Barska BA11497 Manual


Læs nedenfor 📖 manual på dansk for Barska BA11497 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
©2010 BARSKA®| La Verne, CA 91750 | USA | www.barska.com BC1626/10
1. Unscrew tail cap of flashlight.
2. Insert two CR123 batteries as illustrated, positive end first into flashlight.(not included)
3. Screw tail cap of flashlight back on to flashlight.
· 3 levels of brightness
· Rapid strobe mode
· S.O.S. light pattern
· Operates on two
CR123 batteries
(not included)
- 1” Weaver mounting ring
- Momentary on/off long
cable switch
- Wrist strap
INSTALLING BATTERIES
OPERATION
CR 12 3 CR 12 3
1. To turn flashlight on, press and hold button firmly. You will hear a click. Flashlight is on and is
at the Highest setting.
2. To switch through the various lighting modes gently press the button. Lighting modes
are as follows;
- Tap once Medium Lighting Mode
- Click flashlight on, flashlight is on at the Highest Lighting Mode
- Tap once more Low Lighting Mode
- Tap once more Rapid Strobe Mode
- Tap once more S.O.S. Light Pattern Mode ( 3 short bursts, 3 long flashes, 3 short bursts)
- Click button once to turn it off
3. To turn flashlight off at any of the lighting modes press and hold button firmly. You will hear a
click. Flashlight is now off.
USING THE MOMENTARY CABLE SWITCH
1. To add the momentary on/off long cable switch onto flashlight, unscrew the tail cap of flashlight
and set aside.
2. While keeping the batteries in the flashlight, screw the momentary on/off long cable switch on
to the flashlight.
3. To switch through the various lighting modes hold down the button of the cable switch. Lighting
modes are as follows;
- Hold down cable button flashlight is at the Highest Lighting Mode
- Hold down cable button again for Medium Lighting Mode
- Hold down cable button again for Low Lighting Mode
- Hold down cable button again for Rapid Strobe Mode
- Hold down cable button again for S.O.S. Light Pattern Mode
- Hold down cable button again for High Lighting Mode
4. To turn flashlight off at any of the lighting modes, release the cable switch button.
5. To remove the momentary on/off long cable switch, unscrew the long cable switch from
flashlight and set aside. While keeping batteries in the flashlight, screw the tail cap on to the
flashlight.
MOUNTING FLASHLIGHT
1. With an Allen wrench loosen the top screws of the ring and carefully separate
the top piece of ring from the bottom half.
2. Position the tube of the flashlight in the groove of the bottom half of the ring.
3. Place the top piece of ring with screws over the top of the flashlight and
bottom half of flashlight.
4. With an Allen wrench tighten screws to join the top and bottom halves of the ring together.
Your flashlight is ready to be mounted to a firearm.
5. Loosen the lock nut located on the side of the ring, mount ring with flashlight using the
grooves of the ring to the rail of the firearm and tighten the lock nut in place.
6. To dismantle mounted flashlight, loosen lock nut and remove mounted flashlight from the rail
of firearm. Using an Allen wrench unscrew the screws from the top of the ring and remove
flashlight from ring. Place top half of ring on top of the bottom half of the ring and screw pieces
back together.
Features Includes
WARNING: USE OF FLASHLIGHT FOR AN EXTENSIVE PERIOD OF TIME WILL
CAUSE OVERHEATING. IF OVERHEATING OCCURS, TURN FLASHLIGHT OFF
AND ALLOW IT TO COOL BEFORE RE-USING.


Produkt Specifikationer

Mærke: Barska
Kategori: Ikke kategoriseret
Model: BA11497

Har du brug for hjælp?

Hvis du har brug for hjælp til Barska BA11497 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Barska Manualer

Barska

Barska BA11497 Manual

25 August 2024
Barska

Barska BA12196 Manual

25 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024