Chamberlain 041-0200-000 Manual

Chamberlain Lys 041-0200-000

Læs nedenfor 📖 manual på dansk for Chamberlain 041-0200-000 (4 sider) i kategorien Lys. Denne guide var nyttig for 28 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
Integrated LED Light Module
Replacement
Repair Parts 041-0200-000, 041-0201-000,
041-0202-000 and 041-0203-000
To prevent possible SERIOUS INJURY or DEATH:
Disconnect ALL electric and battery power BEFORE performing ANY
service or maintenance.
To prevent damage to the receiver logic board, DO NOT touch printed
circuit board of replacement receiver/logic board during installation.
ALWAYS wear protective gloves and eye protection when changing the
battery or working around the battery compartment.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Introduction
Use this instruction to replace the integrated LED light module. The images
throughout this manual are for reference only and your product may look
different.
You will need:
1/4" magnetic nut driver
Long-nosed pliers
5/16" long-shafted magnetic nut driver and socket
Flathead screwdriver
Instructions
1. Disconnect the electrical and battery power (if applicable) to the garage
door opener. Remove the battery and place in a safe location.
2. Remove the control door panel from both ends of
the opener. (A)
a. Separate the hinges in
opposite directions.
b. Remove the panels from
the hinge setting and
place in a safe location.
3. Disconnect the door control
wires from the RED and
WHITE terminals and the
safety reversal sensor wires
from the BLACK and WHITE
terminals. (B)
4. Remove the end panels from
both ends of the opener.
5. Remove the integrated LED
light module from the
opener. (C)
6. Disconnect the ORANGE and WHITE wire harness from plug to the
integrated LED light module and set aside cover / LED light module. (D)
7. Install the new integrated LED light module.
8. Connect the ORANGE and WHITE wire harness from the plug to the
Integrated LED Light Module. (D)
9. Align integrated LED light module to chassis screw holes.
10. Attach both end panels.
11. Reconnect the door control and safety reversal sensor wires. (B)
Door Control:
WHITE wire into the WHITE terminal.
WHITE/RED wire into the RED terminal.
Safety Reversal Sensors:
WHITE wires into the WHITE terminal.
WHITE/BLACK wires into the GRAY terminal.
12. Reattach the control door panels.
13. Reconnect power to the opener.
14. Test the Protector System.
RED
WHITE
WHITE
GREY
B
A
D
C
Integrated LED Light Module
Control Door Panel
End Panel


Produkt Specifikationer

Mærke: Chamberlain
Kategori: Lys
Model: 041-0200-000

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain 041-0200-000 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys Chamberlain Manualer

Lys Manualer

Nyeste Lys Manualer

Nanlite

Nanlite D672BII Manual

19 December 2024
Nanlite

Nanlite Compac 40 Manual

19 December 2024
Nanlite

Nanlite MixPad II 11C Manual

18 December 2024
Nanlite

Nanlite D672II Manual

18 December 2024
Chauvet

Chauvet WELL POD 2X6 Manual

17 December 2024
Luxli

Luxli ORC-VIOLA-M2 Manual

17 December 2024
Makita

Makita DML817 Manual

16 December 2024
Makita

Makita MT001 Manual

16 December 2024