Black And Decker TV900 Manual
Black And Decker
Sav
TV900
Læs nedenfor 📖 manual på dansk for Black And Decker TV900 (4 sider) i kategorien Sav. Denne guide var nyttig for 31 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/4
TRIGGER SWITCH
INTERRUPTEUR À DÉTENTE
GATILLO INTERRUPTOR
WARNING: Read and understand all instructions. Failure to follow all instructions list-
ed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.
•Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
•Double insulated tools are equipped with a polarized plug (one blade is wider than the
other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install a polarized outlet. Do not change the plug in any way. Double insulation
eliminates the need for the three wire grounded power cord and grounded power supply
system.
•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
• WDon’t expose power tools to rain or wet conditions. ater entering a power tool will
increase the risk of electric shock.
•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged
cords immediately. Damaged cords increase the risk of electric shock.
•When operating a power tool outside, use an outdoor extension cord marked “W-A”
or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When
using an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. The table below shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage
number, the heavier the cord.
PERSONAL SAFETY
•Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury,
•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair and clothing away from moving parts. Loose clothing, jewelry, or long hair can be
caught in moving parts.
•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that have the switch on invites accidents.
• ARemove adjusting keys or wrenches before turning the tool on. wrench or key that is
left attached to a rotating part of the tool may result in personal injury.
•Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.
•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
•Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to a loss
of control.
•Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
•Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. Such preventative safety measures reduce the risk of
starting the tool accidentally.
• TStore idle tools out of reach of children and other untrained persons. ools are
dangerous in the hands of untrained users.
•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edges are less likely to bind and are easier to control.
•Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tools operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
•Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used on
another tool.
SERVICE
•Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury. WARNING! Read and
understand all instructions. Failure to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
ADDITIONAL SAFETY RULES
•Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will
make exposed metal parts of the tool "live" and shock the operator.
• KEEP HANDS AWAY from cutting area. Never reach underneath the material for any rea-
son. Hold front of saw by grasping the contoured gripping area. Do not insert fingers or thumb
into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the saw by grip-
ping the shoe.
• KEEP BLADES SHARP. Dull blades may cause the saw to swerve or stall under pressure.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other repro-
ductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
Fig. 1
Fig. 2
BLADE GUARD
PROTÈGE-LAME
GUARDA DE LA SEGUETA
BLADE CLAMP
SERRE-LAME
SUJETADOR DE LA SEGUETA
RECIPROCATING SHAFT
ARBRE À MOUVEMENT ALTERNATIF
EJE ALTERNATIVO
(BLADE GUARD CUT AWAY FOR
CLARITY)
(PROTÈGE-LAME DÉCOUPÉ AFIN
DE MIEUX VOIR)
(GUARDA DE LA SEGUETA CORTE
PARA MAYOR VISIBILIDAD)
SET SCREW
VIS DE FIXATION
PRISIONERO
BLADE
LAME
CUCHILLA PIN ON SHAFT
ERGOT SUR L'ARBRE
PERNO EN EL EJE
Fig. 4
Fig. 5
Fig. 3
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min ........................minutes ......................alternating current
......................direct current no ........................no load speed
..........................Class II Construction ........................earthing terminal
........................safety alert symbol SPM ....................strokes per minute
.../min ....................revolutions or
reciprocations
per minute
OPERATION
CAUTION: THE BLADE GUARD IS THERE FOR YOUR SAFETY. DO NOT REMOVE IT.
CAUTION: Always wear eye protection while operating this power tool.
NOTE:Before cutting any type of material, be sure it is firmly anchored or clamped to prevent
slipping.
• Place blade and blade guard lightly against work to be cut.
• Switch on saw motor and allow it to obtain maximum speed before applying pressure.
• Always hold saw firmly with both hands while cutting. Whenever possible, the saw guard
must be held firmly against the material being cut. This will prevent the saw from jumping or
vibrating and minimize blade breakage.
INFORMATION YOU SHOULD KNOW
• Securely tighten blade.
• Keep shoe firmly against work surface.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTESADVERTENCIA:
DE USAR EL PRODUCTO.
CAT. NO. TV900 FORM NO. 395636 Copyright © 2000 Black & Decker (JUN00-1) Printed in U.S.A.
