Boss SY-1 Manual

Boss Ikke kategoriseret SY-1

Læs nedenfor 📖 manual på dansk for Boss SY-1 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

* 5 1 0 0 0 6 6 0 8 4 - 0 2 *

FS-7

FS-5U FS-6

For the USA

SUPPLIER’S DECLARATION OF CONFORMITY

Compliance Information Statement

Model Name :

Type of Equipment :

Responsible Party :

Address :

Telephone :

SY-1

Guitar Eects

Roland Corporation U.S.

5100 S. Eastern Avenue Los Angeles, CA 90040-2938

(323) 890-3700

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

English

List of Types

TYPE Explanation

LEAD 1/2 Sounds suitable for solo or lead.

PAD Soft sounds that ll-in gaps between notes.

BASS Bass synth sounds.

STR Synth strings sounds.

ORGN Organ sounds.

BELL Sounds with metallic resonance.

SFX 1/2 Sound eects or distinctive sounds.

SEQ 1/2 Sounds whose pitch or character changes rhythmically.

Precautions When Connecting

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

* Once the connections have been completed, turn on power

to your various devices in the order specied. By turning on

devices in the wrong order, you risk causing malfunction and/

or damage to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

* Before turning the unit on/o, always be sure to turn the

volume down. Even with the volume turned down, you might

hear some sound when switching the unit on/o. However,

this is normal and does not indicate a malfunction.

* Do not use connection cables that contain a built-in resistor.

* Use only the specied expression pedal. By connecting any

other expression pedals, you risk causing malfunction and/or

damage to the unit.

* You must turn o the power when connecting or

disconnecting an external footswitch. If you connect or

disconnect a footswitch while the power is on, the SOUND

HOLD function might remain on, or might not work. If the

SOUND HOLD function remains on or does not work, turn the

power o and then on again.

* When using this unit together with another eect unit, this

unit must be connected at the beginning of the chain. If an

eect-processed guitar or bass sound is input to this unit, it

might not work correctly.

Use of Battery

* The life of the included battery may be limited as its primary

purpose was for testing during assembly.

* If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES” (supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

* Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent

malfunction and damage.

* If operating this unit on battery, please use alkaline battery.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be

opened without

detaching the

thumbscrew

completely.

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and

battery housing.

5. Finally, hold down the pedal while tightening the

thumbscrew into the guide bush hole.

Main Specications

BOSS SY-1: Synthesizer

Nominal Input Level -20 dBu

Input Impedance 2.2 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply DC 9 V: Alkaline battery (9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw

85 mA

* Expected battery life under continuous

use:

Alkaline battery: Approx. 3 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight

(including battery)

450 g

1 lb

Accessories

Owner’s Manual, Leaet (“USING THE UNIT

SAFELY,“ “IMPORTANT NOTES,“ and “Informa-

tion“), Alkaline battery (9 V, 6LR61)

Option

(sold separately)

AC adaptor (PSA-series)

Footswitch: FS-5U

Dual footswitch: FS-6, FS-7

Expression pedal: FV-500H, FV-500L, EV-30,

Roland EV-5

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

* Roland and BOSS are either registered trademarks or

trademarks of Roland Corporation in the United States and/or

other countries.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

Battery

INPUT jack

This jack accepts input signals coming from a guitar or bass.

Guitar/BASS

SEND/RETURN jacks

Connect the SEND jack to the input, and RETURN jack to

the output of an eect unit that you’re using to process

the audio signal of your guitar/bass.

OUTPUT jack

Use this 1/4” output jack to connect to the input of

your guitar amplier or the input of additional eect

unit.

Guitar Amp

DC IN jack

In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (BOSS PSA series;

sold separately).

* Use only the specied AC adaptor (PSA series; sold separately), and connect it to an AC outlet

of the correct voltage.

* If the AC adaptor is connected while a battery is installed, the power

supply is drawn from the AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace

the battery when the LED is dim or does not light. For instructions, refer to “Changing

the Battery.”

* The CHECK indicator shows whether the eect is on or o, and indicates the dierent

functions. It does not indicate whether the power to the device is on or not.

TONE/RATE knob /DEPTH knob

These knobs adjust the sound of the eect that’s selected by TYPE and

VARIATION.

Pedal switch

This switch turns the eects ON/OFF.

SOUND HOLD function

1. When you hear the eect sound (synth sound) that you want to

hold, press the pedal switch once again and keep holding it down.

The hold function stays on while you keep holding down the pedal switch,

and the CHECK indicator blinks. You continue to hear the eect sound in

this state.

2. To turn o the hold function, take your foot o the pedal switch.

The CHECK indicator turns on, and the unit is in the normal eect-on state.

* If a footswitch is connected to the EXP/CTL jack, this function moves

from this unit to the footswitch.

Panel Descriptions

VARIATION knob

This knob selects variations 1–11 of the sound selected by TYPE.

GUITAR/BASS switch

This switch selects settings that are suitable for a guitar or a bass.

TYPE knob

This knob switches the type of synth sound.

(see the “List of Types” below)

EFFECT knob

This knob adjusts the volume of the eect sound (synth sound).

DIRECT knob

This knob adjusts the volume of the direct sound.

If a device is connected to the SEND/RETURN jacks, this knob adjusts its volume.

EXP/CTL jack You can connect an external footswitch (sold separately)

or expression pedal (sold separately) to this jack.

If a footswitch is connected, you can use the footswitch

to operate the SOUND HOLD function.

If a dual footswitch is connected, you can also control (in

addition to the SOUND HOLD function) either the pitch

or the tempo according to the sound that’s selected by

the knobs.

Pitch The pitch rises one octave while you hold down the switch.

Tempo You can enter the tempo by pressing the footswitch at the desired

interval.

If an expression pedal is connected, you can use it to control the TONE/RATE

eect. In this case, the position of the TONE/RATE knob is the maximum value of

the expression pedal.

Mode and polarity switch settings for the footswitch

Thumbscrew

When this screw is loosened, the

pedal will open, allowing you to

change the battery.

* For instructions on changing

the battery, refer to

“Changing the Battery.”

* The INPUT jack also serves as the

power switch. Power is turned on

whenever a plug is inserted into the

INPUT jack, and is turned o when

the plug is disconnected. When not

using the unit, you should disconnect

any cord connected to the INPUT

jack.

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	SY-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss SY-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

17 November 2024

17 November 2024

3 September 2024

2 September 2024

Boss Gigcaster 8 GSC-8 Manual

1 September 2024

Boss TU-80 Manual

31 August 2024

Boss Reverb RV-6 Manual

31 August 2024

Boss Reverb RV-200 Manual

28 August 2024

Boss GKC-AD Manual

25 August 2024

Boss SDE-3000D Manual

25 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron Overbridge Manual

26 November 2024

Elektron Sidstation Manual

26 November 2024

SKROSS World Adapter Pro+ Manual

26 November 2024

SKROSS PRO – World & USB Manual

26 November 2024

SoundTube IPD-RS82-EZ Manual

26 November 2024

Kramer 4x1VB Manual

26 November 2024

Kramer RC-63A Manual

26 November 2024

SoundTube IPD-HP82-EZ Manual

26 November 2024

Kramer RK-KVM-1U-PP3 Manual

26 November 2024

Gioteck VX-2 (PS3) Manual

26 November 2024