Boss VB-2W Manual


Læs nedenfor 📖 manual på dansk for Boss VB-2W (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Owners Manual
OUTPUT jack
Connect this jack to your amp or to the
input of another eect unit.
Guitar Amplier
DEPTH jack
If an expression pedal is connected, you can use the pedal
to control the depth of modulation.
* Refer to “Caution When Using the DEPTH Jack.
Precautions When Connecting
5 To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
5 Once the connections have been completed, turn on power to
your various devices in the order specied. By turning on devices
in the wrong order, you risk causing malfunction and/or damage
to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
5 Due to the characteristics of its analog circuitry, this units CHECK
indicator may be lit (eect on) or unlit (eect o) when you turn
the power on.
Use of Battery
5 A battery was installed in the unit before it left the factory. The life
of this battery may be limited, however, since its primary purpose
was to enable testing.
5 If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (supplied on a separate sheet).
5 When operating on battery power only, the units indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
5 Batteries should always be installed or replaced before connecting
any other devices. This way, you can prevent malfunction and
damage.
Changing the Battery
1. Hold down the pedal and loosen the thumbscrew, then
open the pedal upward.
* The pedal can be opened without detaching the thumbscrew
completely.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
2. Remove the old battery from the battery housing, and
remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil
spring, and battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Caution When Using the DEPTH Jack
5 Use only the specied expression pedal (BOSS FV-500H, FV-500L,
Roland EV-5; sold separately). By connecting any other expression
pedals, you risk causing malfunction and/or damage to the unit.
5 You can use the DEPTH knob to adjust the amount of modulation
that occurs when the pedal is in the maximum position.
5 You can use the minimum volume control of the EV-5 to adjust
the amount of modulation that occurs when the pedal is in the
minimum position.
Specications
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output
Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance 10 kΩ or greater
Power Supply Alkaline battery (9 V, 6LR61) (9 V, 6F22) or
Carbon-zinc battery
AC adaptor (PSA series: sold separately)
Current Draw 35 mA
* Expected battery life under continuous use:
Alkaline: 22 hours
Carbon: 4 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 450 g / 1lb 1 oz (including battery)
Accessories Leaet (“USING THE UNIT SAFELY, “IMPORTANT
NOTES, and “Information”)
Alkaline battery (9 V, 6LR61)
Options
(sold separately)
AC adaptor (PSA-series)
Expression pedal (BOSS FV-500H, FV-500L,
Roland EV-5)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
Thumbscrew
When this screw is loosened, the
pedal will open, allowing you to
change the battery.
* For instructions on changing
the battery, refer to “Changing
the Battery.
AC Adaptor
(PSA series: optional)
Electric Guitar
English
7This is a “WAZA CRAFT series” eect unit featuring analog circuitry painstakingly designed in every detail for the best possible sound.
7It is a vibrato unit featuring a unique eect that uses a carefully selected BBD.
7In addition to the sound of the original VB-2, you’ll enjoy a custom tone that’s been fully tuned-up by BOSS engineers.
Main Features
INPUT jack
This jack accepts signals coming from
a guitar or other musical instrument, or
another eects unit.
* The INPUT jack doubles as the power switch.
Power to the unit is turned on when you plug into the
INPUT jack; the power is turned o when the cable is
unplugged.
To prevent unnecessary battery consumption, be sure
to disconnect the plug from the INPUT jack when not
using the eects unit.
Panel Descriptions
DC IN jack
Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without
being concerned about how much battery power you have left.
* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the correct
voltage. Do not use any other AC adaptor, since this may cause malfunction.
* If the AC adaptor is connected while a battery is installed, the power supply is
drawn from the AC adaptor.
* We recommend that you keep batteries installed in the unit even though
you’ll be powering it with the AC adaptor. That way, you’ll be able to
continue a performance even if the cord of the AC adaptor gets accidently
disconnected from the unit.
CHECK indicator
This indicator shows whether the eect is on or o, and also doubles as the battery check
indicator. The indicator lights when the eect is on.
* If you’re powering the unit with a battery and the CHECK indicator goes dim— or doesn’t
light at all—when you try to turn the eect on, the battery is near depletion and should be
replaced. For instructions on changing the battery, refer to “Changing the Battery.
Pedal switch
This switch turns the eect on/o.
RATE knob
RISE TIME knob
DEPTH knob
Standard/Custom switch
MODE knob
Adjusts the modulation speed of the vibrato eect.
Adjusts the time until the maximum vibrato eect is reached.
Adjusts the modulation depth of the vibrato eect.
Switches the function of the pedal.
UNLATCH The vibrato eect is on only while you hold down the pedal.
BYPASS
The vibrato eect turns on/o each time you press the pedal.
Turning the vibrato eect o bypasses the BBD so that the audio
signal does not pass through it.
LATCH The vibrato eect turns on/o each time you press the pedal.
* When the vibrato eect is turned o in UNLATCH or LATCH mode, the
audio signal passes through the BBD so that the eect can begin smoothly.
Switches the tonal character.
Cable:
Stereo 1/4” phone type
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY and “IMPORTANT NOTES (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
S (standard) The original tone of the VB-2.
C (custom) A custom tone with emphasized modulation, in which the
frequency response also changes.
02
© 2016 Roland Corporation


Produkt Specifikationer

Mærke: Boss
Kategori: Ikke kategoriseret
Model: VB-2W

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss VB-2W stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Boss Manualer

Boss

Boss BC-1X Manual

16 December 2024
Boss

Boss Tera Echo TE-2 Manual

16 December 2024
Boss

Boss Metal Core ML-2 Manual

16 December 2024
Boss

Boss Delay DM-2W Manual

16 December 2024
Boss

Boss NS-1X Manual

17 November 2024
Boss

Boss GT-1B Manual

17 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona

Atlona AT-DVIF30S-IR Manual

29 December 2024
Atlona

Atlona AT-PRO3HD66M Manual

29 December 2024
Atlona

Atlona AT-3GSDI500 Manual

29 December 2024
BlueBuilt

BlueBuilt BBMAG2M Manual

29 December 2024
Atlona

Atlona AT-3GSDI-14 Manual

28 December 2024
Atlona

Atlona AT-COMP10SS Manual

28 December 2024
Atlona

Atlona AT-2VGA300SL Manual

28 December 2024
Atlona

Atlona AT-HD-V216 Manual

28 December 2024
Atlona

Atlona AT-VGA11S Manual

28 December 2024
True

True TC900 Manual

28 December 2024