Buffalo BS-GU2008 Manual

Buffalo Skifte BS-GU2008

Læs nedenfor 📖 manual på dansk for Buffalo BS-GU2008 (2 sider) i kategorien Skifte. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

User Manual

BS-GU2008

Package Contents

The package contains the items shown below. If any items are missing,

please contact the dealer where you purchased the BS-GU2008 .

The appearance of the BS-GU2008 may vary from the illustration.

• Switch (main unit) ...................................................................................................... 1

• Power cable .................................................................................................................. 1

• Rubber feet .................................................................................................................. 4

• Serial number stickers ............................................................................................. 2

• User manual (this document) ................................................................................. 1

• Warranty ........................................................................................................................ 1

Layout

1.Indicators

Indicators are located on the front panel of the product. The functions of

each indicator are shown below.

Link/Act (Green)

On: Link established

Blinking: Data transfer

Blinking (1-second interval): Loop detected

Oﬀ: Link not established

1000/100/10M (Green or Orange)

On (Green): 1000 Mbps link

On (Orange): 100 Mbps link

Blinking (Green or Orange): Loop detected

Oﬀ: 10 Mbps link or no link

Loop (Red)

Blinking: Loop detected

Oﬀ: Normal

Power (Green)

On: Power on

Oﬀ: Power oﬀ

2. Loop detection switch

Switch loop detection on and oﬀ.

3. LAN ports

These are ports for connecting 1000BASET/100BASE-TX/10BASE-T devices.

4.Power connector

Connect the included power cable to this connector.

Loop Detection

This unit can detect network loops that can cause interference in the

network.

What Is a Loop?

If both ends of an Ethernet cable are connected to the same hub, or when

multiple connections exist between two hubs, data may be sent in a loop

around the network, wasting network capacity and never getting to its

destination. This continuously circulating data may interfere with other

network communication.

Loop Detection

･Oﬀ: Loops are not detected.

･On: If a network loop is detected, the link/act, 1000/100/10M, and loop

LED on the front of this unit blink once per second.

Turning Loop Detection On and Off

Use the switch on the front of the BS-GU2008 to turn loop detection on and

oﬀ.

2. Disconnect the power cable, then reconnect it.

Note: The setting isn't changed until power cable is disconnected and

reconnected.

Caution :

・ While loop detection is enabled, the BS-GU2008 will send a loop

detection packet through the network every two seconds. If these

packets disrupt your network in any way, disable loop detection.

・ Loop detection cannot detect or block all types of loops.

When a Loop is Detected

Reconnect the wiring, making sure that no wires are connected in a

loop.

Precautions for Installation

• Do not install the device in an unstable location such as on an unsteady

table or an inclined surface.

• Do not place another hub or object that generates heat on top of this

unit.

• Please route all cables properly to prevent people from tripping over

them.

• Ensure the air vents on the product are not blocked by other equipment

or walls.

• Only use the power cable included with the product. Using other power

cables may result in damage or ﬁre.

Floor or Shelf Mounting

Attach the supplied rubber feet to the bottom corners of the unit before

use.

Mounting to a Metal Surface

To mount to a metal surface, such as the side of a steel desk, use the

"BS-MGK-A Magnet Kit" (sold separately). Attach the supplied rubber feet to

the bottom corners of the unit before using the magnet kit.

Caution:

・ Do not put ﬂoppy discs, magnetic cards, or other magnetic storage

media near magnets. Doing so may delete or corrupt data.

・ If the switch is secured by the magnet alone, it should be no more than

75 cm (29.5 in) from the oor.

Mounting to a Wall

To mount the unit to a wall, use 2 screws (not included) with the dimensions

shown below. Install the screws 78 mm (3.1 in) apart and slide the mounting

holes in the base of the BS-GU2008 over them.

Installation

Use screws where this section is

2 mm (0.08 in) or less.

φ6 mm (0.24 in)

2 mm (0.08 in)

3mm (0.12 in)

1. Indicators

2. Loop detection switch

4. Power connector

3. LAN ports

Produkt Specifikationer

Mærke:	Buffalo
Kategori:	Skifte
Model:	BS-GU2008
Vekselstrømsindgangsspænding:	100 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	102 mm
Dybde:	180 mm
Højde:	30 mm
Vægt:	540 g
Brugervejledning:	Ja
Produktfarve:	Sort
Relativ luftfugtighed ved drift (H-H):	10 - 85 %
Driftstemperatur (T-T):	0 - 50 °C
Husmateriale:	Metal
Kabler inkluderet:	Vekselstrøm
Certificering:	VCCI A, UL60950-1, FCC A, IC A, VCCI A
Strømforbrug (maks.):	4 W
Netværksstandarder:	IEEE 802.3,IEEE 802.3ab,IEEE 802.3u,IEEE 802.3x
LED-indikatorer:	Ja
Maksimal dataoverførselshastighed:	1000 Mbit/s
Strøm over Ethernet (PoE):	Ingen
Switch-type:	Ikke administreret
10G understøttelse:	Ingen
Auto MDI/MDI-X:	Ja
Flowkontrol support:	Ja
Kobber ethernet kabelteknologi:	10BASE-T,100BASE-TX,1000BASE-T
Basis omskiftning RJ-45 Ethernet porte, antal:	8
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
Filtrering af MAC-adresser:	Ja
Loop beskyttelse:	Ja
Opbevar-og-frem:	Ja
MAC adresselabel:	8190 entries
Switch kapacitet:	16 Gbit/sek.
Jumbo Frames support:	Ja
Jumbo rammer:	9216
Stativ-montering:	Ja
Bufferstørrelse:	128 KB
Understøttede kabeltyper:	Cat3,Cat5,Cat5e
Pakke videresendelsesrate (1 Gbps):	1488095 pps
Pakke videresendelsesrate (100 Mbps):	148810 pps
Pakke videresendelsesrate (10 Mbps):	14881 pps
Gummifødder:	Ja