Alphacool ES Distro Plate C1 Manual

Alphacool Ikke kategoriseret ES Distro Plate C1

Læs nedenfor 📖 manual på dansk for Alphacool ES Distro Plate C1 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
ALPHACOOL INTERNATIONAL GMBH, MARIENBERGER STRAßE 1, 38122 BRAUNSCHWEIG SUPPORT: +45 (0) 531 28874 0 FAX +45 (0) 531 28874 22, E-MAIL: , , INFO@ALPACOOL.COM
GENERAL MANAGERS: ANDREAS RUDNICKI, NATHANAEL DRAHT, FABIAN NOELTE.
WEEE-REG.-NR.: DE 544444, TRADE REGISTER: AMTSGERICHT BRAUNSCHWEIG HRB 202390, VAT.ID.NR.: DE27058421, TAX NUMBER: 13/207/02047 02092020/1609
Alphacool ES Distro Plate C1
EN
ACCESSORIES
DE
ZUBEHÖR
FR
ACCESSOIRES
2x Screw plug Verschlussschraube Bouchon à vis / /
Read the safety instructions before starting
the installation.
Lisez les instructions de sécurité avant de
commencer l‘installation.
MOUNTING
LE MONTAGE
1.
In the fittings are all connections to each other. This
way different possibilities can be realized. Make sure
that all unused connections are closed with screw
plugs.
Dans les pièces de raccordement, toutes les connexions
sont reliées entre elles. De cette façon, différentes
possibilités peuvent être réalisées. Assurez-vous que
toutes les connexions non utilisées sont fermées par des
bouchons à vis.
2.
Mount the distributor in a free space in the housing.
There are two mounting options available. The position
of the screws is shown in the detailed drawing.
1. mount the distributor with the M3x4
screws.
2. you use the 5mm hole.
Alphacool ES housings are prepared for mounting the
distributors. For other housing manufacturers
in both cases it is very likely that you will have to drill
the holes in your housing. Be careful not to leave any
peeps in the case and damage the hardware. Alphacool
does not assume any warranty for this.
Read the examples on the back side.
Installez le distributeur dans un espace libre du boîtier.
Deux options de montage sont disponibles. La position
des vis est indiquée dans le dessin détaillé.
1. monter le distributeur avec les vis M3x4.
2. vous utilisez le trou de 5 mm.
Les boîtiers Alphacool ES sont préparés pour le montage
des distributeurs. Pour les autres fabricants de logements
dans les deux cas, il est très probable que vous deviez
percer les trous de votre logement. Faites attention à ne
pas laisser de traces dans le boîtier et à ne pas
endommager le matériel. Alphacool n'assume aucune
garantie à cet égard.
Lisez les exemples au verso.
EN: Use the screw plug tool.
DE: Nutzen Sie das
Verschlussschrauben-Tool.
FR: Utilisez l'outil de bouchage
à vis.


Produkt Specifikationer

Mærke: Alphacool
Kategori: Ikke kategoriseret
Model: ES Distro Plate C1

Har du brug for hjælp?

Hvis du har brug for hjælp til Alphacool ES Distro Plate C1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Alphacool Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer