Chicago Pneumatic CP7900 Manual

Chicago Pneumatic savemaskine CP7900

Læs nedenfor 📖 manual på dansk for Chicago Pneumatic CP7900 (12 sider) i kategorien savemaskine. Denne guide var nyttig for 15 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/12

!Avoid direct contact with accessory and work surface during and after

work.

!Cutting edges and saw blades can become hot during use. Do not

touch.

!Never force the tool to cut faster or through heavier gauge material than

rated capacity.

!To prevent damage to the tool and accessory, accessory must be held

firmly against work surface while cutting.

Workplace Hazards

!Slip/Trip/Fall is a major cause of serious injury or death. Be aware of

excess hose left on the walking or work surface.

!High sound levels can cause permanent hearing loss. Use hearing

protection as recommended by your employer or OSHA regulation (see

29 CFR part 1910).

!Maintain a balanced body position and secure footing.

!Repetitive work motions, awkward positions and exposure to vibration

can be harmful to hands and arms. If numbness, tingling, pain or

whitening of the skin occurs, stop using tool and consult a physician.

!Avoid inhaling dust or handling debris from the work process which can

be harmful to your health. Use dust extraction and wear respiratory

protective equipment when working with materials which produce

airborne particles.

!Proceed with care in unfamiliar surroundings. Be aware of potential

hazards created by your work activity.

!Some dust created by power sanding, sawing, grinding, drilling and

other construction activities contains chemicals known to the State of

California to cause cancer and birth defects or other reproductive harm.

Some examples of these chemicals are:

- Lead from lead based paints

- Crystalline silica bricks and cement and other masonry products

- And Arsenic and chromium from chemically-treated rubber

Your risk from these exposures varies, depending on how often you do

this type of work. To reduce your exposure to these chemicals: work in a

well ventilated area, and work with approved safety equipment, such as

dust masks that are specially designed to filter out microscopic particles.

Additional Safety Topics

!This tool and its accessories must not be modified.

!This tool is not intended for use in an explosive atmosphere and is not

insulated for contact with electric power sources.

!Operators and maintenance personnel must be capable of handling the

power of the tool and performing the job task.

!For professional use only

For Additional Safety Information Consult:

!Your employer, union and/or trade association.

!US Department of Labor (OSHA); www.osha.gov; Council of the

European Communities europe.osha.eu.int

!“Safety Code for Portable Air Tools” (ANSI B186.1) available from:

www.ansi.org

!“Safety Requirements for Hand-Held Non-Electric Power Tools”

available from: European Committee for Standardization,

www.cenorm.be

Air Supply and Connection Hazards

!Air under pressure can cause severe injury.

!Always shut off air supply, drain hose of air pressure and disconnect

tool from air supply when not in use, before changing accessories or

when making repairs.

!Never direct air at yourself or anyone else.

!Whipping hoses can cause serious injury. Always check for damaged or

loose hoses and fittings.

!Do not use quick disconnect couplings at tool. See instructions for

correct set-up.

!Whenever universal twist couplings are used, lock pins must be

installed.

!Do not exceed maximum air pressure of 90 psi/6.2 bar or as stated on

tool nameplate.

Projectile Hazards

!Always wear impact-resistant eye and face protection when involved

with or near the operation, repair or maintenance of the tool or changing

accessories on the tool.

!Be sure all others in the area are wearing impact-resistant eye and face

protection.

!Even small projectiles can injure eyes and cause blindness.

Operating Hazards

!Always shut off air supply, relieve hose of air pressure and disconnect

tool from air supply when changing accessories.

!Cutting with these tools will create sharp edges. Wear gloves to protect

hands.

To reduce risk of injury, everyone using, installing,

repairing, maintaining, changing accessories on, or

working near this tool must read and understand

these instructions before performing any such task.

We, Chicago Pneumatic Tool Company, 1800 Overview Drive, Rock Hill, SC 29730 USA,

declare under our sole responsibility that the product to which this declaration relates, is in

conformity with the requirements of the Council Directive of June 1989 on the approximation of

the laws of the Member States relating to machinery (89/392/EEC).

Machine Name CP7900 Reciprocating Saw

Machine Type Power tool utilizes various saw blades for cutting sheet metal and plastic -

No other use is permitted.

Serial No. Tools with No. 02091A or higher

Technical Data

Free Speed 10,000 SPM

Air Pressure 90 psi (6.2 bar)

Harmonized Standards Applied EN292

National Standards Applied ISO 8662-12, Pneurop PN8NTC1.2

Name and Position of Issuer Yves Antier, General Manager, Chicago Pneumatic Tool

Company

Signature of Issuer

Place and Date of Issue Rock Hill, SC 29730 USA, April 1, 2002

Air Supply Requirements

1. Supply tool with 90 psig (6.2 bar) of clean, dry air. Higher pressure drastically

reduces tool life.

2. Connect tool to air line using pipe, hose and fitting sizes shown in the diagram

on page 12.

Lubrication

Use an air line lubricator with SAE #10 oil, adjusted to two drops per minute. If

an air line lubricator cannot be used, add air motor oil to the inlet once a day.

Noise & Vibration Declaration*

Sound pressure level 92.3 dB(A) in accordance with Pneurop PN8NTC1.2. For

sound power, add 10 dB(A).

Vibration value 20.1 m/s , re. ISO 8662-12.

Maintenance

1. Disassemble and inspect parts every three months if the tool is used every

day. Replace damaged or worn parts.

2. High wear parts are underlined in the parts list.

*These declared values were obtained by laboratory type testing in compliance with the stated

standards and are not adequate for use in risk assessments. Values measured in individual work

places may be higher than the declared values. The actual exposure values and risk of harm

experienced by an individual user are unique and depend upon the way the user works, the

workpiece and the workstation design, as well as upon the exposure time and the physical condition

of the user. We, Chicago Pneumatic, cannot be held liable for the consequences of using the

declared values, instead of values reflecting the actual exposure, in an individual risk assessment in

a work place situation over which we have no control.

Model "A"

8940158336 Rev. B

CP7900 Reciprocating Saw

The goal of Chicago Pneumatic is to produce tools that help you work safely and

efficiently. The most important safety device for this or any tool is YOU. Your

care and good judgment are the best protection against injury. All possible

hazards cannot be covered here, but we have tried to highlight some of the

important ones.

Limited Warranty: The "Products" of the Chicago Pneumatic Tool Company ("CP") are warranted to be free from defects in

material and workmanship for one year from the date of purchase. This Warranty applies only to Products purchased new

from CP or its authorized dealers. Of course, this Warranty does not apply to products which have been abused, misused,

modified, or repaired by someone other than CP or its Authorized Service Representatives. If a CP Product proves defective

in material or workmanship within one year after purchase, return it to any CP Factory Service Center or Authorized Service

Center for CP tools, transportation prepaid, enclosing your name and address, adequate proof of date of purchase, and a

short description of the defect. CP will, at its option, repair or replace defective Products free of charge. Repairs or

replacements are warranted as described above for the remainder of the original warranty period. CP's sole liability and your

exclusive remedy under this Warranty is limited to repair or replacement of the defective Product. (There Are No Other

Warranties Expressed Or Implied And CP Shall Not Be Liable For Incidental, Consequential, Or Special Damages, Or

Any Other Damages, Costs Or Expenses Excepting Only The Cost Or Expense Of Repair Or Replacement As

Described Above.)

particular to trademarks, model denominations, part numbers and drawings.

Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by

Warranty or Product Liability.

Produkt Specifikationer

Mærke:	Chicago Pneumatic
Kategori:	savemaskine
Model:	CP7900

Har du brug for hjælp?

Hvis du har brug for hjælp til Chicago Pneumatic CP7900 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

savemaskine Chicago Pneumatic Manualer

Chicago Pneumatic CP7900 Manual

1 September 2024

savemaskine Manualer

Nyeste savemaskine Manualer

Einhell GE-CS 18 Li Manual

15 Oktober 2024

15 Oktober 2024

15 Oktober 2024

14 Oktober 2024

13 Oktober 2024

Einhell TC-AP 650 E Manual

12 Oktober 2024

Einhell TE-SM 36/210 Li Solo Manual

11 Oktober 2024

Einhell BT-SM 2534 Manual

11 Oktober 2024

Hitachi C 7MFA(LA) Manual

9 Oktober 2024

Ozito ECS-406A Manual

6 Oktober 2024