Assault Fitness Bike Elite Manual

Assault Fitness Fietstrainer Bike Elite

Læs nedenfor 📖 manual på dansk for Assault Fitness Bike Elite (2 sider) i kategorien Fietstrainer. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Left Pedal (016-1)

Main Frame

Seat / Slide Assembly (A)

Seat Slide Cover - Front (349)

Console (314)

Console Mast (312)

Console Mast Cover

Mounting Plates (315)

Speed Sensor Cable - Lower (384)

Speed Sensor Cable - Upper (313a)

Speed Sensor Cable - Upper (313b)

Console Mast Covers (316)

Right Pedal (015-1) Front Stabilizer (302-A)

Rear Stabilizer (303-A)

Handlebar - Left (323-A)

Handlebar - Right (322-A)

Foot Pegs (326)

Handlebar Pivot Covers (324)

Seat Slide Reinforcement

Plate (432)

ASSEMBLY TOOLS

4mm

Hex Wrench

(415)

2.5mm

Hex Wrench

(416)

6mm

Hex Wrench

(414)

17mm/ 21mm

Open-Ended

Wrench

(413)

Socket Head Hex Screw

M8 x 1.25 x 12mm (325)

Button Head Hex Screw

M4 x 10mm (345)

Nylock Nut

M10 (329)

Socket Head Hex Screw

M8 x 1.25 x 20mm (304)

HARDWARE DESCRIPTION DRAWING QUANTITY

Flat Washer

Ø19.0OD x Ø8.5ID x 1.2t (305)

Flat Washer

Ø22OD x 10.5ID x 2.0t (328)

Socket Head Hex Screw

M8 x 1.25 x 25mm (317)

Socket Head Hex Screw

M3 x 0.5 x 8mm (319)

17mm

Open-Ended

Wrench

(424)

Front Stabilizer

(302-A)

Rear Stabilizer

(303-A)

305 304

317

319

316

315 317

315

316

319

314a

313a

313b

384

314

312

318

Main Frame

Left Pedal (016-1)

Pop-Pin (369)

Right Pedal (015-1)

Seat Post Assembly

(336-A)

Seat / Slide Assembly (A)

Seat Slide Cover Assembly

- Front (349-A) 4mm Button Head

Hex Screw (345)

Pop-Pin (338)

Stabilizer Leveling Foot

326 325 324

329 328 323-A

324322-A 325 326

329328

Linkage Arm Pivot Pin

Assembly Step One:

Front & Rear Stabilizer Installation

• With the assistance of a second person,

raise front portion of the Main Frame

so the unit rests on the rear stabilizer

receiver and the seat slider.

• While supporting the unit, align the

Rear Stabilizer (303-A) with the

stabilizer receiver of the .Main Frame

• Place one onto #305 M8 Flat Washer

each of the #304 M8 x 20mm Socket

Head Hex Screws. Loosely thread

the M8 Socket Head Hex Screw/M8

Flat Washer Assembliess through the

underside of the Rear Stabilizer (303)

and into the . Repeat these Main Frame

steps for the Front Stabilizer (302-A)

and tighten the screws rmly with the

provided 6mm Hex Wrench.

• With assistance, safely return the

ASSAULTBIKE ELITE to an upright

position.

Assembly Step Three – Handlebars

• While supporting the the Right

Handlebar Assembly (322-A), align

the lower pivot of the handlebar and

slide it onto the Linkage Arm Pivot

Pin #328 Flat Washer. Install a and

#329 M10 Nylock Nut and tighten

rmly.

• Rotating the around Right Handlebar

the lower pivot, align the upper pivot

pin with the receiver on the main

frame. Thread the pivot pin into the

frame with a clockwise rotation and

tighten rmly with the provided

wrench.

• Align one of the Handlebar Pivot

Covers (324) with the mounting holes

on the , and loosely Right Handlebar

thread the two #325 Cap Head Hex

Screws through the cover and into the

handlebar. Tighten rmly.

• Install a Foot Peg (326) onto the

handlebar pivot, rotating it clockwise.

• Slide the long, 6mm hex wrench

through the holes milled into the peg

and tighten rmly with a clockwise

rotation.

• Repeat the above steps for the left side.

ASSEMBLY

Introduction

• The ASSAULTBIKE ELITE requires only minor assembly. All tools required to complete the initial setup and

assembly have been included in the Assembly Hardware Kit.

• Remove the unit and all parts from the carton and packaging. Conrm all parts shown in the section above titled

As Shipped are included before attempting assembly of the ASSAULTBIKE ELITE.

Assembly Step Four – Seat Post, Pedals & Leveling the Unit

Assembly Step Two: Console Mast

• Remove the four from the backside of the #318 Phillips Screws

Console (314) Connect the Speed Sensor Cable and set aside.

