CaterChef 508125 Manual
CaterChef
Post maskine
508125
Læs nedenfor 📖 manual på dansk for CaterChef 508125 (2 sider) i kategorien Post maskine. Denne guide var nyttig for 53 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
508025-125 ma en 2013.01
P Srofes s iona l up p l ie s
*508.025 / 508.125 ELECTRIC PASTA COOKER - MANUAL
1/2
1 INSTRUCTION FOR THE INSTALLATION
1.1 Technical data
The data plate is near power cable, on the back of the machine and lists all the data needed for connecting
up to the mains.
2 INSTALLATION
The equipment must be positioned using a spirit level and adjusting the legs (screw/unscrew).
The main power switch or power outlet must be near the equipment in an easily accessible position.
We recommend installing the machine under an extractor hood so that vapors can be removed rapidly.
The machine should only be placed near walls, partitions or other kitchen furniture that are made of
fl ameproof materials.
Fire regulations must be strictly adhered to.
2.1 Legal requirements
Installation must be to the following standards:
- current accident prevention laws;
- CEI installation standards.
2.2 Installation
Installation, setup and maintenance must be carried out by qualifi ed personnel.
All installation work must be done in compliance with current regulations.
The manufacturer will accept no liability in relation to faulty operation due to defective or non compliant
installation.
WARNING! As required by international law, the equipment should only be connected up to the mains if
there is a omnipolar* circuit breaker upstream with a contact opening of at least 3 mm.
2.2.1 Electrical connection
The equipment is supplied with a power cable. If you have to replace this cable, make sure you use a
H07RN-F type and that its cross section is suffi cient for the equipment’s power rating.
To change the cable, pass it through the cable lead and connect the wires to the terminal block, which is
located in the cable lead on single phase machines and inside the equipment on three-phase machines.
Make sure the wires are connected to the terminal block correctly and tightly and then close the cable lead.
The yellow/green wire must be connected to the earth terminal.
2.2.1.1 Unipotential
The equipment must be connected to a unipotential system.
The connection screw is located in the rear of the housing and marked by the sign
WARNING! The manufacturer accepts no liability and will not refund under guarantee any damage caused
through installation that is improper or not compliant with the instructions.
2.3 Set up
The machine must be carefully cleaned (especially the tank, see section 4: Cleaning)
Produkt Specifikationer
Mærke: | CaterChef |
Kategori: | Post maskine |
Model: | 508125 |
Har du brug for hjælp?
Hvis du har brug for hjælp til CaterChef 508125 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Post maskine CaterChef Manualer
27 April 2023
12 November 2022
17 Oktober 2022
Post maskine Manualer
- Post maskine Bosch
- Post maskine SilverCrest
- Post maskine Philips
- Post maskine Rommelsbacher
- Post maskine Kenwood
- Post maskine Witt
- Post maskine Ernesto
- Post maskine Livoo
- Post maskine Klarstein
- Post maskine Bartscher
- Post maskine Ariete
- Post maskine C3
- Post maskine Cuisinart
- Post maskine G3 Ferrari
- Post maskine Gourmetmaxx
- Post maskine Hamilton Beach
- Post maskine Unold
- Post maskine Bellini
- Post maskine Imperial
- Post maskine Laica
- Post maskine Trebs
- Post maskine Beper
- Post maskine Emeril Lagasse
- Post maskine Arendo
- Post maskine Waring Commercial
- Post maskine Manta
- Post maskine Nutrichef
- Post maskine Farberware
- Post maskine Marcato
- Post maskine Ronco
- Post maskine Girmi
- Post maskine Riviera And Bar
- Post maskine CombiSteel
- Post maskine Proluxe
- Post maskine DoughXpress
- Post maskine Estella
- Post maskine Weston
- Post maskine Imperia
- Post maskine Stilfer
- Post maskine Tescoma
Nyeste Post maskine Manualer
13 September 2024
6 September 2024
3 September 2024
3 September 2024
1 September 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
30 August 2024