Blaupunkt SR-S1 Manual


Læs nedenfor 📖 manual på dansk for Blaupunkt SR-S1 (2 sider) i kategorien Alarmsystem. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Wireless Indoor Siren (SR S1)-
P
Pa
ar
rt
ts
s
D
De
es
sc
cr
ri
ip
pt
ti
io
on
n
1. Mounting Holes x 4
2. Tamper Switch
The tamper switch protects the from being opened.cover
3. Function Switch Block
Contains 7 to enable the learning mode and to set DIP Switches
the alarm period of siren.
P
Pa
ac
ck
ka
ag
ge
e
C
Co
on
nt
te
en
nt
t
1 x Indoor Siren
4 x large wall plugs and screws
4 V x 1.5 D alkaline batteries
D
Di
ip
p
S
Sw
wi
it
tc
ch
h
1. Open the front cover
2. Open the battery cover to insert batteries.compartment
3. ocate the L Function Switch Block. Use a sharp bject to o set
Dip SW3 & SW4 on the function switch block to your desired
alarm length.
4. ontrol anel Enter learning mode for your c p .
5. Slide the position Dip SW1 to ON . SR S1- will enter learning
mode. he code After 3 seconds, t Siren will send a learning
and emit a beep to confirm.
6. If the Control Panel receives the learning signal, please refer
to the Control Panel manual to complete the learning process.
When learning is complete, the Control Panel will send signal
to the The Siren to confirm. Siren will sound a short beep
again to indicate learning is successful.
If the Control Panel fails to receive a learning code, slide Dip
SW1 back to OFF, and then ON position again to enter
learning mode again.
7. does no I f the Siren t respond, please remove the Siren from
the control panel and repeat steps 4-6 again.
8. S lide Dip the SW1 to OFF position to leave learning mode. If
you do t slide Dip SW1 back to OFF position, the no Siren will
automatically leave the learning mode in one hour.
The Indoor Siren has 4 mounting holes on the back cover for wall
mounting.
Before Installation, refer to your Control Panel manual to
temporarily disable the Siren Tamper function to avoid
accidental alarm trigger.
1. Use the 4 mounting holes on the back to mark position on the
wall.
2. Drill holes into the wall using the mounting holes as template,
insert wall plugs if required,
3. Fix the base onto the wall with the screw and plugs provided.
4. Replace the front cover onto the base.
5. Enab le the Siren Tamper function on you Control Panel.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
SW1
Siren Learning
OFF
Normal operation
ON
Learn-in mode
SW2
Reserved
SW3
SW4
Siren Duration
OFF
OFF
3 min.
ON
OFF
5 min.
OFF
ON
10 min.
ON
ON
1 second (test)
SW5
Reserved
SW6
Memory Reset
OFF
Normal
ON
Clear Memory
SW7
Supervision
OFF
Supervision function disable
ON
Supervision function enable
For further detail please see
L
Le
e
a
ar
rn
ni
in
ng
g
aanndd
O
Op
pe
er
ra
at
ti
io
on
n.
.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Mounting Holes
x 4


Produkt Specifikationer

Mærke: Blaupunkt
Kategori: Alarmsystem
Model: SR-S1

Har du brug for hjælp?

Hvis du har brug for hjælp til Blaupunkt SR-S1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Alarmsystem Blaupunkt Manualer

Blaupunkt

Blaupunkt SR-S1 Manual

5 August 2024
Blaupunkt

Blaupunkt Q3000 Manual

6 August 2023
Blaupunkt

Blaupunkt E01 Manual

10 Marts 2023
Blaupunkt

Blaupunkt S02 Manual

27 November 2022
Blaupunkt

Blaupunkt B01 Manual

12 November 2022

Alarmsystem Manualer

Nyeste Alarmsystem Manualer