Aerohive AP121 Manual

Aerohive Adgangspunkt AP121

Læs nedenfor 📖 manual på dansk for Aerohive AP121 (1 sider) i kategorien Adgangspunkt. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Locking the Device

Aerohive QuickStart

for the AP121 and AP141

This guide explains how to set up an Aerohive AP121 or AP141 access point (previously

named HiveAP 121 or HiveAP 141) so it can make a network connection to HiveManager,

and how to mount it on a ceiling or wall. (The AP141 with articulated antennas is shown in the

following illustration, but the instructions apply equally to both models.) To register, get the

latest product documentation (including translations of select documents), see compliance

information, and download software updates, visit www.aerohive.com/support.

AP121

3After you cable the AP to an Ethernet network and power it on, it automatically tries to

get its network settings through DHCP and contact HiveManager. This process takes about

ve minutes. When you see the AP listed on the All Devices Monitor page in the section of

the HiveManager GUI, the initial setup is complete and you can begin managing the AP

through HiveManager.

If the AP does not appear in the HiveManager GUI after about ten minutes, see the

Aerohive product documentation and computer-based training modules to understand

how the AP tries to contact HiveManager and what you can do to help establish a

connection. These items are available for free at www.aerohive.com/techdocs.

The status indicator on the lower left corner of the device shows the following activity states:

• Dark: Power is off, or the indicator has been disabled.

• Amber(ashing): The device is performing a rmware upgrade. Do not power off the device

during this process.

• Amber(solid): This indicates that the CAPWAP connection has not been successfully

established, or the device is booting up or shutting down.

• White: The device is powered on and operating properly, and has made a successful

CAPWAP connection through the ETH0 interface.

Aerohive® is a U.S. registered trademark of Aerohive Networks, Inc.

P/N 330078-04 Rev. A

Using the rail mount bracket, you can mount the AP121 or AP141 to the tracks of a dropped

ceiling grid. Using the mounting plate, you can mount it to any at surface that can support its

weight (AP121: 11.6 oz or 0.36 kg; AP141: 13.5 oz or .42 kg). Both mounting options are explained

below. (The AP121 is shown in these illustrations, but the instructions apply to both models.)

Mounting the AP121 and AP141

To mount the AP121 or AP141 to a standard 15/16"-wide track (2.38 cm) in a dropped ceiling, use

the rail mounting bracket that ships with the AP. You also need a drill and—most likely—a ladder.

Note: Aerohive also offers a mounting kit for 9/16" (1.34 cm) -wide, and 15/16" (2.38 cm) -wide

recessed tracks for AP121, AP141, AP330 and AP350 models (AH-ACC-9-16-CLIP-300-100,

and AH-ACC-15-16-CLIP-300-100).

Nudge the ceiling tiles slightly away from the track to clear some space, and then attach the

appropriate rail mounting bracket to the ceiling track. When you have the mounting bracket in

the correct location, cut or drill a hole in the ceiling through which you can then pass the Ethernet

and power cables.

With the cables connected, attach the AP to the mounting bracket as shown below to complete

the installation. For the AP141, attach the articulated antennas and, for optimal reception, align

them according to the congurations shown in Aligning AP141 Articulated Antennas.

Press the mounting bracket upward against the ceiling track so that the track

contacts the two pressure tabs and pushes them ush with the plate.

Rotate the mounting bracket until the two

pressure tabs click into place, gripping the

ceiling track.

With the AP upside down, align the two V-shaped tabs and the security tab extension on

the mounting bracket with the tab slots and security tab slot on the AP, and then press the

AP upward until it snaps into place.

When you are done, adjust the ceiling tiles into their former position.

You can use the mounting plate to attach the AP to any surface that supports its weight (less than

1 lb or .45 kg for either device), and to which you can screw or nail the plate. First, attach the

plate to the surface. Then, in the space not covered by the L-shaped mounting plate, drill a hole

in the wall so that you can pass the cables through to the AP. Finally, connect the cables to the

device, attach the device to the plate, and—for the AP141—attach the articulated antennas.

With the two exible V-shaped tabs at

the sides of the plate extending away

from the surface, attach the mounting

plate to a secure object such as a wall,

ceiling, post, or beam.

Cut or drill a hole in the wall in the space

not covered by the L-shaped mounting

plate, pass the cables through to the AP,

and connect them. (You can also run the

cables along the wall to the AP instead

of through a hole.)

