ATen PE0212A Manual
ATen
forlængelsesblok
PE0212A
Læs nedenfor 📖 manual på dansk for ATen PE0212A (3 sider) i kategorien forlængelsesblok. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/3
PE0112A/PE0112G/PE0212A/PE0212B/PE0212G PDU básica
Unité d'alimentation Basic PDU PE0112A/PE0112G/PE0212A/PE0212B/PE0212G PDU di base PE0112A/PE0112G/PE0212A/PE0212B/PE0212G
PE0112A/PE0112G/PE0212A/PE0212B/PE0212G Basis-PDU Блок питания Basic PE0112A/PE0112G/PE0212A/PE0212B/PE0212G
PE0112A/PE0112G/PE0212A/PE0212B/PE0212G Basic PDU www.aten.com www.aten.com
www.aten.com www.aten.com
www.aten.com www.aten.com
A
Hardware Review
1 Power Inlets
2 Circuit Breaker
3 Power Outlets
4 Grounding
B
Hardware Installation
The Basic PDU can be installed in a 1U confi guration on the side of a
rack. To rack mount the device, use the rack mounting brackets that
came with your device. The brackets can be mounted either near the
top and bottom of the back panel, or the top and bottom ends of the
device.
To set up an installation, refer to the installation diagrams (the numbers in
the diagram correspond to the numbered steps), and do the following:
1 Connect the Basic PDU's power cord to an AC power source.
2 For each device you want to connect, use its power cable to connect
from the device's AC socket to any available outlet on the Basic PDU.
Note: We strongly advise that you do not plug the Basic PDU into a multi
socket extension cord, since it may not receive enough amperage
to operate correctly. Once you have fi nished these installation steps,
you can turn on the Basic PDU and the connected devices.
AHardware Review
BHardware Installation
© Copyright 2018 ATEN® International Co., Ltd.
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved. All
other trademarks are the property of their respective owners.
This product is RoHS compliant.
Part No. PAPE-1223-M60G Printing Date: 05/2018
Basic PDU
Quick Start Guide
PE0112A/PE0112G/PE0212A/
PE0212B/PE0212G
ATEN NRGence™
Support and Documentation Notice
All information, documentation, fi rmware, software utilities, and
specifi cations contained in this package are subject to change without
prior notifi cation bythe manufacturer.
To reduce the environmental impact of our products, ATEN
documentation and software can be found online at
http://www.aten.com/download/
Technical Support
www.aten.com/support
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며,
가정외의 지역에서 사용하는 것을 목적으로 합니다.
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifi cations not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
Warning: Operation of this equipment in a residential environment could cause radio interference.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) this device mat not cause harmful interference, and(2) this device must accept any
interference received, including interference that may cause undesired operation.
Scan for
more information
2
1
31 2 4
Package Contents
1 Basic PDU
1 Power cord
1 User Instructions
Note: For safety reasons the equipment should be installed near the
wall socket outlet and the disconnect device (appliance coupler
on detachable power supply cord or plug on nondetachable
power supply cord) should be readily accessible
A
Présentation du matériel
1 Prises d'alimentation
2 Disjoncteur
3 Prises électriques
4 Mise à la terre
B
Installation du matériel
L'unité d'alimentation Basic PDU peut être installée dans une
confi guration 1U sur le côté d'un rack. Pour monter l'appareil en rack,
utilisez les supports de montage en rack fournis avec votre appareil.
Les supports peuvent être montés à proximité du haut et du bas du
panneau arrière ou sur les extrémités haute et basse de l'appareil.
Pour confi gurer une installation, consultez les diagrammes d'installation
(les chiffres du diagramme correspondent aux étapes numérotées) et
effectuez ce qui suit :
1 Connectez le cordon d'alimentation de l'unité d'alimentation Basic PDU
à une source d'alimentation CA.
2 Pour chaque appareil que vous souhaitez connecter, utilisez son câble
d'alimentation afi n de raccorder la prise CA de l'appareil à une prise
disponible sur l'unité d'alimentation Basic PDU.
Remarque : Nous vous conseillons vivement de ne pas brancher l'unité
d'alimentation Basic PDU dans une rallonge multiprises, car
elle pourrait ne pas recevoir un ampérage suffi sant pour
fonctionner correctement. Une fois ces étapes d'installation
terminées, vous pouvez allumer l'unité d'alimentation Basic
PDU et les appareils connectés.
A
Hardwareübersicht
1 Stromeingänge
2 Schutzschalter
3 Stromanschlüsse
4 Erdung
B
Hardwareinstallation
Die Basis-PDU kann in einer 1HE-Konfi guration an der Seite eines Racks
installiert werden. Zur Rackmontage des Gerätes verwenden Sie die mit
Ihrem Gerät gelieferten Rack-Montagehalterungen. Die Halterungen
können nahe der Ober- und Unterseite der Rückblende oder an den
oberen und unteren Enden des Gerätes montiert werden.
