Boss FS-6 Manual

Boss Skifte FS-6

Læs nedenfor 📖 manual på dansk for Boss FS-6 (2 sider) i kategorien Skifte. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Thank you, and congratulations on your choice of BOSS FS-6 Dual Foot Switch. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” “IMPORTANT NOTES.” and

These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by

your new unit, this manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

Features

5 This unit combines the functions of the FS-5L (latch type) and FS-5U (momentary type) foot switches. Both of the unit’s foot switches

may be set to function as either a latch or momentary type switch.

5 You can connect to gear equipped with TRS 1/4” phone jacks using a connection cable with stereo 1/4” phone plugs at both ends.

5 The FS-6 can be connected to another FS-6, a FS-5U/5L, or an AB-2.

Use the FS-6 with BOSS or Roland devices compatible

with the FS-5L or FS-5U.

* No assurances can be given with respect to the proper

functioning of this unit if it is connected with devices or jacks

other than those specied.

Panel Description

1 2

1414

1. Pedal Switch A

Use this as a switch for the device connected to Jack A or

Jack A & B. Refer to “Connections.”

2. Pedal Switch B

Use this as a switch for the device connected to Jack B or

Jack A & B. Refer to “Connections.”

3. Pedal Switch A Indicator

When pedal switch A is set to the latch type function,

this indicator alternately lights or goes out each time the

pedal switch is pressed. When pedal switch A is set to the

momentary type function, this indicator lights only while

the pedal switch is held down.

4. Pedal Switch B Indicator

When pedal switch B is set to the latch type function,

this indicator alternately lights or goes out each time the

pedal switch is pressed. When pedal switch B is set to the

momentary type function, this indicator lights only while

the pedal switch is held down.

5. Jack A

Connect the device being controlled with pedal switch

A here. Use a connection cable with 1/4” phone plugs at

both ends.

6. Jack B

Connect the device being controlled with pedal switch

B here. Use a connection cable with 1/4” phone plugs at

both ends.

7. Jack A & B

Connect devices equipped with TRS 1/4” phone jacks

here. Use a connection cable with stereo 1/4” phone

plugs at both ends.

* Jacks A, B, and A & B also function as power switches. The power

is switched on when a plug is inserted in any of these jacks, and

switched o when no plug is connected. Unplug any cable from

these jacks whenever you are not using the unit.

8. POLARITY Switch A

This switches the polarity of pedal switch A.

After referring to the owner’s manual for the device you

are connecting, switch this to the appropriate setting.

9. POLARITY Switch B

This switches the polarity of pedal switch B.

After referring to the owner’s manual for the device you

are connecting, switch this to the appropriate setting.

10. MODE Switch A

This sets the function for pedal switch A to LATCH or

MOMENTARY.

11. MODE Switch B

This sets the function for pedal switch B to LATCH or

MOMENTARY.

LATCH:

Alternately switches on or o each time the pedal switch

is pressed.

MOMENTARY:

Switches on (o ) while the pedal switch is held down,

and o (on) when the switch is released.

12. POWER Indicator

This lights when the power is on (when a plug is

connected to a jack).

* If this indicator goes dim or no longer lights while the power

is on, the battery is near exhaustion and should be replaced

immediately.

13. Battery Cover

Open this cover to replace the battery. For instructions on

replacing the battery, refer to “Changing the Battery.”

14. FS Joint Panel

The FS-6 can be connected to another FS-6, a FS-5U/5L,

or an AB-2.

Before Using

Connect the battery supplied to the snap cord with

correct polarity.

Connections

* To prevent malfunction and/or damage to speakers or other

devices, always turn down the volume, and turn o the power on

all devices before making any connections.

Connecting to Jack A & B

Connection Cable

(stereo 1/4” phone plugs at both ends)

* When connecting to Jack A & B, do not plug any device into Jack A

or Jack B. This may result in damage and/or malfunction.

Connecting to Jack A or B

Setting the POLARITY Switch

When matching the FS-6’s polarity setting with the polarity

setting for the FS-5U or FS-5L given in the owner’s manual for

the device being connected, set as described below.

* According to these settings, the setting switches to OPEN when

the switch is on and CLOSE when the switch is o.

FS-5L / FS-5U FS-6

Changing the Battery

When the POWER indicator goes dim or no longer lights

while the power is on, it means that the battery is nearly

dead and must be replaced.

* When turning the unit upside-down, handle with care to avoid

dropping it, or allowing it to fall or tip over.

1. Open the battery cover.

When changing the battery,

be careful not to touch the

circuit board inside the unit.

2. Remove the old battery from the battery housing, and

remove the snap cord connected to it.

3. Connect the snap cord to the new battery.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Place the battery inside the housing.

