Boss Metal Zone MT-2 Manual

Boss Ikke kategoriseret Metal Zone MT-2

Læs nedenfor 📖 manual på dansk for Boss Metal Zone MT-2 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

AC Adaptor

(PSA series; sold separately)

Electric Guitar

English

LEVEL knob

This knob adjusts the volume of the eect sound. Set this knob so that there will

be no dierence in volume between the eect and straight sounds.

* No sound will be heard when this knob is rotated completely

counterclockwise.

7The MT-2 is compact yet creates powerful eect pedal which, through the use of high-level gain circuits, creates heavy distortion and sustain eects.

7The MT-2 includes a three-band equalizer, Low, Middle and High. The middle band EQ is adopted for parametric type.

OUTPUT jack

Connect an amplier or other eect unit to this

jack.

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play

without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it

with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the

AC adaptor gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

* If the AC adaptor is connected while power is on, the power supply is

drawn from the AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

* The CHECK indicator shows whether the eect is on or o, and indicates the dierent

functions. It does not indicate whether the power to the device is on or not.

EQUALIZER HIGH knob

This knob controls the tone of the eect sound at higher frequencies.

Rotating the knob clockwise boosts the higher frequencies, while rotating it

counterclockwise cuts the higher frequencies. Higher frequencies have a variable

range of ±15 dB.

Pedal Switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the

Battery.”

Panel Descriptions

Main Features

Precautions When Connecting

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

* Once the connections have been completed, turn on power

to your various devices in the order specied. By turning on

devices in the wrong order, you risk causing malfunction and/

or damage to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

* Before turning the unit on/o, always be sure to turn the

volume down. Even with the volume turned down, you might

hear some sound when switching the unit on/o. However,

this is normal and does not indicate a malfunction.

Operating the Unit

1. When you have made the

necessary connections, set

the knobs as shown in the

illustration.

2. Press the Pedal Switch.

Make sure the CHECK indicator lights.

3. Adjust the level of distortion

using the DIST knob.

Rotating the knob clockwise

increases the distortion level

while rotating it counterclockwise

decreases it.

* If this knob is set too high, the noise

will increase and oscillation may occur.

4. Adjust the tone of the middle

range with the EQUALIZER

MIDDLE knob.

Rotating the knob clockwise boosts

the frequency while rotating it

counterclockwise cuts it.

5. Set the middle frequency (to be boosted or cut) with the

EQUALIZER MID FREQ knob.

* When the EQUALIZER MIDDLE knob is set to the center position, moving

the EQUALIZER MID FREQ konb does not aect the sound.

6. Adjust the tone of the high range

with the EQUALIZER HIGH knob.

Rotating the knob clockwise boosts

the higher frequencies while rotating

it counterclockwise cut them.

7. Adjust the tone of the low range

with the EQUALIZER LOW knob.

Rotating the knob clockwise boosts the lower frequencies while

rotating it counterclockwise cut them.

8. Using the LEVEL knob, adjust the

volume of the eect sound so

that there will be no dierence in

volume between the eect and

straight sounds.

Use of Battery

* A battery was installed in the unit before it left the factory. The

life of this battery may be limited, however, since its primary

purpose was to enable testing.

* If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES” (supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

* Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent

malfunction and damage.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be

opened without

detaching the

thumbscrew

completely.

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and

battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Main Specications

BOSS MT-2: Metal Zone

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply DC 9 V: Dry battery 6F22 (9 V) type (carbon),

AC Adaptor (PSA-series: optional)

Current Draw 30 mA

* Expected battery life under continuous use:

Carbon: Approx. 12.5 hours

Alkaline: Approx. 23.5 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 385 g/14 oz (including battery)

Accessories Owner’s Manual, Leaet (“USING THE UNIT

SAFELY,” “IMPORTANT NOTES,” and “Informa-

tion”), Dry battery/9 V type (6F22)

Options AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

EQUALIZER MIDDLE knob

This knob boosts or cuts the frequency you set with the EQUALIZER MID FREQ

knob. Rotating the knob clockwise boosts the level of the middle frequencies,

while rotating it counterclockwise cuts the level of the middle frequencies.

EQUALIZER MID FREQ knob

This knob sets the frequency of the middle range (200 Hz to 5 kHz). Rotating the

knob clockwise raises the frequency. Rotating it counterclockwise lowers the

frequency.

* When the EQUALIZER MID FREQ knob is set to the center position,

the EQUALIZER MID FREQ knob does not aect the sound.

DIST knob

This knob controls the intensity of the distortion eect. Rotating the knob

clockwise increases the distortion level.

* If you set this knob too high, the noise will increase and oscillation

may occur.

Sample Settings

Heavy Metal

Hard Rock

Overdrive

Fuzz

British Rock

Rock 1

Rock’n’roll

Rock 2

EQUALIZER LOW knob

This knob controls the tone of the eect sound at lower frequencies. Rotating the

knob clockwise boosts the lower frequencies, while rotating it counterclockwise

cuts the lower frequencies. The lower frequencies have a variable range of ±15

dB.

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another eects unit).

* The INPUT jack also serves as the power

switch. Power is turned on whenever a plug

is inserted into the INPUT jack, and is turned

o when the plug is disconnected. When

not using the unit, you should disconnect

any cord connected to the INPUT jack.

* 5 1 0 0 0 6 9 0 3 1 - 0 1 *

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	Metal Zone MT-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss Metal Zone MT-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

Boss BC-1X Manual

16 December 2024

Boss Super Chorus CH-1 Manual

16 December 2024

Boss Bass Equalizer GEB-7 Manual

16 December 2024

Boss Turbo Distortion DS-2 Manual

16 December 2024

Boss Multi Overtone MO-2 Manual

16 December 2024

Boss Tera Echo TE-2 Manual

16 December 2024

Boss Metal Core ML-2 Manual

16 December 2024

Boss Delay DM-2W Manual

16 December 2024

Boss NS-1X Manual

17 November 2024

Boss GT-1B Manual

17 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona AT-DVIF30S-IR Manual

29 December 2024

Atlona AT-PRO3HD66M Manual

29 December 2024

Atlona AT-3GSDI500 Manual

29 December 2024

BlueBuilt BBMAG2M Manual

29 December 2024

Atlona AT-3GSDI-14 Manual

28 December 2024

Atlona AT-COMP10SS Manual

28 December 2024

Atlona AT-2VGA300SL Manual

28 December 2024

Atlona AT-HD-V216 Manual

28 December 2024

Atlona AT-VGA11S Manual

28 December 2024

True TC900 Manual

28 December 2024