Brother GS2786K Manual


Læs nedenfor 📖 manual på dansk for Brother GS2786K (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
4
5
2
3
1
4
Using Your Sewing
Machine
WARNING
Use only regular household electricity for the power source. Using other power
sources may result in re, electric shock, or damage to the machine.
Make sure that the plugs on the power cord are rmly inserted into the
electrical outlet and the power supply jack on the machine. Otherwise, a re or
electric shock may result.
Do not insert the plug on the power cord into an electrical outlet that is in poor
condition.
Turn off the main power and remove the plug in the following circumstances:
When you are away from the machine
After using the machine
When the power fails during use
When the machine does not operate correctly due to a bad connection or a
disconnection
During electrical storms
CAUTION
Use only the power cord included with this machine.
Do not use extension cords or multi-plug adapters with many other appliances
plugged in to them. Fire or electric shock may result.
Do not touch the plug with wet hands. Electric shock may result.
When unplugging the machine, always turn off the main power rst. Always
grasp the plug to remove it from the outlet. Pulling on the cord may damage
the cord, or lead to re or electric shock.
Do not allow the power cord to be cut, damaged, modied, forcefully bent,
pulled, twisted, or bundled. Do not place heavy objects on the cord. Do not
subject the cord to heat. These things may damage the cord and cause re
or electric shock. If the cord or plug is damaged, take the machine to your
authorized Brother Service Center for repairs before continuing use.
Unplug the power cord if the machine is not to be used for a long period of
time. Otherwise a re may result.
CAUTION
Always turn off the machine before
you change the needle. Otherwise,
injuries may occur if the foot
controller is accidentally pressed
and the machine starts sewing.
Only use sewing machine needles
for home use. Other needles may
bend or break and cause injury.
Never sew with a bent needle. A
bent needle will easily break and
cause injury.
Replacing the needle
Note
If a power outage occurs while the sewing machine
is being operated, turn off the main power and
unplug the power supply cord. When restarting the
sewing machine, follow the necessary procedure
to correctly operate the machine.
(For U.S.A. only)
This appliance has a polarized plug (one blade
wider than the other). To reduce the risk of electric
shock, this plug is intended to t in a polarized
outlet only one way. If the plug does not t fully in
the outlet, reverse the plug.
If it still does not t, contact a qualied electrician
to install the proper outlet. Do not modify the plug
in any way.
Connecting plugs
Main power and
sewing light switch
Foot controller
Checking the needle
Press the power switch
toward the “I” mark to turn the
main power and sewing light
on. Press toward the “O” mark
to turn off.
Press the foot
controller down to start
sewing. Take your foot
off the foot controller to
stop sewing.
CAUTION
Do not allow pieces of cloth
and dust to build up on
the foot controller. Doing
so could cause a re or an
electric shock.
Slower
Faster
1
2
3
CAUTION
Make sure you insert the needle until it
touches the stopper, and securely tighten
the needle clamp screw with a screwdriver,
otherwise the needle may break or the
machine may be damaged.
CAUTION
Before replacing the needle, place
fabric or paper under the presser foot
to prevent the needle from falling into
the hole in the needle plate.
Parallel space
Level surface
Turn the screw counterclockwise.
With the at side of
the needle toward the
back of the machine,
insert the needle until
touching this stopper.
Tighten the
needle clamp
screw.
Note
Do not use excessive
force when loosening
or tightening the needle
clamp screw.
XH2135-001
To sew in reverse,
push the reverse
sewing lever in as far
as possible and hold
it in that position while
you lightly push the foot
controller.
To sew forward, release
the reverse sewing
lever. The machine will
then sew forward.
The length of reverse
stitches is xed at 2 mm
(1/16 inch).
Reverse sewing
lever
Changing the presser foot
Sewing thin fabrics
Use a piece of fabric and
thread that are the same
as those used for your
project, and check the
thread tension and stitch
length and width.
