Boss HM-2W Manual

Boss Ikke kategoriseret HM-2W

Læs nedenfor 📖 manual på dansk for Boss HM-2W (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

For the USA

SUPPLIER’S DECLARATION OF CONFORMITY

Compliance Information Statement

Model Name :

Type of Equipment :

Responsible Party :

Address :

Telephone :

HM-2W

GUITAR EFFECTS

Roland Corporation U.S.

5100 S. Eastern Avenue Los Angeles, CA 90040-2938

(323) 890-3700

HM-2W Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

English

Panel Descriptions

DC IN jack

AC adaptor

(PSA series; sold separately)

In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC

adaptor (PSA series; sold separately).

* Use only the specied AC adaptor (PSA series; sold

separately), and connect it to an AC outlet of the correct

voltage.

* If the AC adaptor is connected while a battery is installed,

the power supply is drawn from the AC adaptor.

Precautions When Connecting

• To prevent malfunction and equipment failure, always

turn down the volume, and turn o all the units

before making any connections.

• Once everything is properly connected, be sure to

follow the procedure below to turn on their power. If

you turn on equipment in the wrong order, you risk

causing malfunction or equipment failure.

When powering up: Turn on the power to your

guitar amp last.

When powering down: Turn o the power to your

guitar amp rst.

• Before turning the unit on/o, always be sure to turn

the volume down. Even with the volume turned

down, you might hear some sound when switching

the unit on/o. However, this is normal and does not

indicate a malfunction.

• Do not use connection cables that contain a built-in

resistor.

Use of Battery

• The life of the included battery may be limited as its

primary purpose was for testing during assembly.

• If you handle batteries improperly, you risk explosion

and uid leakage. Make sure that you carefully

observe all of the items related to batteries that are

listed in “USING THE UNIT SAFELY” and “IMPORTANT

NOTES” (supplied on a separate sheet).

• When operating on battery power only, the unit’s

indicator will become dim when battery power gets

too low. Replace the battery as soon as possible.

• If the batteries run extremely low, the sound may

distort, but this does not indicate a malfunction. If

this occurs, please replace the batteries or use the AC

adaptor (sold separately).

• Batteries should always be installed or replaced

before connecting any other devices. This way, you

can prevent malfunction and damage.

Changing the Battery

1. Hold down the pedal and loosen the

thumbscrew, then open the pedal upward.

Thumbscrew

Battery housing

Pedal

Spring base

Coil spring

Guide bush

hole

Battery snap

cord

Battery

snap

Battery

* The pedal can be opened without detaching the

thumbscrew completely.

2. Remove the old battery from the battery

housing, and remove the snap cord

connected to it.

3. Connect the snap cord to the new

battery, and place the battery inside the

battery housing.

* Be sure to carefully observe the battery’s polarity (+

versus -).

4. Slip the coil spring onto the spring base

on the back of the pedal, and then close

the pedal.

* Carefully avoid getting the snap cord caught in the

pedal, coil spring, and battery housing.

5. Finally, hold down the pedal while

tightening the thumbscrew into the

guide bush hole.

Main Specications

Nominal Input

Level -20 dBu

Input Impedance 1 MΩ

Nominal Output

Level -20 dBu

Output Impedance 1 kΩ

Recommended

Load Impedance 10 kΩ or greater

Power Supply

Alkaline battery (9 V, 6LR61 or 6LF22)

or Carbon-zinc battery (9 V, 6F22)

AC adaptor (PSA series: sold separately)

Current Draw

30 mA

Expected battery life under

continuous use (These gures

will vary depending on the actual

conditions of use.)

Alkaline: Approx. 24 hours

Carbon: Approx. 8 hours

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight

(including battery)

440 g

1 lbs

Accessories Leaet “USING THE UNIT SAFELY”

Alkaline battery (9 V, 6LR61 or 6LF22)

Option

(sold separately) AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the

product at the time that the document was issued.

For the latest information, refer to the Roland

website.

* Roland, BOSS, and WAZA CRAFT are either

registered trademarks or trademarks of Roland

Corporation in the United States and/or other

countries.

[COLOR MIX H] knob

Adjusts the tone around the 1 kHz frequency range. Turn the

knob clockwise to boost, and counterclockwise to cut.

[COLOR MIX L] knob

Adjusts the tone around the 100 Hz frequency range. Turn

the knob clockwise to boost, and counterclockwise to cut.

[LEVEL] knob

This knob adjusts the volume of the eect sound.

* No sound will be heard when this knob is rotated

completely counterclockwise.

OUTPUT jack

Use this 1/4” output jack to connect to

the input of your guitar amplier or the

input of additional eect unit. Guitar Amplier

Pedal switch

This switch turns the eects ON/OFF.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery

Check indicator.

The indicator lights when an eect is ON.

* The brightness of the CHECK indicator (LED) will dim as the battery lowers.

Replace the battery when the LED is dim or does not light. For instructions,

refer to “Changing the Battery.”

Mode Switch

Switches the sound variation.

S (Standard)

Reproduces the original HM-2 sound by

a newly crafted all analog circuit.

C (Custom)

This gives you a custom sound that’s

been tuned up to be even more

aggressive.

[DIST.] knob

Rotating the knob clockwise increases the gain and distortion

eect.

* If you set this knob too high, the noise will increase and

oscillation may occur.

INPUT jack

Electric guitar

This jack accepts input signals

(coming from a guitar, some other

musical instrument, or another

eects unit).

* The INPUT jack doubles as the power switch.

Power to the unit is turned on when you plug into the

INPUT jack; the power is turned o when the cable is

unplugged. To prevent unnecessary battery consumption,

be sure to disconnect the plug from the INPUT jack when

not using the eects unit.

Thumbscrew

When this screw is loosened, the

pedal will open, allowing you to

change the battery.

* For instructions on changing

the battery, refer to “Changing

the Battery.”

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	HM-2W

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss HM-2W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

17 November 2024

17 November 2024

3 September 2024

2 September 2024

Boss Gigcaster 8 GSC-8 Manual

1 September 2024

Boss TU-80 Manual

31 August 2024

Boss Reverb RV-6 Manual

31 August 2024

Boss Reverb RV-200 Manual

28 August 2024

Boss GKC-AD Manual

25 August 2024

Boss SDE-3000D Manual

25 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron Overbridge Manual

26 November 2024

Elektron Sidstation Manual

26 November 2024

SKROSS World Adapter Pro+ Manual

26 November 2024

SKROSS PRO – World & USB Manual

26 November 2024

SoundTube IPD-RS82-EZ Manual

26 November 2024

Kramer 4x1VB Manual

26 November 2024

Kramer RC-63A Manual

26 November 2024

SoundTube IPD-HP82-EZ Manual

26 November 2024

Kramer RK-KVM-1U-PP3 Manual

26 November 2024

Gioteck VX-2 (PS3) Manual

26 November 2024