Analog Way EXT-HDMI20-OPT-TX Manual

Analog Way AV forlænger EXT-HDMI20-OPT-TX

Læs nedenfor 📖 manual på dansk for Analog Way EXT-HDMI20-OPT-TX (2 sider) i kategorien AV forlænger. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

EXT-HDMI20-OPT-TX

EXT-HDMI20-OPT-RX

Further Informaon

www.analogway.com

January 2021

QSG EXT-HDMI20-OPT-TX/RX

Code : 140209

Important Safety Instrucons

Please read the supplied safety

instrucon document before using the

product and keep it available for future

reference.

CAUTION - The use of controls or adjustments or any performance of procedures

other than those specied herein may result in hazardous radiaon exposure.

Introducon

Thank you for choosing Analog Way EXT-HDMI20-OPT-TX and RX opcal extenders.

The EXT-HDMI20-OPT-TX and EXT-HDMI20-OPT-RX are HDMI 2.0 compable ber

opcal extenders providing uncompressed signal extension with embedded audio

to a range of 2500 m (8000 .) over a single mulmode ber cable connecon.

Its rugged, solid metal casing provides excellent cooling and maximum reliability.

These ber opcal extenders are also compable with Analog Way’s LivePremier™

HDMI 2.0 over ber output card (ref. ACC-AQL-OUT-HDMI-FBR) and HDMI 2.0 over

ber input card (ref. ACC-AQL-IN-HDMI-FBR).

Box Contents

Transmier / Receiver

module

5V DC adaptor with

interchangeable plugs

Safety and Warranty Info,

Quick Start Guide

HDMI plug HDMI connector plug for HDMI audio and video signal

transmission. The following protocols and features are

supported:

HDMI 1.x and HDMI 2.0 audio/video - the module

automacally selects between HDMI 2.0 and HDMI 1.x

based on the type of the signal source or sink device.

HDCP 1.4 or HDCP 2.2 encrypon - the module

automacally selects between HDCP 1.4 and HDCP 2.2

based on the type of the signal source or sink device.

EDID, CEC, and HDCP transparent.

Loopholes Loopholes for self-fastening belts for mounng. See the

details in the Mounng Opons secon.

USB-A plug Standard USB-A plug to USB-compable (1.1 or higher)

host port. The following features are supported:

The receiver and transmier can be fully powered

from the USB port. This capability is available even if

the aached USB host port is “power only”.

For transmier only: USB power is fully compable

with HDMI power. The transmier performance will

not degrade if the HDMI power and USB power are

available simultaneously. Similarly, connecng USB

power and HDMI power simultaneously will not cause

any damage to the aached USB host or HDMI video

source.

Boom View - Transmier / Receiver

SC ber

connector

SC ber opcal connector. Connect a mulmode ber

opcal cable between the transmier and the receiver. The

following features are supported:

All communicaon, including audio and video

transmission, and HDCP over one opcal ber.

The connector supports open ber detecon with high

speed laser shutdown.

Status LED Indicates the current status of the transmied or received

opcal and HDMI signals, and the HDCP-encrypon.

OFF Module is not powered.

BLINKING (red) No ber link is detected.

BLINKING (yellow) Fiber link is established, but no

HDMI cable is detected (5V is not

detected on the source or hotplug

is not detected on the sink).

ON (yellow) Fiber link is established, cable is

connected, but no HDMI signal.

BLINKING (green) Fiber link is established, signal is not

HDCP-encrypted.

ON (green) Fiber link is established, signal is

encrypted with HDCP 1.4.

Mounng Opons

The ergonomic enclosure provides two possible methods for mounng the device.

Opon 1 - Mounng the device to a rack shelf

The transmier and the receiver

modules have two mounng holes

each with inner threads on the two

narrow sides. The distance between

the holes is 67,5 mm.

Fasten the device by the screws

packaged with the following,

compable mounng accessories:

Under-desk mounng kit

Under-desk double mounng

kit

1U high rack shelf

The required screw type: PZ at

head (M3x6mm)

To order mounng accessories please contact your sales representaves

Opon 2 - Mounng the device using self-fastener

Use the two e-down loops of the enclosure to thread through self-fastener. The

modules can be mounted to basically any installaon point, for example rack frames.

In case of installaon to a truss, always x the module with a safety wire as well.

Opon 3 - Mounng the device to the OPT-POWERTRAY

The OPT-POWERTRAY is a 1RU size housing accessory which can enclose up to 16

pcs EXT-HDMI20-OPT-TX/RX units, also providing power source for every installed

device. Three dierent models are available:

SC model: built with 8x SC duplex ber opcal connectors for 16x mulmode

SC ber opcal cables.