5. While holding the assembly carefully, so the battery

cover doesn’t get separated from the battery, close the

battery cover.

* Press the cover until you hear it click into place.

Troubleshooting

Power not turning on (POWER indicator not lighting)

p Is the cable fully plugged into the jack?

The power switches when a cable is plugged into one of the

jacks. Make sure the cable is plugged in rmly and securely.

p Is the battery dead?

" Replace the battery with a new one as described in

“Changing the Battery.”

p Are you using a connection cable with stereo 1/4”phone

plugs at both ends to connect to Jack A or Jack B?

" Use a connection cable with mono 1/4” phone plugs at

both ends.

Connected device not operating properly

Have you connected to the appropriate jack on the device?

Check the type of jack used on the device being connected.

p Is the POWER indicator dimmed or o?

" The battery may be dead. Replace the battery with a new

one as described in “Changing the Battery.”

p Is the setting of the POLARITY switch correct?

" Set the polarity in accordance with the specications for

the connected device.

p Is the MODE switch setting correct?

" Set the MODE in accordance with the specications for the

connected device.

Pedal switch indicator not lighting

p Is the switch o?

" Depress the pedal switch.

p Is the POLARITY switch set rmly in the correct position?

" Make sure the POLARITY switch is set securely in the

correct position.

Indicator dimmed/o

" The battery may be dead. Replace the battery with a new

one as described in “Changing the Battery.”

This unit is a dedicated foot control device. Do not use it for any purpose other than those described in the owner’s manual.

Used for instructions intended to alert the

user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse eects caused with

respect to the home and all its

furnishings, as well to domestic animals

or pets.

Used for instructions intended to alert the

user to the risk of death or severe injury

should the unit be used improperly.

The ●

symbol alerts the user to things that must be

carried out. The specic thing that must be done is

indicated by the design contained within the circle. In the

case of the symbol at left, it means that the power-cord

plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or

warnings. The specic meaning of the symbol is

determined by the design contained within the triangle. In

the case of the symbol at left, it is used for general

cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be

carried out (are forbidden). The specic thing that must

not be done is indicated by the design contained within

the circle. In the case of the symbol at left, it means that

the unit must never be disassembled.

WARNING

Before using this unit, make sure to read

the instructions below, and the Owner's

Manual.

Do not open (or modify in any way) the

unit.

Do not attempt to repair the unit, or

replace parts within it (except when this

manual provides specic instructions

directing you to do so). Refer all servicing

to your retailer, the nearest Roland Service

Center, or an authorized Roland distributor,

as listed on the "Information."

Never use or store the unit in places that are:

• Subject to temperature extremes (e.g.,

direct sunlight in an enclosed vehicle,

near a heating duct, on top of heat-

generating equipment); or are

• Damp (e.g., baths, washrooms, on wet oors); or are

• Humid; or are

• Exposed to rain; or are

• Dusty; or are

• Subject to high levels of vibration.

Make sure you always have the unit placed

so it is level and sure to remain stable.

Never place it on stands that could

wobble, or on inclined surfaces.

Do not allow any objects (e.g., ammable

material, coins, pins); or liquids of any kind

(water, soft drinks, etc.) to penetrate the

unit.

Immediately turn the power o, and request

servicing by your retailer, the nearest Roland

Service Center, or an authorized Roland

distributor, as listed on the "Information" when:

• If smoke or unusual odor occurs

• Objects have fallen into, or liquid has been spilled

onto the unit; or

• The unit has been exposed to rain (or otherwise

has become wet); or

• The unit does not appear to operate normally or

exhibits a marked change in performance.

In households with small children, an

adult should provide supervision until the

child is capable of following all the rules

essential for the safe operation of the unit.

WARNING

Protect the unit from strong impact.

(Do not drop it!)

Batteries must never be recharged,

heated, taken apart, or thrown into re or

water.

CAUTION

Try to prevent cords and cables from

becoming entangled. Also, all cords and

cables should be placed so they are out of

the reach of children.

Never climb on top of, nor place heavy

objects on the unit.

Disconnect all cords coming from external

devices before moving the unit.

If used improperly, batteries may explode

or leak and cause damage or injury. In the

interest of safety, please read and observe

the following precautions.

• Carefully follow the installation

instructions for batteries, and make sure

you observe the correct polarity.

• Remove the batteries whenever the unit is

to remain unused for an extended period of time.

• If a battery has leaked, use a soft piece of cloth or

paper towel to wipe all remnants of the discharge

from the battery compartment. Then install new

batteries. To avoid inammation of the skin, make

sure that none of the battery discharge gets onto

your hands or skin. Exercise the utmost caution

so that none of the discharge gets near your eyes.

Immediately rinse the aected area with running

water if any of the discharge has entered the eyes.

