Cateye Enduro 8 CC-ED300 Manual

Cateye Cykelcomputer Enduro 8 CC-ED300

Læs nedenfor 📖 manual på dansk for Cateye Enduro 8 CC-ED300 (2 sider) i kategorien Cykelcomputer. Denne guide var nyttig for 31 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Important
Note
Warning
• Pay attention to the road or trail! Do not be distracted by the
computer.
• Be sure to securely mount the magnet, the sensor, and the
bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws are not loosen.
• Keep batteries out of reach of small children. Dispose of batter-
ies according to local regulations.
• Avoid unnecessary prolonged exposure to the sun. Never at-
tempt to disassemble the computer head.
• Don’t use thinner, benzene or alcohol to wipe the surface of the
computer. They may damage the surface of computer.
Computer Set-up (For 1st use or after replacing the battery)
All Clear
Push three buttons (MODE, START/
STOP and SET) at the same time.
* Do this procedure without fail for
stable measurement when you use
this system for the first time and every
time the battery is replaced.
1
Starting the odom-
eter from zero.
Retaining the current odometer reading
(the odometer starts from the reading you
inputted)
SET
MODE
MODE
ST/STOP
ST/STOP
Set The Tire Circumference
Set the tire circumference in cm.
Note
You can easily set it by referring to the chart shown
right.
Setting is completed by pushing the SET button.
3
Increase the
number.
Max. 300 cm
Decrease
the number
Min. 100 cm
Preparation Complete.
(the screen will show the time measurement in this state)
* The auto mode is ON in this state.
MODE Button
START/STOP Button
SET Button
!
L(cm)
14 x 1.50 102
14 x 1.75 106
16 x 1.50 119
16 x 1.75 120
18 x 1.50 134
18 x 1.75 135
20 x 1.75 152
20 x 1-3/8 162
22 x 1-3/8 177
22 x 1-1/2 179
24 x 1 175
24 x 3/4Tubular 178
24 x 1-1/8 179
24 x 1-1/4 191
24 x 1.75 189
24 x 2.00 192
24 x 2.125 196
26 x 7/8 192
26 x 1(59) 191
26 x 1(65) 195
26 x 1.25 195
26 x 1-1/8 190
26 x 1-3/8 207
26 x 1-1/2 210
26 x 1.40 200
26 x 1.50 201
26 x 1.75 202
26 x 1.95 205
26 x 2.00 206
26 x 2.10 207
26 x 2.125 207
26 x 2.35 208
26 x 3.00 217
27 x 1 215
27 x 1-1/8 216
27 x 1-1/4 216
27 x 1-3/8 217
650 x 35A 209
650 x 38A 212
650 x 38B 211
700 x 18C 207
700 x 19C 208
700 x 20C 209
700 x 23C 210
700 x 25C 211
700 x 28C 214
700 x 30C 217
700 x 32C 216
700C Tubular 213
700 x 35C 217
700 x 38C 218
700 x 40C 220
L cm
SET
ST/STOP
MODE
Contact Point
Select The Measurement Unit
Select the measurement unit, kilometer
or mile, by pushing the MODE button.
2
MODE
Choose Either of The Followings.
• When you want to input the reading of the currently
used odometer, keep pressing the MODE button for
two seconds and input the reading.
• When you want to start the odometer from zero,
push the START/STOP button.
Kilometer Mile
SET Button
MODE Button
START/STOP
Button
Input the current reading of odometer.
For two seconds.
Increase the
number.
Move the
decimal point.
You need to know the tire
circumference (L cm) be-
forehand.
Tire size
Tire size is usually shown
on the sidewall of tires.
®
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending
Copyright © 2002 CAT EYE Co. Ltd.
CCMED3-021210 066600240 1
5
3
37
3
5
5
OK
1
2
4
3
7
5 6 8
3
2
1
8
7
ENDURO8
8
1
7
1
6
Installation of the Computer on Your Bike
The computer is combined with the following parts.
Mount The Bracket
Secure the cord on the fork with the nylon ties and lead to the handle bar along the outer7
cable of the bicycle by means of the spiral tube 8.
Put the rubber pad on the bracket and secure the bracket on the handle bar with the6 1
screw. Slide the computer into the bracket 1 until you hear the click sound.
The contact points are automatically closed. When you need to detach the computer, slide
forward the computer with the lever pushed simultaneously.
Note
Allow enough wire clearance in the area marked with an to insure that you can
turn the handlebar from left to right without pulling the wire.
Test The Basic Functions
Rotate the front wheel gently and see if the computer indicates the
running speed.
Note
When the computer does not indicate the speed, check
the position of the magnet and the sensor.
4
1 Bracket
2 Cord
3 Sensor
4 Sensor Rubber Pad
Center
5Magnet
6Bracket Rubber Pad
7Five Nylon Ties
8Spiral Tube
Front Fork
3
2
1
Please read these instructions carefully before attempting to
install and use your CAT EYE ENDURO 8 computer so that you
understand the functions of this product.
Please don’t throw away this manual, Keep the manual at a place easily accessible.
CAT EYE ENDURO 8
CYCLOCOMPUTER CC-ED300
E: Owner’s Manual
Spoke
Rotate the front wheel.
Front Fork
Sensor Side
Within 5 mm
Marked Line
Mount sensor and adjust the gap between the
magnet and the sensor.
Secure the sensor with the larger nylon ties 3 7 at
the appropriate place and in the right direction.
Mount the magnet
5 on a spoke of the front wheel so that the surface
of the magnet will face the sensor.
Lever
Important Note
Mount the sensor at the appropri-3
ate position so that the center of the
magnet 5 will align with the
marked line on the sensor when the
wheel is rotated.
Important Note
Rotate the sensor on the front fork to
adjust the gap between the sensor
and the magnet within 5 mm, and5
secure it with the nylon ties.
1
You can refer to the guide
chart to roughly know the
tire circumference.