Trial sewing
Stop the machine with
the needle in the fabric
at the point where you
want to change the
sewing direction, and
then raise the presser
foot lever. Using the needle as a pivot, turn
the fabric, lower the presser foot lever, and
then continue sewing.
Changing the sewing
direction
Sewing stretch
fabrics
Reverse sewing
When sewing thin
fabrics, the stitching
may become
misaligned or the
fabric may not feed
correctly. If this
occurs, place thin
paper or stabilizer
material under the
fabric and sew it
together with the
fabric. When you have
nished sewing, tear
off any excess paper.
First, baste
the pieces
of fabric
together,
and then
sew without
stretching the
fabric.
Basting
Stitching cylindrical pieces
2
1
Slide the at bed
attachment to the
left to release it.
Slide the part that you wish
to sew onto the arm, and
then sew from the top.
Note
When you are nished with free-arm sewing,
install the at bed attachment back in its
original position.
CAUTION
Always turn off the machine before you change
the presser foot. If you leave the power on and
step on the controller, the machine will start and
you may be injured.
Always use the correct presser foot for the
stitch pattern you have chosen. If you use the
wrong presser foot, the needle may strike the
presser foot and bend or break, and may cause
injury.
Only use presser feet that have been designed
to be used with this machine. Using any other
presser foot may cause accident or injury.
If the fabric does not t
easily under the presser
foot, raise the presser
foot lever even higher to
bring the presser foot to its
highest position.
Sewing thick fabrics
CAUTION
If fabric more than 6 mm (15/64 inch) thick is
sewn or if the fabric is pushed with too much
force, the needle may bend or break.
Mark on the wheel points up to raise
the needle.
Presser foot installation orientation
CAUTION
If the presser foot is
not installed with the
correct orientation, the
needle may strike the
presser foot, which
may bend or break
the needle and cause
injury.
CAUTION
If the stitches are bunched
together, lengthen the stitch
length and continue sewing.
Do not continue sewing
without lengthening the stitch
length, otherwise the needle
may break and cause injury.
CAUTION
After adjusting the stitch width,
slowly turn the handwheel toward you
(counterclockwise) and check that the
needle does not touch the presser foot. If
the needle hits the presser foot, the needle
may bend or break.
If the stitches are bunched together,
increase the stitch length. Continuing to
sew with the stitches bunched together may
result in the needle bending or breaking.
Stabilizer material
or paper
The main parts
a Bobbin winder
This winds the thread onto the bobbin for use as the lower thread.
b Stitch length dial
Rotate the dial to control the stitch length.
c Spool pin
This holds the spool of thread.
d Stitch width dial
Rotate the dial to control the stitch width.
e Upper tension-control dial
This controls the tension of the upper thread.
f Thread guide
This is used when winding the thread onto the bobbin and then
threading the machine.
g Thread take-up lever
h Thread cutter
Pass the threads through the thread cutter to cut them.
i Needle threader
j Quick-set bobbin
k Flat bed attachment with accessory compartment
l Presser foot
m Reverse sewing lever
Push this lever to stitch in the reverse direction.
n Pattern selection dial
Rotate the dial in either direction to choose the stitch you want.
oHandwheel
Used to manually raise and lower the needle.
p Buttonhole ne-adjustment screw
q Air vent
The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.
r Main power and sewing light switch
You can turn the main power and sewing light switch on and off.
s Foot controller jack / socket
Plug in the foot controller plug and connect the machine to the power supply.
t Presser foot lever
Used to raise and lower the presser foot.
u Handle
Carry the machine by its handle when transporting.
v Buttonhole lever (1-Step automatic buttonhole)
Lower the buttonhole lever when sewing buttonholes.
w Foot controller
You can use this to control the sewing speed, and to start and stop sewing.
Flat bed attachment
The accessories can be stored in
a compartment inside the at bed
attachment.
Slide the
attachment to the
left to open.
Storage compartment
Thread tension
Stitch length dial Stitch width dial
Correct tension
Correct tension is important as too
much or too little tension will weaken
your seams or cause puckers on
your fabric.
