Bogen MCD1X2U Manual

Bogen Højttaler MCD1X2U

Læs nedenfor 📖 manual på dansk for Bogen MCD1X2U (1 sider) i kategorien Højttaler. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
MCD1X2UGRILLE
Speaker Module
& Ceiling Grille
Assembly
The MCD1X2UGRILLE is warranted to be free from defects in
material & workmanship for two (2) years from the date of sale to
the original purchaser. This warranty does not extend to any of
our products that have been subjected to abuse, misuse, improper
storage, neglect, accident, improper installation or have been
modified or repaired or altered in any manner whatsoever, or
where serial number or date code has been removed or defaced.
2-YEAR WARRANTY
www.bogen.com
Specifications subject to change without notice.
© 2014 Bogen Communications, Inc. 53-2070-11C
Ceiling Grille Installation
To assemble the MCDMOD Speaker onto the MCD1X2UGRILLE, position the MCDMOD Speaker over the
portion of the Grille with the perforated speaker holes. On the MCDMOD there are two Tabs and a Module Clip.
The MCD1X2UGRILLE has two horizontal Grille Slots located on one side of the grille edge. Install the
MCDMOD Speaker on a slight angle and slide the Module Tabs into the Grille Slots . These Tabs should
go through completely so the MCDMOD is right up against grille edge. Then lower the MCDMOD down onto
the grille surface, and while doing this the Module Clip should clamp down onto the grille edge , securing
the MCDMOD flat and flush on to the MCD1X2UGRILLE.
MCMOD/MCD1X2UGRILLE
Assembly Installation
1. For a 2’ x 2’ ceiling tile space opening, remove the
existing ceiling tile and cut the tile to 11-1/2” long.
2. Place the MCD1X2UGRILLE into ceiling opening,
making sure the corner with perforated speaker
holes is situated on corner of existing ceiling grid.
3. Place the supplied Tile Bridge onto the ceiling grid
and slide to the center, allowing MCD1X2UGRILLE
to rest upon the Tile Bridge lip.
4. Re-install the cut ceiling tile back onto the ceiling grid
and Tile Bridge lip.
5. For a 2’ x 4 ceiling tile space opening, remove the
existing tile and cut the tile to 35-1/2” long. Then
follow steps 2 thru 4 to position ceiling speaker.
TILE BRIDGE
SUPPORT RAIL
CROSSBAR
MCD1X2UGRILLE
PERFORATED
SPEAKER HOLES
MODULE CLIP
FASTENS DOWN
ONTO GRILLE EDGE
MODULE TABS
SLIDE INTO
GRILLE SLOTS
MODULE
TABS
MODULE
CLIP
MCDMOD
1 2
1
2
2 ft. x 2 ft.
CEILING
GRID
TILE BRIDGE
11-1/2”
SPEAKER HOLES
TO BE SITUATED
IN CORNER OF
CEILING GRID
PERFORATED
SPEAKER
HOLES
MCD1X2U
GRILLE
CEILING
TILE
(Cut to
2 ft. x 11-1/2 in.)
CEILING TILE
2 ft. x 4 ft.
CEILING
GRID
(Cut to 2 ft. x 35-1/2 in.)
TILE BRIDGE
SPEAKER HOLES
TO BE SITUATED
IN CORNER OF
CEILING GRID
PERFORATED
SPEAKER
HOLES
MCD1X2U
GRILLE
35-1/2”
2 x 2
2 x 4
GRILLE
SLOTS
MCDMOD


Produkt Specifikationer

Mærke: Bogen
Kategori: Højttaler
Model: MCD1X2U

Har du brug for hjælp?

Hvis du har brug for hjælp til Bogen MCD1X2U stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Bogen Manualer

Bogen

Bogen WMT1AS Manual

10 December 2024
Bogen

Bogen NEAR S5T Manual

23 September 2024
Bogen

Bogen MPS1 Manual

18 September 2024
Bogen

Bogen OCS1 Manual

18 September 2024
Bogen

Bogen AFI-8 Manual

14 September 2024
Bogen

Bogen NQ-SMS1810-SCG Manual

1 September 2024
Bogen

Bogen CSD1X2 Manual

29 August 2024
Bogen

Bogen CSD2X2 Manual

19 August 2024
Bogen

Bogen KFLDS30T Manual

18 August 2024
Bogen

Bogen SEC4T Manual

18 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer