Chamberlain CLLP1 Manual
Chamberlain
Garage døråbner
CLLP1
Læs nedenfor 📖 manual på dansk for Chamberlain CLLP1 (3 sider) i kategorien Garage døråbner. Denne guide var nyttig for 28 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/3
White GreyRed
Wire Nut
Connection
Wire
White
Connection
Wire
White/Black
Connection
Wire
Parking Assist
Wires
Safety
Sensor
Wires
Insert Into Appropriate Terminals
®Models CLLP1 and CLLP1C
Chamberlain Laser Garage Parking Assist
Owner’s Manual
To avoid eye INJURY or damage to product:
• NEVER point the laser at anyone.
• NEVER look directly into the laser beam.
• NEVER disassemble the laser.
• The parking assist is NOT a substitute for safe parking practices.
• Use of controls or adjustments, or the performance or procedures
other than specified can result in hazardous radiation exposure.
• ONLY for use on Chamberlain manufactured garage door openers.
CAUTION
CAUTION
CAUTION
CAUTIONCAUTION
Figure 1
Figure 2
Figure 3
Figure 4
Insert Into Appropriate Terminals
Red White Grey
Parking Assist
Wires
Safety Sensor
Wires
Parking Assist
For Service Dial Our Toll Free Number:
U.S.: 1-800-528-9131 Canada: 1-800-654-4736
www.chamberlain-diy.com
INSTALLATION
1. Open yo r garage door and park yo r vehicle o tside of garage.u u u
2. Determine the mo nting location on the ceiling and fasten theu
parking assist sing screw and anchor (Fig re 1).u u
3. Depress tabs nder the wires and temporarily remove the whiteu
and white/black safety sensor wires from the garage door opener.
4. Stripping the wires prior to installation:
Installing one parking assist: Separate white and white/black
wires and strip 7/16" (11 mm) of ins lation from parking assistu
wires.
Installing two parking assists: Cut 6" (15 cm) of wires from the
end of one set of parking assist wires for se as connectionu
wires. Separate white and white/black wires and strip 7/16"
(11 mm) of ins lation from both ends of connection wire.u
5. Connecting the wires to garage door opener:
Installing one parking assist: Twist like colored wires for
parking assist and safety sensors together. Insert twisted wires
into q ick-connect holes: white to white and white/black to greyu
(Figure 2).*
Installing two parking assists: Separate white and white/black
wires and strip 7/16" (11 mm) of ins lation from the end ofu
parking assist wires. Twist like colored wires for parking assists,
safety sensors and connection wire together. Sec re with wireu
nut. Insert connection wires into quick-connect holes: white to
white and white/black to grey (Fig re 3).*u
* Please refer to your garage door opener owner’s manual for
proper wire installation.
SET UP AND ADJUSTMENT
1. Drive yo r vehicle into garage and park in the desired location.u
2. Activate the parking assist by obstr cting the path of the safetyu
sensors. The laser will emit a p lsing bright red beam (Fig re 4).u u
Aim the red beam to a location on the dash or hood that can
easily be seen while seated in the driver’s seat.
NOTE: The laser will shut off in 1 minute. If you are not finished
adjusting the beam and it turns off, simply obstruct the path of the
safety sensors.
3. Sit in the driver’s seat and confirm that yo can easily see theu
location of the red beam. This location is now yo r point ofu
reference for parking yo r vehicle.uCAUTION: Do not stare
directly into the beam. Repeat steps for installation on optional
2nd laser accessory kit.
NOTE: Periodic adjustment of the beam may be required.
OPERATION
1. Open the garage door by activating the garage door opener and
drive yo r vehicle into parking space.u
2. The red beam can be seen moving across the hood of your
vehicle as yo drive f rther into the garage (Fig re 4).u u u
3. Stop the vehicle when the beam is positioned at the location you
confirmed in step 3 during SET UP AND ADJUSTMENT.
NOTE: The laser is activated every time you drive into your garage.
The laser will shut off in 1 minute. A residual reflection of the red
beam from the windshield may appear on walls or objects in your
garage. When operating a vehicle, always ensure that there are no
objects on the floor of the garage or in the path of your vehicle. The
parking assist is not a substitute for safe parking practices.
TROUBLESHOOTING
If the laser does not emit a beam:
• Verify nothing is obstr cting the safety sensors.u
• Verify nothing is blocking the parking assist lens.
• Verify that connections are not reversed.
• Verify that all connections are secure.
• Confirm that the parking assist is aimed toward the garage floor.
• Obstruct the path of the safety sensors and look for the red spot
on the garage floor.
Please refer to yo r owner’s man al for additional information onu u
your garage door opener and the safety sensors.
CAUTION
ATTENTION
132C2469-1
LASER RADIATION
DO NOT STARE INTO BEAM
RAYONNEMENT LASER
NE PAS REGARDER DIRECTEMENT
LE RAYONNEMENT LASER
Maximum power output: < 1mW @ 635 - 670nm
Puissance de sortie maximum: < 1mW @ 635 - 670nm
CLASS II LASER PRODUCT
APPAREIL AU LASER DE CLASSE II
This Class B digital apparat s complies with ICES-003.u
Wire Nut Parking AssistScre 6ABX1-1/4"w
Anchor
CARTON INVENTORY
Produkt Specifikationer
| Mærke: | Chamberlain |
| Kategori: | Garage døråbner |
| Model: | CLLP1 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Chamberlain CLLP1 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Garage døråbner Chamberlain Manualer
14 November 2024
13 Marts 2024
12 Januar 2024
13 December 2023
11 December 2023
24 November 2023
21 November 2023
15 November 2023
26 Oktober 2023
2 September 2023
Garage døråbner Manualer
- Garage døråbner Einhell
- Garage døråbner LiftMaster
- Garage døråbner RADEMACHER
- Garage døråbner Craftsman
- Garage døråbner Geba Tronic
- Garage døråbner Hormann
- Garage døråbner Somfy
- Garage døråbner Superrollo
- Garage døråbner Schellenberg
Nyeste Garage døråbner Manualer
12 November 2024
28 September 2024
7 August 2024
18 Maj 2024
25 Marts 2024
14 Februar 2024
28 December 2023
13 Oktober 2023
6 Oktober 2023
1 September 2023