Aluratek ABAS01F Manual
Aluratek
Bluetooth modtager
ABAS01F
Læs nedenfor 📖 manual på dansk for Aluratek ABAS01F (1 sider) i kategorien Bluetooth modtager. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
Package Contents Product Highlights Product Application
Operation Operation
WARNING!!! This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by whatever measures may be
required to correct the interference.
Radio and TV Interference Statement
qsg Q10496 Copyright © 2018 Aluratek, Inc. All Rights Reserved.
aluratek.com
model ABAS01F
Quick Start Guide
AirStream Universal Bluetooth Audio Transmitter
Technical Support and Warranty
If you need further assistance, please contact the Aluratek support department for
troubleshooting prior to returning this device.
E-mail: support@aluratek.com
Web: www.aluratek.com/helpdesk
Local (Irvine, CA): 714-586-8730
Toll free: 1-866-580-1978
Control Functions
Function Operation
Power ON When OFF, press and hold the Power Button for 3 seconds until
the blue LED flashes
Pairing
When OFF, press and hold the Power Button for 5 seconds or press
the Power Button once in standby mode
(LED flashes red and blue)
Power OFF When ON, press and hold the Power Button for 3 seconds until
the red LED flashes
Pairing
Please make sure the device supports A2DP profile. The pairing procedure will vary
depending on the actual device. Please refer to the user guide of your device for detail
instruction. The general pairing procedures are as follows:
1. Make sure ABAS01F is turned OFF
2. Activate your device’s Bluetooth function and set your device to pairing mode.
3. Activate ABAS01F pairing mode by press and holding the power button for 5 seconds
(If ABAS01F has not been paired to any device before, it will go into pairing mode after
it is powered ON)
4. ABAS01F and your Bluetooth device will pair automatically
5. After connecting successfully, the blue LED will stay on
Note: After the initial pairing of your Bluetooth device with ABAS01F. It is recommend that you power on your
Bluetooth device first before you power on ABAS01F for subsequent uses for faster reconnection. If the device does
not reconnect, you may press the power button to speed up the process.
Your order has been carefully packaged and inspected. The following accessories should
be included in your package. Please inspect the contents of the package to ensure that
you have received all items and that nothing has been damaged. If you discover a problem,
please contact us immediately for assistance.
USB Charging Cable Seat Adapter
Operation
LED Indicators
LED Indicator Status
Solid Red LED Charging
Flashing Red and Blue Pairing Mode
Low battery
Successfully paired
LED OFF
Solid Blue LED
Powered on and in standby mode but not paired with
Bluetooth devices
Flashing Blue Twice
(Every 5 Seconds)
Flashing Red
Power OFF / Fully charged if connected to a power source
Note: For first time use, once powered on, the adapter will automatically enter pairing mode. After 10 seconds,
the LED will flash blue and red. Please follow the instructions below on how to pair.
Charging The Battery
The battery is not fully charged and it is highly recommended that you charge ABAS01F
before you begin using it.
Note: Using ABAS01F “out of the box” will not harm the device. You will experience
reduced battery life as the unit will not be fully charged.
Connect the larger USB end of the cable provided to your PC or USB power adapter or
powerbank (not included). Plug the smaller Micro USB to the charging port of ABAS01F.
Please charge the battery for a minimum of 3 hours. The red LED will be on while
charging. When charging is complete, the red LED will turn OFF.
Operation
Using ABAS01F With Power Connected
Here are the steps to follow if you want to use ABAS01F ABAS01F with power connected.
will stay in standby mode as long the power is connected so your Bluetooth device can
reconnect automatically after you are within range.
1. Make sure ABAS01F is turned OFF
2. Connect the larger USB end of the cable provided to your powerbank, power adapter
or USB port at the seat and the smaller end to the charging port to ABAS01F
3. Follow the pairing instruction to pair your device if it is not paired already
Operation
Micro USB Charging Port
3.5mm Cable
LED Indicator
Power Button
OR
In-flight
Display Monitor
Transmit audio up
to 33 feet (10 m)
Bluetooth
Headphones
Airline Seat
Bluetooth
Headphones
Bluetooth
AirPods
Pair With Two Devices At The Same Time
The adapter is able to pair with two Bluetooth stereo headphones/speakers at the same time.
1. Follow the previous instructions in the “Pairing” section to pair ABAS01F with your first device.
2. Turn off the Bluetooth function on your first device
3. Activate your second device’s Bluetooth function and set your device to paring mode
4. Tap the Power Button once on ABAS01F to pair and connect to your second device
5. Turn on the Bluetooth function on your first device. In approximately 30 seconds, the
device will automatically connect
Note: If the second device does not auto connect, please press the power button once to reconnect.
Aluratek warrants this product against defect in material or workmanship for 1 YEAR
from the date of purchase.
For more information, please visit: https://aluratek.com/warranty-return-policy
You can register your product online at: https://aluratek.com/product-registration
Troubleshooting
If both red and blue LED lights stays on or if the device does not respond to pressing and
holding the power button, follow below steps to reset the transmitter.
1. Press and hold the power button
2. While holding the power button, connect the USB charging cable which is connected
to either a power adapter or computer
3. Release the power button when the red and blue LED lights are flashing alternately
4. The transmitter is now reset and ready to pair again
Optional Seat
Adapter (included)
Supports dual streaming.
Two devices can be used
simultaneously.
Produkt Specifikationer
| Mærke: | Aluratek |
| Kategori: | Bluetooth modtager |
| Model: | ABAS01F |
Har du brug for hjælp?
Hvis du har brug for hjælp til Aluratek ABAS01F stil et spørgsmål nedenfor, og andre brugere vil svare dig
Bluetooth modtager Aluratek Manualer
16 August 2024
12 August 2024
12 August 2024
12 August 2024
10 August 2024
10 August 2024
9 August 2024
9 August 2024
8 August 2024
8 August 2024
Bluetooth modtager Manualer
- Bluetooth modtager Hama
- Bluetooth modtager T'nB
- Bluetooth modtager König
- Bluetooth modtager Bose
- Bluetooth modtager Focal
- Bluetooth modtager Terratec
- Bluetooth modtager StarTech.com
- Bluetooth modtager Lindy
- Bluetooth modtager Legrand
- Bluetooth modtager Audioengine
- Bluetooth modtager Bigben Interactive
- Bluetooth modtager Naxa
- Bluetooth modtager Autovision
- Bluetooth modtager Monoprice
- Bluetooth modtager Oehlbach
- Bluetooth modtager Wavemaster
Nyeste Bluetooth modtager Manualer
30 August 2024
30 August 2024
30 August 2024
28 August 2024
21 August 2024
19 August 2024
18 August 2024
18 August 2024
17 August 2024
16 August 2024