Boss Metal Zone MT-2WÙ Manual

Boss Ikke kategoriseret Metal Zone MT-2WÙ

Læs nedenfor 📖 manual på dansk for Boss Metal Zone MT-2WÙ (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

* 5100063492- 02*

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

AC Adaptor

(PSA series; sold separately)

Electric Guitar

English

EQUALIZER LOW knob

This knob controls the tone of the eect sound at lower frequencies. Rotating the

knob clockwise boosts the lower frequencies, while rotating it counterclockwise

cuts the lower frequencies. The lower frequencies have a variable range of ±15 dB.

EQUALIZER HIGH knob

This knob controls the tone of the eect sound at higher frequencies. Rotating the

knob clockwise boosts the higher frequencies, while rotating it counterclockwise

cuts the higher frequencies. Higher frequencies have a variable range of ±15 dB.

5This is a WAZA CRAFT series eect pedal crafted with a high-quality analog original circuit design.

5This unit produces a wide range of harmonically rich and powerful high-gain distortion sounds.

5This unit also includes a Custom setting providing an even broader range of dynamics and response.

OUTPUT jack

Use this 1/4” output jack to connect to the input of

your guitar amplier or the input of additional eect

unit.

Guitar Amplier

DC IN jack

In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (BOSS PSA series;

sold separately).

* Use only the specied AC adaptor (PSA series; sold separately), and connect it to an AC outlet

of the correct voltage.

* If the AC adaptor is connected while a battery is installed, the power supply is drawn from the

AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace

the battery when the LED is dim or does not light. For instructions, refer to “Changing

the Battery.”

* The CHECK indicator shows whether the eect is on or o, and indicates the dierent

functions. It does not indicate whether the power to the device is on or not.

Pedal switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the

Battery.”

Panel Descriptions

Main Features

Precautions When Connecting

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

* Once the connections have been completed, turn on power

to your various devices in the order specied. By turning on

devices in the wrong order, you risk causing malfunction and/

or damage to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

* Before turning the unit on/o, always be sure to turn the

volume down. Even with the volume turned down, you might

hear some sound when switching the unit on/o. However,

this is normal and does not indicate a malfunction.

Use of Battery

* The life of the included battery may be limited as its primary

purpose was for testing during assembly.

* If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES” (supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

* Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent

malfunction and damage.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be

opened without

detaching the

thumbscrew

completely.

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and

battery housing.

5. Finally, hold down the pedal while tightening the

thumbscrew into the guide bush hole.

Main Specications

BOSS MT-2W: Metal Zone

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply

DC 9 V: Alkaline battery (9 V, 6LR61),

Carbon-zinc battery (9 V, 6F22), AC adaptor

(sold separately)

Current Draw

35 mA

* Expected battery life under continuous

use:

Alkaline battery: Approx. 18 hours

Carbon-zinc battery: Approx. 7 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight

(including battery)

440 g

1 lb

Accessories

Owner’s Manual, Leaet (“USING THE

UNIT SAFELY,” “IMPORTANT NOTES,” and

“Information”), Alkaline battery (9 V, 6LR61)

Option

(sold separately) AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

* Roland, BOSS, METAL ZONE, and WAZA CRAFT are either

registered trademarks or trademarks of Roland Corporation in

the United States and/or other countries.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

Battery

EQUALIZER MID FREQ knob

This knob adjust the frequency of the Middle knobs gain. Rotating the knob

clockwise increases the frequency center point. At Max the frequency center is 5

kHz. Rotating the knob counterclockwise decreases the frequency center point.

At Minimum the frequency center is 200 Hz.

EQUALIZER MIDDLE knob

This knob boosts or cuts the frequency you set with the EQUALIZER MID FREQ

knob. Rotating the knob clockwise boosts the level of the middle frequencies,

while rotating it counterclockwise cuts the level of the middle frequencies.

* When the EQUALIZER MIDDLE knob is set to the center position, the

EQUALIZER MID FREQ knob does not aect the sound.

DIST knob

Rotating the knob clockwise increases the gain and distortion eect.

* If you set this knob too high, the noise will increase and oscillation

may occur.

LEVEL knob

This knob adjusts the volume of the eect sound.

* No sound will be heard when this knob is rotated completely

counterclockwise.

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another eects unit).

* The INPUT jack also serves as the power

switch. Power is turned on whenever a plug

is inserted into the INPUT jack, and is turned

o when the plug is disconnected. When

not using the unit, you should disconnect

any cord connected to the INPUT jack.

Mode switch

Switches the sound variation.

S (Standard)

Reproduces the original MT-2 sound by a newly

crafted all analog circuit.

C (Custom)

Produces a custom sound which is ne-tuned for

broader range of dynamics and response.

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	Metal Zone MT-2WÙ

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss Metal Zone MT-2WÙ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

Boss BC-1X Manual

16 December 2024

Boss Super Chorus CH-1 Manual

16 December 2024

Boss Bass Equalizer GEB-7 Manual

16 December 2024

Boss Turbo Distortion DS-2 Manual

16 December 2024

Boss Multi Overtone MO-2 Manual

16 December 2024

Boss Tera Echo TE-2 Manual

16 December 2024

Boss Metal Core ML-2 Manual

16 December 2024

Boss Delay DM-2W Manual

16 December 2024

Boss NS-1X Manual

17 November 2024

Boss GT-1B Manual

17 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona AT-DVIF30S-IR Manual

29 December 2024

Atlona AT-PRO3HD66M Manual

29 December 2024

Atlona AT-3GSDI500 Manual

29 December 2024

BlueBuilt BBMAG2M Manual

29 December 2024

Atlona AT-3GSDI-14 Manual

28 December 2024

Atlona AT-COMP10SS Manual

28 December 2024

Atlona AT-2VGA300SL Manual

28 December 2024

Atlona AT-HD-V216 Manual

28 December 2024

Atlona AT-VGA11S Manual

28 December 2024

True TC900 Manual

28 December 2024