Audio-Technica AT150MLX Manual
Audio-Technica
DJ udstyr
AT150MLX
Læs nedenfor 📖 manual på dansk for Audio-Technica AT150MLX (2 sider) i kategorien DJ udstyr. Denne guide var nyttig for 41 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
Vector-Aligned stereo phono cartridges feature an original design
patented by Audio-Technica around the world. The key to this
mechanism is the two magnetic generators arranged in the shape of a
“V”. These two magnets are positioned precisely to match the positions
of the left and right channels in the stereo record groove. Major benefits
of the Vector-Aligned cartridge include outstanding channel separation,
very low distortion and superb tracking performance. Incorporating the
same essential merits as other Vector-Aligned models, the AT150MLX
features three additional technological advances:
Boron Cantilever. Its tiny, gold-plated boron cantilever provides an
extremely rigid yet lightweight platform to which the stylus is mounted.
Interestingly, the gold plating acts to damp what little resonance the
boron may produce.
MicroLine™ Stylus. The stylus used is of the latest and most
advanced design: the MicroLine™ stylus (Figure 1). More closely
resembling the cutter stylus than any previous design, this shape
produces better high frequency response with less wear or distortion
than with earlier configurations.
PCOCC Wire. A technologically advanced pure copper material is
used in Audio-Technica's exclusive “Paratoroidal Signal Generator”
(Figure 2). Together with the laminated core structure, which minimizes
loss in the high frequency region, this integrated paratoroidal generator
system operates at an efficiency significantly greater than conventional
cartridges. The use of PCOCC wire (Pure Copper by Ohno Continuous
Casting) perfects the performance of the advanced paratoroidal coil
design. A special high-temperature extrusion die produces copper with
virtually no transverse crystal barriers to impede signal transmission or
color sound. Thus, the coils of the AT150MLX transmit distortion-free
sound in which even the most subtle details are reproduced with clarity
and purity.
A mu-metal shielding plate between the left and right channels in the
generator system assure that the high level of channel separation
achieved is preserved at the cartridge output.
To further increase the accuracy of the AT150MLX's moving system,
Audio-Technica engineers have ensured against unwanted parasitic
vibration with an anti-resonance ceramic mounting base.
As a final attention to detail, even the output terminals are
constructed of PCOCC copper. This meticulous care and attention
given to every minute detail in both the vibration and generator
systems has resulted in a significant improvement in the performance
and sound quality. This superb cartridge offers audiophiles and other
serious listeners added musical enjoyment.
Preliminary Installation
Keep stylus guard down. Remove
the stylus assembly by pulling away
from the cartridge body at a slight
rearward angle (Figure 3). Place the
stylus assembly out of harm's way.
Mount the cartridge body to the
tone arm head shell.* Use the
mounting hardware supplied with the cartridge or with the turntable,
and tighten until just snug. Replace the stylus assembly briefly to check
for mechanical interference with mounting hardware. The stylus
assembly should click into place. Again remove the stylus assembly for
safekeeping.
Electrical Connections
Four terminals at the rear of the cartridge are color-coded to match
standard wiring in stereo tone ar Connect with slip-onms (Figure 4).
lugs provided on the head shell wiring. NEVER SOLDER TO
CARTRIDGE TERMINALS! Heat applied to the terminals will damage
the internal cartridge wiring.
For monaural operation, the Left
and Right signal terminals should be
connected to the monaural signal
lead, and the Left and Right ground
terminals should be connected to
the ground lead.
Final Adjustment
It is especially important that the
“overhang” and tone arm height should be exactly correct. The stylus
overhang, or distance from the stylus tip to the center of the turntable,
should be 15mm. You can check for correct overhang with the plastic
gauge to which y idge is mounted in the packaging.our cartr
Replace the stylus assembly; flip the stylus guard up. You should
be certain that the stylus assembly and cartridge body are exactly
perpendicular to the record surface, and that the cartridge is aligned
with the sides of the tone arm for best performance.
If possible, adjust the arm height so that the top of the cartridge is
parallel to the record surface when the stylus is cued down on the
record.
Connection to System
Run two shielded audio cables from the cartridge/tone arm connec-
tions on the turntable to the magnetic phono inputs on the amplifier or
receiver. Observe Left and Right channel markings.
