Black And Decker JS250 Manual
Black And Decker
Sav
JS250
Læs nedenfor 📖 manual på dansk for Black And Decker JS250 (5 sider) i kategorien Sav. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/5
WARNING: Important Safety Warnings and Instructions
TO REDUCE RISK OF INJURY:
• Before any use, be sure everyone using this tool reads and understands all safety instructions
and other information contained in this manual.
• Save these instructions and review frequently prior to use and in instructing others.
WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk
of fire, electric shock, and personal injury, including the following.
READ ALL INSTRUCTIONS
General Safety Warnings and Instructions for All Tools
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t use power tools in
damp or wet locations. Keep work area well lit. Do not use tool in presence of flammable liquids or gases.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes,
radiators, ranges, and refrigerator enclosures.
• KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should be kept away
from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up place — out of
reach of children.
• DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was intended.
• USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool
for purpose not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber
gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering
to contain long hair.
• USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
• DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands
to operate tool.
• DON’T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have
repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep
handles dry, clean, and free from oil and grease.
• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when changing accessories,
such as blades, bits, cutters.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is off when
plugging in.
• EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. The following table shows the
correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gage. The smaller the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating More Not more AWG
Than Than 0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for
use outdoors and so marked.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced
by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off.
Safety Warnings and Instructions: Double Insulation
Double insulated tools are constructed throughout with two separate layers of electrical insulation or one
double thickness of insulation between you and the tool’s electrical system. Tools built with this insulation
system are not intended to be grounded. As a result, your tool is equipped with a two prong plug which
permits you to use extension cords without concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or replace damaged
cords.
Safety Warnings and Instructions: Polarized Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk of electric shock.
When provided, this plug will fit in the polarized outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not
change the plug in any way
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
The label on your tool may include the following symbols.
V ..........................volts A ........................amperes
Hz ........................hertz W ......................watts
min ......................minutes ......................alternating current
....................direct current n o ......................no load speed
........................
Class II Construction ........................earthing terminal
........................safety alert symbol .../min ................revolutions or
reciprocations
per minute
Safety Warnings and Instructions: Jig Saws
CAUTION: When cutting into walls, floors or wherever live electrical wires may be encountered, DO NOT
TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by insulated grasping surfaces to prevent
electric shock if you cut in the live wire.
INSTRUCTION MANUAL
KEY INFORMATION YOU SHOULD KNOW:
• The saw cannot be turned on by only rotating the speed wheel the trigger must be
depressed.
•Securely tighten roller support guide before use.