(314a) Speed extending from the backside of the console with

Sensor Cable – Upper (313a) and carefully tuck the cable into

the . Console Mast (312)

• Align the mounting holes located in the back of the Console

(314) Console Mast (312) with the holes in the and loosely

thread the four through the console mast #318 Phillips Screws

and into the console. Tighten rmly.

• The Speed Sensor Cable - Upper (313) is pre-installed and

should be extending from the top and bottom of the Console

Mast Speed Sensor Cable – . Connect the lower end of the

Upper (313b) Speed Sensor Cable – Lower (384) with the .

• Align the Seat Slide Cover Assembly –

Front (349-A) with the forward edge of the

Seat / Slide Assembly (A) and mount it with

the two . #345 - 4mm Button Head Hex Screws

• Install the onto the Right Pedal (015-1) Right

Crank a few threads by hand with a clockwise

rotation of the axle. Insert the 6mm Hex Wrench

into the end of the Right Pedal (015-1) axle

inside of the crank arm and tighten rmly.

• The Left Pedal (016-1) axle threads are reversed,

meaning the axle rotates in the opposite

direction from most screws or bolts for installation. Engage the

rst few threads of the Left Pedal Left Crank axle into the by hand with a counter-clockwise rotation, then

tighten rmly with the 6mm Hex Wrench.

• Select a suitable space for operation of the ASSAULTBIKE ELITE. Move the unit to the desired location by raising

the rear stabilizer o the ground until the transport wheels touch the ground. Slowly push the unit into place.

Ensure there is 0.5 m (19.7 in.) of clearance on all sides of the bike.

• Ensure the unit is level and does not rock by adjusting the Stabilizer Leveling Feet. There are two feet on the

Front Stabilizer and two on the Rear Stabilizer. As a starting point, loosen each foot by threading the assembly

downward/clockwise, and then thread the locknuts downward (clockwise) against the foot base. Check the

unit for stability and make any adjustments as necessary. Once stable, lock the Stabilizer Leveling Feet in

place by tightening the jam nut upward/counter-clockwise, against the underside of the stabilizer to lock the

current position of each foot.

• Congratulations, your new ASSAULTBIKE ELITE is fully assembled and ready for use. Please read all included

information, user guides and warnings before use.

• Align the mounting plate for the Console Mast

(312) Main Frame with the mounting holes in the .

Carefully tuck the console connectors and cables

into the frame. Loosely thread two M8 x 25mm Cap

Head Hex Screws (317) Console Mast through the

Cover Mounting Plate (315) Console Mast and

(312) Main Frame and into the . Repeat the above

steps and install the #315 Console Mast Cover

Mounting Plate on the opposite side. Tighten all

four screws rmly with the 6mm Hex Wrench.

• Align one of the Console Mast Covers

(316) with the mounting holes in the

Console Mast Cover Mounting Plate

(315) #319 M4 and loosely thread two

Socket Head Hex Screws through the

one cover and into the plate. Repeat this

process for the opposite side, and tighten

all four screws.

• To raise the Seat Post Assembly

(336-A) Seat Post loosen the

Pop-Pin (369) and pull it

outward while sliding the seat

post upward. Release the pop-pin

and ensure the seat post has

positive engagement in one of

the eleven height positions.

• Align the channel in the

underside of the Seat / Slide

Assembly (A) with the rail on

the Seat Post Assembly (336-A)

and slide it all the way forward.

It may be necessary to loosen the

Seat Slide Adjuster Knob (338).

Part #23-AS-418 US-English v1.0 09-Oct-20

QUICK START

GUIDE

5803 Newton Drive, Carlsbad, California, USA 92008 Phone: 1.888.815.5559

For more information or questions regarding your equipment, please visit our website at www.assaulttness.com

Produkt Specifikationer

Mærke:	Assault Fitness
Kategori:	Fietstrainer
Model:	Bike Elite

Har du brug for hjælp?

Hvis du har brug for hjælp til Assault Fitness Bike Elite stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fietstrainer Assault Fitness Manualer

Assault Fitness Bike Classic Manual

31 August 2024

Assault Fitness Bike Elite Manual

31 August 2024

Fietstrainer Manualer

Nyeste Fietstrainer Manualer

Garmin Tacx Neo 2T Smart Manual

24 September 2024

Tacx Blue Matic T2650 Manual

17 September 2024

Tunturi E6 Manual

13 September 2024

Schwinn 590U Manual

8 September 2024

Matrix R50 XIR Manual

6 September 2024

Body Solid B5U Manual

5 September 2024

Body Solid ESB150 Manual

5 September 2024

Horizon GR7 Manual

5 September 2024

Wahoo KICKR Axis Manual

5 September 2024

Inspire IC2.2 Manual

5 September 2024