Depending on how the AP is powered

and how it connects to the network,

connect a power cable and one or two

Ethernet cables. (The cables are not

shown in the illustration.)

Align the tabs and security tab extension

on the mounting plate with the tab slots

and security tab slot on the AP.

Push the AP against the mounting plate

until the tabs click inside the tab slots.

For the AP141, attach the articulated

antennas and orient them as described

in .Aligning AP141 External Antennas

Note: There are various holes through

which you can screw or nail the

plate in place. Choose the two or

three that best suit the object to

which you are attaching it.

Mount the AP on a wall as explained below.

2 3

You can secure the device using a Kensington lock. You and also lock the AP to the mounting

bracket or mounting plate using the security screw or slotted screw included with the mounting

kit. To use a Kensington lock, loop the cable attached to the lock around a secure object, insert

the T-bar component of the lock into the device lock slot on the AP, and then turn the key to

engage the lock mechanism.

To lock the AP to the mounting plate or bracket with the security screw, you will need a drilled

spanner insert bit for size #6 security screws and a screwdriver that will accept the bit. The

correct bits are available from Aerohive in sets of three for AP121, AP141, AP330 and AP350

models (AH-ACC-SEC-BIT-330-350-3PK). To use the security screw, refer to the illustration below.

To use the slotted screw, you will need a at-blade screwdriver.

Surface Mount

(Bird's eye view with

ceiling tiles removed and

the ceiling track shown as

transparent for clarity)

Rail mounting

bracket

Ceiling track

CLICK!

In the open space not covered by the L-shaped

mounting bracket, drill a hole in the ceiling tile

(not shown). Then pass one or both Ethernet

cables through the hole, and if you plan to

supply power from an AC power source,

pass the power cable through as well. Finally,

connect the cables to the AP.

StatusIndicator

Switch

DHCP

Server

Firewall

Internet

Some other network devices (They

might all be incorporated in the same

device, such as a router or firewall.)

Ethernet

cable

2If the switch provides

PoE (Power over

Ethernet), cabling the

AP to the switch will

cause the AP to power

on in a few seconds.

If the switch does not

provide PoE, use the

AC/DC power adaptor

(available as an

accessory) to connect

the AP to a 100-240 AC

power source.

ETH0

Connect a standard

Ethernet cable with

RJ-45 connectors

from ETH0 on the AP

to a switch.

Attach the antennas to the 5 GHz 5 GHz

connectors (marked on the chassis)...

and the antennas to the 2.4 GHz

connectors.2.4 GHz

Ceiling installation Wall installation

CeilingMount

AligningAP141ExternalAntennas

For optimal reception, align the antennas on the AP141 using one of the congurations shown:

Straight

90°

45°

90°

(Side view)

V-shaped tab

Security tab slot

extension

Tab slot

Security tab slot

V-shaped tab Insert the security screw

through the hole in the

chassis. Use a screwdriver with

a drilled spanner bit to fasten

the screw to the security tab

extension on the mounting

plate or rail mounting

bracket.

Turn clockwise to tighten

Mounting plate

Security screw

Screwdriver

Security tab

extension

Device lock slot

Security tab

slot

Straight

Security screw hole

Tab slot

Security tab extension

V-shaped tab V-shaped tab

(Bird’s eye view)

Security tab slot

Wall

AP141

Produkt Specifikationer

Mærke:	Aerohive
Kategori:	Adgangspunkt
Model:	AP121

Har du brug for hjælp?

Hvis du har brug for hjælp til Aerohive AP121 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Adgangspunkt Aerohive Manualer

Aerohive AP330 Manual

15 August 2024

Aerohive AP121 Manual

12 August 2024

Aerohive AP370 Manual

12 August 2024

Aerohive AP130 Manual

12 August 2024

Aerohive AP1130 Manual

10 August 2024

Aerohive AP170 Manual

10 August 2024

Aerohive AP230 Manual

7 August 2024

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

16 December 2024

15 December 2024

15 December 2024

15 December 2024

15 December 2024

15 December 2024

Vimar 14195.SL Manual

15 December 2024

Vimar 20195.B Manual

15 December 2024

Vimar 19195.B Manual

15 December 2024

TP-Link Festa F65-Outdoor Manual

11 December 2024