• Never keep batteries together with metallic objects

such as ballpoint pens, necklaces, hairpins, etc.

Used batteries must be disposed of in

compliance with whatever regulations for

their safe disposal that may be observed in

the region in which you live.

Roland Corporation

2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN

Roland Corporation

ENA 23 Zone 1 nr. 1620 Klaus-Michael Kuehnelaan 13, 2440 Geel, BELGIUM

Importer:

Manufacturer:

For EU Countries

Roland Corporation

2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN

Roland Europe Group Limited

Hive 2, 1530 Arlington Business Park, Theale, Reading, Berkshire. RG7 4SA United Kingdom

Importer:

Manufacturer:

For the U.K.

Specications

Controls

Pedal Switch A, B / POLARITY Switch A, B / Mode Switch A, B

Connectors

Jack A, Jack B (1/4 inch phone type)

Jack A & B (TRS 1/4 inch phone type)

Power Supply

DC 9 V: Dry battery/9 V 6F22 (carbon), 6LR61 (alkaline)

* Expected battery life under continuous use:

Carbon: 70 hours, Alkaline: 100 hours

(A and B = ON, MODE = LATCH)

These gures will vary depending on the actual conditions of use.

Current Draw

8 mA (max.)

Dimensions

188 (W) x 91 (D) x 43 (H) mm

7-7/16 (W) x 3-5/8 (D) x 1-3/4 (H) inches

Weight

470 g / 1 lb 1 oz (including battery)

Accessories

Dry battery/9 V (6F22), Owner’s Manual

* In the interest of product improvement, the specications and/or appearance of this

unit are subject to change without prior notice.

IMPORTANT NOTES

In addition to the items listed under “USING THE UNIT SAFELY”, please

read and observe the following:

Power Supply: Use of Batteries

5 Batteries should always be installed or replaced before connecting any other

devices. This way, you can prevent malfunction and/or damage to speakers or

other devices.

5 A battery was installed in the unit before it left the factory. The life of this battery

may be limited, however, since its primary purpose was to enable testing.

5 Before connecting this unit to other devices, turn o the power to all units. This

will help prevent malfunctions and/or damage to speakers or other devices.

Placement

5 Noise may be produced if wireless communications devices, such as cell phones,

are operated in the vicinity of this unit. Such noise could occur when receiving or

initiating a call, or while conversing. Should you experience such problems, you

should relocate such wireless devices so they are at a greater distance from this

unit, or switch them o.

5 Do not expose the unit to direct sunlight, place it near devices that radiate

heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature

extremes. Excessive heat can deform or discolor the unit.

5 When moved from one location to another where the temperature and/or

humidity is very dierent, water droplets (condensation) may form inside the

unit. Damage or malfunction may result if you attempt to use the unit in this

condition. Therefore, before using the unit, you must allow it to stand for several

hours, until the condensation has completely evaporated.

Maintenance

5 For everyday cleaning wipe the unit with a soft, dry cloth or one that has been

slightly dampened with water. To remove stubborn dirt, use a cloth impregnated

with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit

thoroughly with a soft, dry cloth.

5 Never use benzine, thinners, alcohol or solvents of any kind, to avoid the

possibility of discoloration and/or deformation.

Additional Precautions

5 Use a reasonable amount of care when using the unit’s buttons, sliders, or other

controls; and when using its jacks and connectors. Rough handling can lead to

malfunctions.

5 When connecting / disconnecting all cables, grasp the connector itself-never pull

on the cable. This way you will avoid causing shorts, or damage to the cable’s

internal elements.

5 To avoid disturbing your neighbors, try to keep the unit’s volume at reasonable

levels (especially when it is late at night).

5 When you need to transport the unit, package it in the box (including padding)

that it came in, if possible. Otherwise, you will need to use equivalent packaging

materials.

BOSS is a registered trademark of Roland Corporation in the United States

and/or other countries.

Owner’s Manual

Produkt Specifikationer

Mærke:	Boss
Kategori:	Skifte
Model:	FS-6

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss FS-6 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Boss Manualer

Boss ES-5 Manual

25 August 2024

Boss FS-6 Manual

6 August 2024

Skifte Manualer

Nyeste Skifte Manualer

Berker 80161865 Manual

16 December 2024

Berker 80262280 Manual

16 December 2024

Berker 80141170 Manual

16 December 2024

Berker 80162785 Manual

16 December 2024

Berker 80164773 Manual

16 December 2024

Berker 80162865 Manual

16 December 2024

Berker 80162780 Manual

16 December 2024

Berker 80142170 Manual

16 December 2024

Berker 80164776 Manual

16 December 2024

Berker 80262170 Manual

16 December 2024