativ Hohem
- Stativ MOVE'N SEE
- Stativ On Air
- Stativ Kaiser Fototechnik
- Stativ Slidekamera
- Stativ FLOWCINE
- Stativ SteadiCam
- Stativ Fat Gecko
- Stativ 3 Legged Thing
- Stativ FLM
- Stativ Peak Design
- Stativ Studio Assets
- Stativ E-Image
- Stativ Tiltall
- Stativ MotoCrane
- Stativ Really Right Stuff
- Stativ HPRC
- Stativ Cartoni
Nyeste Stativ Manualer
14 December 2024
14 December 2024
12 December 2024
12 December 2024
12 December 2024
12 December 2024
12 December 2024
12 December 2024
11 December 2024
11 December 2024