Lower thread
Upper thread
Upper tension-control dial
Surface of
fabric
Back of fabric
Upper tension is too tight
Loops will appear on the surface of the fabric.
Note
If the bobbin thread was incorrectly threaded, the
upper thread may be too tight. In this case, refer to
“1 Lower threading” on the back side to rethread
the bobbin thread.
Solution: Reduce the tension by turning the upper
tension control dial to a lower number.
Upper
thread Lower
thread
Loops appear on
surface of fabric
Back of fabric
Surface
of fabric
Solution: Increase the tension by turning the upper
tension control dial to a higher number.
Upper
thread Lower thread
Back of fabric
Note
If the upper thread was incorrectly threaded, the
upper thread may be too loose. In this case, refer to
“2 Upper threading” on the back side and rethread
the upper thread.
Note
(For U.S.A. only)
Foot Controller: Model KD-1902
This foot controller can be used
on the machine with product
code 888-X06, 888-X08, 888-X16,
888-X18, 888-X26 and 888-X28.
The product code is mentioned
on the machine rating plate.
Surface
of fabric
Upper tension is too loose
Loops appear on the back of the fabric.
Loops appear
on back of
fabric
The tension of the thread will affect the quality of your stitches. You may need to adjust it when you change fabric or thread. We recommend that you do a test sample on
scrap of a fabric before you start to sew.
Depending on the selected stitch, you may need to adjust the stitch
length for best results.
The numbers marked on the stitch length dial represent the stitch
length in millimeters (mm) (1/25 inch).
THE HIGHER THE NUMBER, THE LONGER THE STITCH. With the
“0” setting, material is not fed. This is used when sewing a button.
The “F”-“1” range is for making a satin stitch (closed zigzag stitch),
which is used for making buttonholes and decorative stitches. The
position needed for making the satin stitch varies according to the
material and thread being used. To determine the exact dial position,
rst test the stitch and length settings on a scrap piece of fabric to
observe the feeding of the material.
Raise the needle by turning the handwheel toward you
(counterclockwise) so that the mark on the wheel points up.
The numbers marked on the dial represent the stitch width.
When the Straight or Triple Stretch Stitch is
selected, the needle position can be changed from
left to right by adjusting the stitch width dial.
This snaps in
to the shank.
Press the black button at the
back of the presser foot holder
to release the presser foot.
9For repair or adjustment:
If the light unit (light-emitting diode) is damaged, it must be
replaced by authorized Brother Service Center.
In the event a malfunction occurs or adjustment is required,
rst follow the troubleshooting table in the back of the operation
manual to inspect and adjust the machine yourself. If the problem
persists, please consult your local authorized Brother Service
Center.
Use this machine only for its intended use as described in this manual.
Use accessories recommended by the manufacturer as contained in
this manual.
The contents of this manual and specications of this product are
subject to change without notice.
For additional product information, visit our web site at www.brother.
com
SAVE THESE INSTRUCTIONS
This machine is intended for household use.
FOR USERS IN COUNTRIES EXCEPT
CENELEC COUNTRIES
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
FOR USERS IN CENELEC COUNTRIES
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS
ONLY
IMPORTANT
In the event of replacing the plug fuse, use a fuse approved by
ASTA to BS 1362, i.e. carrying the mark, rating as marked on
plug.
Always replace the fuse cover. Never use plugs with the fuse cover
omitted.
If the available electrical outlet is not suitable for the plug supplied
with this equipment, you should contact your authorized Brother
Service Center to obtain the correct lead.
Operation
Manual
Sewing Machine
Please read these safety instructions before attempting to use the
machine.
DANGER
- To reduce the risk of electric shock:
1Always unplug the machine from the electrical outlet
immediately after using, when cleaning, when making any
user servicing adjustments mentioned in this manual, or if you
are leaving the machine unattended.
WARNING
-
To reduce the risk of burns, re, electric shock, or injury to persons.
