Black And Decker FS500 Manual
Black And Decker
Rysteplaster
FS500
Læs nedenfor 📖 manual på dansk for Black And Decker FS500 (4 sider) i kategorien Rysteplaster. Denne guide var nyttig for 25 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/4
GENERAL SAFETY RULES
WARNING: Read and understand all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
•Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.
•Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
•Double insulated tools are equipped with a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug in any way. Double insulation
eliminates the need for the three wire grounded power cord and grounded power supply
system.
•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
•Don’t expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
•When operating a power tool outside, use an outdoor extension cord marked "W-A"
or "W". These cords are rated for outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
•Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury.
•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair
can be caught in moving parts. Air vents may cover moving parts and should be avoided.
•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that have the switch on invites accidents.
•Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is
left attached to a rotating part of the tool may result in personal injury.
•Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.
•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
•Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss
of control.
•Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
•Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the tool. Such preventative safety measures reduce
the risk of starting the tool accidentally.
•Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools, with sharp cutting edges are less likely to bind and are easier to control.
•Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tools operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
•Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used on
another tool.
SERVICE
•Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement parts. Follow instructions in
the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
CAUTION: Wear appropriate hearing protection during use. Under some conditions
and duration of use, noise from this product may contribute to hearing loss.
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min........................minutes ......................alternating current
......................direct current no........................no load speed
..........................Class II Construction ........................earthing terminal
........................safety alert symbol .../min ..................revolutions or
reciprocations
per minute
CAT. NO. FS500, FS1000 FORM NO. 612289-00 PRINTED IN CHINA (MAY-02-1)
KEY INFORMATION YOU SHOULD KNOW:
• Never operate the sander without recommended
sandpaper properly installed on the base.
• Do not push down—let the sander do the work.
• Extended drywall sanding is not recommended for
these products.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
INSTRUCTION MANUAL
Catalog Nos. FS500, FS1000
P
P
P
P
P
P
P
P
P
Pa
a
a
a
a
a
a
a
a
al
l
l
l
l
l
l
l
l
lm
m
m
m
m
m
m
m
m
m
G
G
G
G
G
G
G
G
G
Gr
r
r
r
r
r
r
r
r
ri
i
i
i
i
i
i
i
i
ip
p
p
p
p
p
p
p
p
p
S
S
S
S
S
S
S
S
S
Sa
a
a
a
a
a
a
a
a
an
n
n
n
n
n
n
n
n
nd
d
d
d
d
d
d
d
d
de
e
e
e
e
e
e
e
e
er
r
r
r
r
r
r
r
r
r
SAFETY WARNINGS AND INSTRUCTIONS: DOUBLE INSULATION
Double insulated tools are constructed throughout with two separate layers of electrical
insulation or a double thickness of insulation between you and the tool’s electrical system.
Tools built with double insulation are not intended to be grounded. As a result, your tool is
equipped with a two prong plug which permits you to use extension cords without concern for
maintaining a ground connection.
Double insulation does not take the place of normal safety precautions when operating this
tool. The insulation system is for added protection against injury resulting from a possible
electrical insulation failure within the tool.
REPLACEMENT PARTS: When servicing use only identical replacement parts. Repair or
replace damaged cords.
SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk
of electric shock. When provided, this plug will fit into a polarized outlet only one way. If the
plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
SAFETY WARNINGS AND INSTRUCTIONS: SANDERS
•ALWAYS WEAR EYE PROTECTION.
• Clean your tool out periodically.
OTHER IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS
EXTENSION CORDS
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.
SANDING LEAD BASED PAINT
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is to children and pregnant
women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis,
we recommend the following precautions when sanding any paint:
PERSONAL SAFETY
• No children or pregnant women should enter the work area where the paint sanding is being
done until all clean up is completed.
• A dust mask or respirator should be worn by all persons entering the work area. The filter
should be replaced daily or whenever the wearer has difficulty breathing.
NOTE: Only those dust masks suitable for working with lead paint dust and fumes should
be used. Ordinary painting masks do not offer this protection. See your local hardware
12
ON OFF SWITCH
INTERRUPTEUR
INTERRUPTOR DE ENCENDIDO Y APAGADO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO1-800-54-HOW-TO
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALLFOR ANY REASON PLEASE CALL
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR PURCHASE,BLACK & DECKER
CALL .1-800-54-HOW-TO (1-800-544-6986)
IN MOST CASES, A REPRESENTATIVEBLACK & DECKER
CAN RESOLVE YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT,
GIVE US A CALL. YOUR FEEDBACK IS VITAL
TO THE SUCCESS OF BLACK & DECKER S QUALITY ’
IMPROVEMENT PROGRAM.
(544-6986)
34
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
FS500
FS1000
Produkt Specifikationer
| Mærke: | Black And Decker |
| Kategori: | Rysteplaster |
| Model: | FS500 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Black And Decker FS500 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Rysteplaster Black And Decker Manualer
23 Maj 2024
14 Maj 2024
7 Maj 2024
19 April 2024
14 April 2024
5 April 2024
4 April 2024
18 Marts 2024
5 Marts 2024
3 Marts 2024
Rysteplaster Manualer
- Rysteplaster Scheppach
- Rysteplaster Bosch
- Rysteplaster Ozito
- Rysteplaster Metabo
- Rysteplaster DeWalt
- Rysteplaster RYOBI
- Rysteplaster Silverline
- Rysteplaster Skil
- Rysteplaster AEG
- Rysteplaster Makita
- Rysteplaster Worx
- Rysteplaster Güde
- Rysteplaster Biltema
- Rysteplaster Vonroc
- Rysteplaster Milwaukee
- Rysteplaster Parkside
- Rysteplaster Power Craft
- Rysteplaster Trotec
- Rysteplaster Einhell
- Rysteplaster Proxxon
- Rysteplaster Stanley
- Rysteplaster Hikoki
- Rysteplaster Hilti
- Rysteplaster Hitachi
- Rysteplaster Festool
- Rysteplaster Dremel
- Rysteplaster Fein
- Rysteplaster Craftsman
- Rysteplaster Powerplus
- Rysteplaster Fieldmann
- Rysteplaster Porter-Cable
- Rysteplaster Ridgid
- Rysteplaster Cotech
- Rysteplaster Handwerk
- Rysteplaster RIKON
- Rysteplaster Holzmann
- Rysteplaster Cocraft
- Rysteplaster Maestro
- Rysteplaster Mac Tools
- Rysteplaster Workzone
- Rysteplaster Tryton
- Rysteplaster Stalco
- Rysteplaster Prowork
Nyeste Rysteplaster Manualer
4 December 2024
23 November 2024
22 November 2024
15 November 2024
24 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
11 September 2024