Beachten Sie zur Einrichtung einer Installation die Installationsabbildungen
(die Nummern in der Abbildung entsprechen den nummerierten Schritten)
und gehen Sie wie folgt vor:
1 Verbinden Sie das Netzkabel der Basis-PDU mit einer Steckdose.
2 Schließen Sie bei jedem Gerät, das Sie verbinden möchten, dessen
Stromkabel an den Netzanschluss des Gerätes und einen verfügbaren
Ausgang an der Basis-PDU an.
Hinweis: Wir raten dringend davon ab, die Basis-PDU an eine
Mehrfachsteckdose anzuschließen, da sie andernfalls
möglicherweise nicht mit einer ausreichenden Stromstärke
versorgt wird. Sobald Sie diese Installationsschritte abgeschlossen
haben, können Sie die Basis-PDU und die angeschlossenen
Geräte einschalten .
A
Vista preliminar del hardware
1 Entradas de alimentación
2 Disyuntor
3 Salidas de alimentación
4 Toma a tierra
B
Instalación de hardware
Se puede instalar la PDU básica en una confi guración de1 unidad en
el lateral de un bastidor. Para montar el dispositivo en un bastidor,
utilice los soportes de montaje en bastidor que se suministran con su
dispositivo. Se pueden montar los soportes cerca de la parte superior o
cerca de la parte inferior del panel posterior o los extremos superiores o
interiores del dispositivo.
Para confi gurar la instalación, consulte los diagramas de instalación (los
números del diagrama corresponden a los pasos enumerados),y realice lo
siguiente:
1 Conecte el cable de alimentación de la PDU básica a una fuente de
alimentación CA.
2 Para cada dispositivo que desea conectar, utilice el cable de
alimentación para conectar la toma de CA del dispositivo a cualquier
salida disponible de la PDU básica.
Nota: Recomendamos encarecidamente que no conecte la PDU básica
en un prolongador de múltiples tomas, p1-ya que posiblemente no
recibirá sufi ciente amperaje para operar de forma correcta. Una vez
que haya fi nalizado estos pasos de instalación, puede encender la
PDU básica y los dispositivos conectados.
A
Descrizione hardware
1 Ingressi di potenza
2 Interruttore automatico
3 Uscite di potenza
4 Messa a terra
B
Installazione dell'hardware
La PDU di base può essere installata in una confi gurazione 1U sul lato
di un rack. Per montare il dispositivo su rack, utilizzare le staffe di
montaggio del rack in dotazione con il dispositivo. Le staffe possono
essere montate vicino alle parti superiore e inferiore del pannello
posteriore o alle estremità superiore e inferiore del dispositivo.
Per l'installazione, fare riferimento agli schemi di montaggio (i numeri sullo
schema corrispondono a quelli della procedura) e procedere some segue:
1 Collegare il cavo di alimentazione della PDU di base a una presa di
corrente AC.
2 Per ciascun dispositivo che si vuole collegare, utilizzare il relativo cavo
di alimentazione per collegare la spina AC del dispositivo a una delle
prese disponibili sulla PDU di base.
Nota: Si raccomanda vivamente di non collegare lao PDU di base ad una
ciabatta, poiché potrebbe non ricevere l’amperaggio suffi ciente per
funzionare correttamente. Dopo avere completato le procedure di
installazione è possibile accendere la PDU di base ed i dispositivi
collegati.
A
Обзор аппаратного обеспечения
1 Входы питания
2 Прерыватель цепи
3 Электрические розетки
4 Заземление
B
Установка аппаратного обеспечения
Блок питания Basic можно установить в конфигурации 1U со
стороны стойки. Для монтажа устройства в стойке в комплекте
с устройством поставляются кронштейны для монтажа в стойке.
Кронштейны можно установить возле верхней и нижней части
задней панели либо возле верхней и нижней части устройства.
Для установки выполните следующие действия, руководствуясь
схемой установки (номера на схеме соответствуют номерам
действий):
1 Подключите шнур питания блока питания Basic к источнику
питания переменного тока.
2 Для подключения каждого из устройств подсоедините один
конец шнура питания к разъему переменного тока устройства,
а другой конец к любой свободной розетке на корпусе блока
питания Basic.
Примечание. Настоятельно рекомендуется не подключать блок
питания Basic к многорозеточным удлинителям,
т.к. в этом случае сила тока может оказаться
недостаточной для исправной работы. После
завершения установки можно включить блок питания
Basic и подключенные устройства.
Produkt Specifikationer
| Mærke: | ATen |
| Kategori: | forlængelsesblok |
| Model: | PE0212A |
Har du brug for hjælp?
Hvis du har brug for hjælp til ATen PE0212A stil et spørgsmål nedenfor, og andre brugere vil svare dig
forlængelsesblok ATen Manualer
19 August 2024
ATen Manualer
8 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
3 September 2024
3 September 2024