Produkt Specifikationer

Mærke: Cateye
Kategori: Cykelcomputer
Model: Enduro 8 CC-ED300

Har du brug for hjælp?

Hvis du har brug for hjælp til Cateye Enduro 8 CC-ED300 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Cykelcomputer Cateye Manualer

Cateye

Cateye Commuter CC-COM10W Manual

16 December 2024
Cateye

Cateye Stealth 10 CC-GL10 Manual

9 December 2024
Cateye

Cateye Strada Smart CC-RD500B Manual

16 November 2024
Cateye

Cateye Padrone Smart plus CC-SC100B Manual

23 Maj 2024
Cateye

Cateye Double Wireless CC-CD300DW Manual

14 April 2024
Cateye

Cateye Stealth evo CC-GL11 Manual

3 April 2024
Cateye

Cateye Velo 9 Manual

14 Marts 2024
Cateye

Cateye Strada CC-RD410DW Manual

27 Februar 2024
Cateye

Cateye e-Train Data IF-TR100 Manual

15 Februar 2024
Cateye

Cateye Strada CC-RD400DW Manual

4 December 2023

Cykelcomputer Manualer

Nyeste Cykelcomputer Manualer

IGPSport

IGPSport iGS630S Manual

14 November 2024
Bosch

Bosch eBike Purion Manual

7 November 2024
Pro

Pro phete BW 020 Manual

7 November 2024
Velomann

Velomann C17 Manual

6 Oktober 2024
Velomann

Velomann C8 Manual

6 Oktober 2024
Velomann

Velomann VDOUBLE 10 Manual

6 Oktober 2024
LeMond Fitness

LeMond Fitness Pilot II Manual

20 September 2024
LeMond Fitness

LeMond Fitness Pilot Manual

20 September 2024
VDO

VDO X10W Manual

18 August 2024
Contec

Contec C-500 Manual

17 August 2024