NTD model: 4x Neutrik NO2-4FDW-A connectors for 4x Neutrik opcalCON

DUO series cables or 8x LC ber opcal cables.

NTQ model: 4x Neutrik NO4FDW-A connectors for 4x Neutrik opcalCON QUAD

series cables.

BLINKING (blue) Fiber link is established, HDCP 2.2

inializaon is in progress.

ON (blue) Fiber link is established, signal is

encrypted with HDCP 2.2.

Troubleshoong

The following LED status mean incorrect extender modes. It can

happen when the USB-A plug of the extender is connected to a USB

connector where the data transmission is enabled.

Soluon: Use the supplied power adaptors.

BLINKING (pink) The device is in bootloader mode.

ON (pink) The device is in bootloader mode

and bootloader is congured by the

USB host.

Connecng Steps

Follow the installaon steps to connect the extenders between the source and

sink devices:

OPTM

Connect the multimode fiber optical cable to the SC fiber connector

of the receiver.

HDMI

Connect the to the input port of the sink HDMI plug of the receiver

device. The extender reads the EDID from the device (seamless

switcher input, projector, monitor, etc), and outputs the video signal

according to the set resolution.

Power

Power on the receiver by choosing one of the powering options

below:

Connect the USB plug of the receiver to the power adaptor.

Connect the USB plug of the receiver to the USB connector of the

sink device.

OPTM

Connect the multimode fiber optical cable to the SC fiber connector

of the transmitter.

HDMI

Connect the HDMI plug of the transmitter to the output port of the

source device (e.g. PC).

Power

Finally power on the transmitter by choosing one of the powering

options below:

Connect the USB plug of the transmier to the power adaptor.

Connect the USB plug of the transmier to the USB connector of

the source device.

Connect the to the output port HDMI plug of the transmier

of the source device (e.g. PC). If the HDMI source device is able

to provide enough 5V DC current (500mA), there is no need for

external 5V DC power. The extender is powered immediately

when the source device is switched on.

Check the Status LED. When the connection has been made successful,

the LEDs on the transmitter and receiver will appear green or blue

depends on the HDCP-encryption.

EXT- H M

0 O - R

Statu

llow:

o H

ed/Pi n k: No

Gree

CP 1.4

lue:

2.2

DMI

.0 OU

RECEIVER

ULT

CLAS

S 1

LASE

Sn: 15100001

LED StatusYello w: No H DMI

Red/Pink: No FiberGreen: HDC P

1.4

Blue: HDCP 2.2

HDMI 2.0 IN

TRANSMITTER

MUL

TIMODE

SC OUT

Sn: 15100001

CLASS 1LASER

PRODUCT

EXT-HDMI

20-OPT-TX

Made i

n E

Powe

red

y Ligh

tware

EX HMI20-OP TXT- T-

transmitter

PC EX HMI20-OP RXT- T-

receiver

4K TV

Power adaptor

OPTM

Power

HDMI

in EU,

Pow

ere

d b

y Li

ghtware

EXT-HDMI20-O PT-RX

Safety and

Warranty

Info

Quick

Start

Guide

CLASS 1 LASER PRODUCT

CAUTION - CLASS 3R INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT

EYE EXPOSURE.

LED St at us

Yellow: No HDMI

Red/Pink: No Fiber

Green: HDCP 1.4

Blue: HDCP 2.2

HDMI 2.0 OUT

MU IMODELT

SC IN

CLASS 1

LASER

PRODUCT

Sn: 15100001

Made in EU,

EXT-HDMI20-OPT-TX

TRANSMITTER

Produkt Specifikationer

Mærke:	Analog Way
Kategori:	AV forlænger
Model:	EXT-HDMI20-OPT-TX

Har du brug for hjælp?

Hvis du har brug for hjælp til Analog Way EXT-HDMI20-OPT-TX stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

AV forlænger Analog Way Manualer

Analog Way EXT-DP12-OPT Manual

23 December 2024

Analog Way EXT-HDMI20-OPT-TX Manual

23 December 2024

Analog Way HMH-RX110 Manual

25 November 2022

Analog Way HMH-TX110 Manual

25 November 2022

AV forlænger Manualer

Nyeste AV forlænger Manualer

Comprehensive CHE-HDWP85UD Manual

23 December 2024

Comprehensive CHE-HDBTWP121K Manual

23 December 2024

Camplex CMX-FMCH002 Manual

23 December 2024

MuxLab 500086 Manual

23 December 2024

Camplex CMX-FMCH003 Manual

23 December 2024

Comprehensive CHE-HDBT250 Manual

23 December 2024

Sescom SES-X-FA8LTT01 Manual

23 December 2024

Adder Link XD150FX Manual

23 December 2024

Adder Link XD612 Manual

23 December 2024

Adder Link XD641 Manual

23 December 2024