Binatone Latitude 100 Manual

Binatone Radio Latitude 100

Læs nedenfor 📖 manual på dansk for Binatone Latitude 100 (2 sider) i kategorien Radio. Denne guide var nyttig for 49 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

3. Operation

3.1 Turning the Unit ON/OFF

3.2 Adjusting the Speaker volume

There are 8 volume levels. To adjust the speaker volume,

press the (UP) button to increase, or press the

(DOWN) button to decrease. The LCD Screen will show

the digital speaker volume level during adjustment.

3.3 Receiving a Call

The unit is continuously in Receive mode when the

unit is turned ON and not transmitting. When a signal is

received on the current channel, the receive signal icon

“RX” will be displayed on the LCD Screen.

3.4 Transmitting (sending)

Press and hold the (Push to Talk) button to transmit

your voice. The transmit signal icon “TX” will display on

the LCD Screen and the RED LED indicator will light.

Hold the unit in a vertical position with the Mic

(Microphone) 5 cm away from the mouth. While holding

the button, speak into the mic (microphone) in a

normal tone of voice.

Release the button when you have finished

transmitting.

Important:

In order for other people to receive your transmission, they must

also be on the same channel that you are currently using. Refer

to the "Changing Channel" section for more information.

When the and/or CALL buttons are continuously pressed,

your PMR cannot receive any transmissions.

To Turn ON;

a. Press and hold the (Power) button. A special “beep"

sound will be heard and the LCD Screen will display the

current channel.

To switch OFF;

b. Press and hold the (Power) button. A special “beep"

sound will be heard and the LCD Screen will turn blank.

3.5 Calling (Paging) Tone

With the PMR in normal mode, press and release the CALL

button. The unit will transmit a 2-second page tone to the

other unit/s set with the same channel within transmitting

range.

You can use the CALL button to send a tone to other users on

the same channel. To activate this feature;

Binatone Help Line - 0845 345 9677

2. Installation

2.1 Removing the Belt Clip

a. Pull the Belt Clip Latch

away from the PMR.

b. While pulling the Belt

Clip Latch, push up

the Belt Clip as

shown in Figure 1.

Figure 1

Figure 2

Belt clip

latch

2.2 Installing the Belt

Clip

a. Slide the Belt Clip into

the slot as shown in

Figure 2.

A “click” indicates the b.

Belt Clip is locked into

position.

Notes:

Use only same type and make of batteries on the PMR units.

The PMR units have a built-in Power Saver (PS) for maximum

battery life, but when not in use, turn the unit OFF to

conserve battery power.

Remove the batteries if the units will not be used for a long

period of time.

2.3 Installing the Batteries

Caution: Observe the proper battery polarity orientation when

installing batteries. Incorrect positioning can damage both the

batteries and the unit.

a. Release the Battery Compartment Cover Latch located on the rear

side of the PMR then remove the Battery Compartment Cover from

the Battery Compartment. See Figure 3.

Install 3 x 1.5V AAA/LR03 regular Alkaline or Ni-MH b.

rechargeable batteries by following the orientation as

shown in Figure 3.

Replace the Battery Compartment Cover. c.

Lock the Battery Compartment Cover Latch into position.d.

Figure 3

Figure 4

3.7 The Menu Functions

3.7.1 Changing Channels

The PMR has 8 available channels. To change channel;

a. Press the (Menu) button once, the Channel icon

“ ” will start blinking on the LCD Screen.8

b. While the Channel icon is blinking, press the (UP) or

(DOWN) button to select the desired channel. The

channel changes from 1 to 8, or from 8 to 1.

c. Press the button again to confirm your

selected channel.

3.7.3 Monitor

You can use the Monitor feature to check for weak signals

on the current channel.

a. Press the (Menu) button 3 times. The PMR will

enter the Monitor mode and hear everything on the

current channel.

b. Press the (Menu) button again to turn off the

Monitor operation and return to standby mode.

3.7.2 TX Power High/Low setting

This feature permits the selection of the transmitting power

level to high or low. At Power High, the PMR will transmit

at maximum power and at a longer transmission range.

a. Press the (Menu) button twice.

b. Press the (UP) or (DOWN) button to select

High or Low. The LCD Screen will display "L" when the

low power is selected. At low power mode, the PMR

will transmit at reduced transmitting range but could

extend the battery life.

c. Press the button again to confirm your

selected power level.

Note:

Refer to the "Channel Table" section of this Owner’s Manual for

detailed frequency listing.

CALL button

- Press to send a

ringing tone to other

PMR units.

TALK) button

- Press and hold

to transmit.

USER GUIDE

Private mobile radio

1. LCD Screen

Channel Number. Changes

from 1 to 8 as selected by the

user.

Displays the Speaker volume

level.

Antenna

LCD Screen

-Displays the

current channel

selection and other

radio symbols.

MENU/ (Power)

Button

-(Menu) Press to program

the PMR settings.

(Power) Press and

hold to turn the

PMR unit ON

or OFF.

(UP)/ (DOWN)

buttons - Press to

change channels,

volume, and to

select settings

during programming.

Mic (Microphone)

Speaker

Displayed when the Power Low is activated.

Displayed when transmitting a signal.

Displayed when receiving a signal.

SCAN button

Press and hold to

scan for an active

channel.

RED LED Indicator

lighting

TALK (PUSH to

3.6 Channel Scan

Press and hold down the button. The channel

number on the LCD creen changes rapidly until an active

signal is detected.

When an active signal (one of the 8 channels) is detected,

(OR press the (UP) button to continue the

Channel scan performs a search for active signals in a

other radios without having to manually change to each channel.

SCAN

continuous loop from channels 1 to 8. This allows you to find

the channel scan pauses on the active channel until the

active signal stops.

If you press the button while the scan is paused on

an active channel the unit will communicate through the

and the channel scan will be active signal channel,

channel scanning.)

deactivated.

Press and hold the SCAN button to stop the channel

scanning operation. The unit will return to the channel

If no action is taken before the detected signal stops then

the scan will continue.

set before the scan was started.

To activate this feature;

TALK

Produkt Specifikationer

Mærke:	Binatone
Kategori:	Radio
Model:	Latitude 100
Batteriteknologi:	Nikkel-Metalhydrid (NiMH)
Indikator for batteriniveau:	Ja
Driftsfrekvens:	446.00625 - 446.09375 Mhz
Maks. rækkevidde:	3000 m
Genopladelig:	Ja
Bælteclip:	Ja
Antal kanaler (i alt):	8 kanaler