2Always unplug the machine from the electrical outlet when
making any adjustments mentioned in the instruction manual:
To unplug the machine, switch the machine to the symbol “O”
position to turn it off, then grasp the plug and pull it out of the
electrical outlet. Do not pull on the cord.
Plug the machine directly into the electrical outlet. Do not use
an extension cord.
Always unplug your machine if the power is cut.
3Electrical Hazards:
This machine should be connected to an AC power source
within the range indicated on the rating label. Do not connect it
to a DC power source or inverter. If you are not sure what kind
of power source you have, contact a qualied electrician.
This machine is approved for use in the country of purchase only.
4Never operate this machine if it has a damaged cord or plug,
if it is not working properly, if it has been dropped or damaged,
or water is spilled on the unit. Return the machine to the nearest
authorized Brother dealer or service center for examination,
repair, electrical or mechanical adjustment.
While the machine is stored or in use if you notice anything
unusual, such as an odor, heat, discoloration or deformation, stop
using the machine and immediately unplug the power cord.
When transporting the machine, be sure to carry it by its handle.
Lifting the machine by any other part may damage the machine or
result in the machine falling, which could cause injuries.
When lifting the machine, be careful not to make any sudden or
careless movements, otherwise you may injure your back or knees.
5Always keep your work area clear:
Never operate the machine with any air openings blocked. Keep
ventilation openings of the machine and foot control free from the
build up of lint, dust, and loose cloth.
Do not store objects on the foot controller.
Do not use extension cords. Plug the machine directly into the
electrical outlet.
Never drop or insert any object into any opening.
Do not operate where aerosol (spray) products are being used or
where oxygen is being administered.
Do not use the machine near a heat source, such as a stove or
iron; otherwise, the machine, power cord or garment being sewn
may ignite, resulting in re or an electric shock.
Do not place this machine on an unstable surface, such as
an unsteady or slanted table, otherwise the machine may fall,
resulting in injuries.
6Special care is required when sewing:
Always pay close attention to the needle. Do not use bent or
damaged needles.
Keep ngers away from all moving parts. Special care is required
around the machine needle.
Do not turn on the machine while pressing down the foot controller.
The machine may start unexpectedly and cause personal injury or
damage to the machine.
Switch the machine to the symbol “O” position to turn it off when
making any adjustments in the needle area.
Do not use a damaged or incorrect needle plate, as it could cause
the needle to break.
Do not push or pull the fabric when sewing, and follow careful
instruction when freehand stitching so that you do not deect the
needle and cause it to break.
7This machine is not a toy:
Your close attention is necessary when the machine is used by or
near children.
The plastic bag that this machine was supplied in should be kept
out of the reach of children or disposed of. Never allow children to
play with the bag due to the danger of suffocation.
Do not use outdoors.
8For a longer service life:
When storing this machine, avoid direct sunlight and high humidity
locations. Do not use or store the machine near a space heater,
iron, halogen lamp, or other hot objects.
Use only neutral soaps or detergents to clean the case. Benzene,
thinner, and scouring powders can damage the case and machine,
and should never be used.
Always consult the operation manual when replacing or installing
any assemblies, the presser feet, needle, or other parts to assure
correct installation.
Please visit us at where you can get the http://s.brother/cpmaa/
support information (Instruction Videos, FAQs, etc.) for your Brother
product.
Be sure to read this document before using the machine.
We recommend that you keep this document nearby for future reference.
IMPORTANT SAFETY
INSTRUCTIONS
Shank
Black
button
Presser foot holder
Stitch length dial
Stitch width dial
Stitch
length dial
Shorter Longer
Product Code:
888-X06/X08/X16/X18/X26/X28
Install the twin needle in the
same way.
1
32
4
5
6
7
8
9
0
ABC
D
L
K
E
I
H
G
J
M
F


Produkt Specifikationer

Mærke: Brother
Kategori: Ikke kategoriseret
Model: GS2786K

Har du brug for hjælp?

Hvis du har brug for hjælp til Brother GS2786K stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Brother Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024