Fig. 6
Catalog Number TV900
®
1-800-544-6986
V
V
V
VV
V
V
V
VVA
A
A
AA
A
A
A
AAR
R
R
RR
R
R
R
RRI
I
I
II
I
I
I
IIA
A
A
AA
A
A
A
AAB
B
B
BB
B
B
B
BBL
L
L
LL
L
L
L
LLE
E
E
EE
E
E
E
EES
S
S
SS
S
S
S
SSP
P
P
PP
P
P
P
PPE
E
E
EE
E
E
E
EEE
E
E
EE
E
E
E
EED
D
D
DD
D
D
D
DDR
R
R
RR
R
R
R
RRE
E
E
EE
E
E
E
EEC
C
C
CC
C
C
C
CCI
I
I
II
I
I
I
IIP
P
P
PP
P
P
P
PPR
R
R
RR
R
R
R
RRO
O
O
OO
O
O
O
OOC
C
C
CC
C
C
C
CCA
A
A
AA
A
A
A
AAT
T
T
TT
T
T
T
TTI
I
I
II
I
I
I
IIN
N
N
NN
N
N
N
NNG
G
G
GG
G
G
G
GGS
S
S
SS
S
S
S
SSA
A
A
AA
A
A
A
AAW
W
W
WW
W
W
W
WW
INSTRUCTION MANUAL
Produkt Specifikationer
| Mærke: | Black And Decker |
| Kategori: | Sav |
| Model: | TV900 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Black And Decker TV900 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Sav Black And Decker Manualer
28 Juni 2024
28 Juni 2024
22 Maj 2024
20 Maj 2024
6 Maj 2024
1 Maj 2024
23 April 2024
22 Februar 2024
22 Februar 2024
9 Februar 2024
Sav Manualer
- Sav Scheppach
- Sav Bosch
- Sav Ozito
- Sav Guede
- Sav Stiga
- Sav Panasonic
- Sav Metabo
- Sav Martha Stewart
- Sav DeWalt
- Sav Husqvarna
- Sav RYOBI
- Sav Silverline
- Sav Skil
- Sav Mafell
- Sav AEG
- Sav Gardena
- Sav AL-KO
- Sav Zipper
- Sav Stihl
- Sav McCulloch
- Sav Makita
- Sav Worx
- Sav Dolmar
- Sav Garden
- Sav Güde
- Sav Biltema
- Sav Jonsered
- Sav Vonroc
- Sav Hyundai
- Sav Milwaukee
- Sav Parkside
- Sav FERM
- Sav Trotec
- Sav Einhell
- Sav Proxxon
- Sav Stanley
- Sav Hikoki
- Sav Hilti
- Sav Hitachi
- Sav Kress
- Sav Remington
- Sav Park & Garden
- Sav Elu
- Sav Festool
- Sav Echo
- Sav EGO
- Sav Partner
- Sav Powerworks
- Sav Texas
- Sav Dremel
- Sav Kinzo
- Sav Powerfix
- Sav Elektra Beckum
- Sav Ford
- Sav Craftsman
- Sav Powerplus
- Sav Gamma
- Sav Westfalia
- Sav Genesis
- Sav Pattfield
- Sav Fieldmann
- Sav Cobra
- Sav Spear & Jackson
- Sav Porter-Cable
- Sav Baumr-AG
- Sav BabyGO
- Sav Ridgid
- Sav Sun Joe
- Sav Cotech
- Sav Snow Joe
- Sav Hobart
- Sav Royal Catering
- Sav Yard Force
- Sav Evolution
- Sav Ferrex
- Sav Fuxtec
- Sav RIKON
- Sav Extralink
- Sav Cocraft
- Sav Maestro
- Sav Yellow Garden Line
- Sav Wolfcraft
- Sav Mac Tools
- Sav Workzone
- Sav Tryton
- Sav Varo
- Sav Batavia
- Sav Protool
- Sav Stalco
- Sav Triton
- Sav Lux Tools
- Sav Anova
- Sav Fleurelle
- Sav Dual Saw
- Sav Toolson
- Sav Dexter Power
- Sav Toledo
- Sav Graule
- Sav Exakt
- Sav Mac Allister
- Sav MSW
- Sav Prowork
Nyeste Sav Manualer
17 November 2024
17 November 2024
16 November 2024
15 November 2024
15 November 2024
14 November 2024
3 November 2024
22 Oktober 2024
20 Oktober 2024
20 Oktober 2024