To assure maximum performance, the lowest possible connecting
cable losses between turntable and amplifier are required. Very short
conventional cables may be used.
A separate ground wire usually comes attached to the turntable of
most electronics.
Distorted or unbalanced sound from the two phono channels often
can be traced to wires interchanged or touching at the cartridge
terminals. A reduction in output or muffled sound may result if the
stylus assembly is not fully seated. Hum from the phonograph input
can usually be traced to a bad audio cable or absence of the separate
ground wire from turntable to amplifier.
*Note: These instructions assume that you will be using this cartridge
in conjunction with a tone arm having a universal head shell. If your
tone arm has a different style head shell, follow the instructions
included with your tone arm.
AT150MLX
Vector-Aligned™
Stereo Phono Cartridge
Wide Range Vector-Aligned Vibration
System and Improved Paratoroidal Signal Generating
System featuring PCOCC Wire
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Isolated PCOCC
Paratoroidal Coils
Mu-Metal Shield
Laminated Coil Core with
Unitized Pole Pieces
Vector-Aligned Dual Magnets
Nude-Mounted Microline Natural Diamond Stylus
0.3mm Diameter Gold-plated Boron Cantilever
Radial Damping Ring at Cantilever Fulcrum
Individual Compliance Adjustment Screw
Left Output (White)
Right Output
(Red)
Right Ground
(Green)
Left Ground
(Blue/Black)
Stylus
Guard
CartridgeStylus Assembly
Produkt Specifikationer
| Mærke: | Audio-Technica |
| Kategori: | DJ udstyr |
| Model: | AT150MLX |
Har du brug for hjælp?
Hvis du har brug for hjælp til Audio-Technica AT150MLX stil et spørgsmål nedenfor, og andre brugere vil svare dig
DJ udstyr Audio-Technica Manualer
4 April 2024
27 Februar 2024
13 December 2023
15 August 2023
9 August 2023
30 Juni 2023
4 April 2023
3 December 2022
6 November 2022
DJ udstyr Manualer
- DJ udstyr Denver
- DJ udstyr Sencor
- DJ udstyr Pro-Ject
- DJ udstyr Lenco
- DJ udstyr Pioneer
- DJ udstyr Faderfox
- DJ udstyr Qtx
- DJ udstyr Behringer
- DJ udstyr Kenwood
- DJ udstyr Roland
- DJ udstyr Pyle
- DJ udstyr Denon
- DJ udstyr Auna
- DJ udstyr Muse
- DJ udstyr Thomson
- DJ udstyr Pyle Pro
- DJ udstyr AKAI
- DJ udstyr Skytec
- DJ udstyr König
- DJ udstyr TechniSat
- DJ udstyr Crosley
- DJ udstyr Kärcher
- DJ udstyr Festo
- DJ udstyr Wacom
- DJ udstyr Technics
- DJ udstyr HQ
- DJ udstyr Krüger&Matz
- DJ udstyr PreSonus
- DJ udstyr Victrola
- DJ udstyr NAD
- DJ udstyr ESI
- DJ udstyr Tascam
- DJ udstyr Omnitronic
- DJ udstyr Swann
- DJ udstyr Zoom
- DJ udstyr Dual
- DJ udstyr Korg
- DJ udstyr Arturia
- DJ udstyr RME
- DJ udstyr Onkyo
- DJ udstyr Line 6
- DJ udstyr Teac
- DJ udstyr Thorens
- DJ udstyr Marantz
- DJ udstyr Soundcraft
- DJ udstyr American Audio
- DJ udstyr Monacor
- DJ udstyr ION
- DJ udstyr Numark
- DJ udstyr Allen & Heath
- DJ udstyr Alesis
- DJ udstyr Native Instruments
- DJ udstyr Gemini
- DJ udstyr Suonobuono
- DJ udstyr Universal Audio
- DJ udstyr Hercules
- DJ udstyr Reloop
- DJ udstyr DAP-Audio
- DJ udstyr Ortofon
- DJ udstyr DB Technologies
- DJ udstyr Atomix
- DJ udstyr MoFi
- DJ udstyr Ecler
- DJ udstyr Denon DJ
- DJ udstyr NUX
- DJ udstyr DTronics
- DJ udstyr Headliner
Nyeste DJ udstyr Manualer
19 December 2024
19 December 2024
19 December 2024
18 December 2024
9 December 2024
7 December 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024