• Pull up scroller knob completely before rotating.
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO1-800-54-HOW-TO
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALLFOR ANY REASON PLEASE CALL
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR PURCHASE,BLACK & DECKER
CALL .1-800-54-HOW-TO (1-800-544-6986)
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE
CAN RESOLVE YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT,
GIVE US A CALL. YOUR FEEDBACK IS VITAL
TO THE SUCCESS OF BLACK & DECKER'S QUALITY
IMPROVEMENT PROGRAM.
(544-6986)
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
Cat. No. .JS350 Form No. 386873-01 Copyright © 2000 Black & Decker Printed in England
BLADE
LAME
SEGUETA
OUICK CLAMP™ BLADE CLAMP LEVER
LEVIER DU SERRE-LAME QUICK CLAMPmc
PALANCA DEL PORTA SEGUETAS QUICK CLAMP™
BLADE
LAME
SEGUETA
12
3
SPEED WHEEL
RÉGULATEUR DE VITESSE
PERILLA DE CONTROL DE VELOCIDAD
TRIGGER SWITCH
INTERRUPTEUR À DÉTENTE
GATILLO INTERRUPTOR
LOCK ON BUTTON
BOUTON DE VERROUILLAGE
EN MODE DE FONCTIONNEMENT
BOTON DE ENCENDIDO PERMANENTE
4
5
SHOE
PATIN
ZAPATA
REAR SCREW
VIS ARRIÈRE
TORNILLO TRASERO
ROLLER SUPPORT GUIDE SCREW
VIS DU ROULEAU PORTEUR
TORNILLO DE LA GUIA DE SOPORTE DE RODILLO
0
15
6
ANGLE ADJUSTMENT MARKINGS
MARQUES DE RÉGLAGE DE L’ANGLE
MARCAS DE AJUSTE ANGULAR
SCROLLER RELEASE BUTTON
BOUTON DE DÉGAGEMENT DU
MODE DE CHANTOURNAGE
BOTON DE LIBERACION DE CALADO
DUST BLOWER SWITCH
INTERRUPTEUR DU VENTILATEUR
INTERRUPTOR DEL SOPLADOR
DUST EXTRACTION
DÉPOUSSIÉRAGE
EXTRACCION DE POLVO
CUT LINE BLOWING
VENTILATION DE LA LIGNE DE COUPE
SOPLADO EN LA LINEA DE CORTE
78
910
SCREW
VIS
TORNILLO
V
V
V
V
VV
V
V
V
V
VV A
A
A
A
AA
A
A
A
A
AAR
R
R
R
RR
R
R
R
R
RRI
I
I
I
II
I
I
I
I
IIA
A
A
A
AA
A
A
A
A
AAB
B
B
B
BB
B
B
B
B
BB L
L
L
L
LL
L
L
L
L
LL E
E
E
E
EE
E
E
E
E
EE S
S
S
S
SS
S
S
S
S
SSP
P
P
P
PP
P
P
P
P
PP E
E
E
E
EE
E
E
E
E
EE E
E
E
E
EE
E
E
E
E
EE D
D
D
D
DD
D
D
D
D
DD S
S
S
S
SS
S
S
S
S
SS C
C
C
C
CC
C
C
C
C
CCR
R
R
R
RR
R
R
R
R
RRO
O
O
O
OO
O
O
O
O
OO L
L
L
L
LL
L
L
L
L
LL L
L
L
L
LL
L
L
L
L
LL E
E
E
E
EE
E
E
E
E
EE R
R
R
R
RR
R
R
R
R
RR J
J
J
J
JJ
J
J
J
J
JJI
I
I
I
II
I
I
I
I
II G
G
G
G
GG
G
G
G
G
GG S
S
S
S
SS
S
S
S
S
SS A
A
A
A
AA
A
A
A
A
AAW
W
W
W
WW
W
W
W
W
WW
Catalog No. JS350
Produkt Specifikationer
| Mærke: | Black And Decker |
| Kategori: | Sav |
| Model: | JS250 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Black And Decker JS250 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Sav Black And Decker Manualer
28 Juni 2024
28 Juni 2024
22 Maj 2024
20 Maj 2024
6 Maj 2024
1 Maj 2024
23 April 2024
22 Februar 2024
22 Februar 2024
9 Februar 2024
Sav Manualer
- Sav Scheppach
- Sav Bosch
- Sav Ozito
- Sav Guede
- Sav Stiga
- Sav Panasonic
- Sav Metabo
- Sav Martha Stewart
- Sav DeWalt
- Sav Husqvarna
- Sav RYOBI
- Sav Silverline
- Sav Skil
- Sav Mafell
- Sav AEG
- Sav Gardena
- Sav AL-KO
- Sav Zipper
- Sav Stihl
- Sav McCulloch
- Sav Makita
- Sav Worx
- Sav Dolmar
- Sav Garden
- Sav Güde
- Sav Biltema
- Sav Jonsered
- Sav Vonroc
- Sav Hyundai
- Sav Milwaukee
- Sav Parkside
- Sav FERM
- Sav Trotec
- Sav Einhell
- Sav Proxxon
- Sav Stanley
- Sav Hikoki
- Sav Hilti
- Sav Hitachi
- Sav Kress
- Sav Remington
- Sav Park & Garden
- Sav Elu
- Sav Festool
- Sav Echo
- Sav EGO
- Sav Partner
- Sav Powerworks
- Sav Texas
- Sav Dremel
- Sav Kinzo
- Sav Powerfix
- Sav Elektra Beckum
- Sav Ford
- Sav Craftsman
- Sav Powerplus
- Sav Gamma
- Sav Westfalia
- Sav Genesis
- Sav Pattfield
- Sav Fieldmann
- Sav Cobra
- Sav Spear & Jackson
- Sav Porter-Cable
- Sav Baumr-AG
- Sav BabyGO
- Sav Ridgid
- Sav Sun Joe
- Sav Cotech
- Sav Snow Joe
- Sav Hobart
- Sav Royal Catering
- Sav Yard Force
- Sav Evolution
- Sav Ferrex
- Sav Fuxtec
- Sav RIKON
- Sav Extralink
- Sav Cocraft
- Sav Maestro
- Sav Yellow Garden Line
- Sav Wolfcraft
- Sav Mac Tools
- Sav Workzone
- Sav Tryton
- Sav Varo
- Sav Batavia
- Sav Protool
- Sav Stalco
- Sav Triton
- Sav Lux Tools
- Sav Anova
- Sav Fleurelle
- Sav Dual Saw
- Sav Toolson
- Sav Dexter Power
- Sav Toledo
- Sav Graule
- Sav Exakt
- Sav Mac Allister
- Sav MSW
- Sav Prowork
Nyeste Sav Manualer
17 November 2024
17 November 2024
16 November 2024
15 November 2024
15 November 2024
14 November 2024
3 November 2024
22 Oktober 2024
20 Oktober 2024
20 Oktober 2024