Conair BC171N Manual


Læs nedenfor 📖 manual på dansk for Conair BC171N (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
DOUBLE
CERAMIC
3-IN-1
HOT AIR
BRUSH
For your safety
and continued
enjoymentof this
product, always
ead the instruction
book carefully
before using.
Instructions & Styling Guide
Model BC171N All Versions
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety
precautions should always be taken, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY
FROM WATER
DANGER Any appliance is electrically
live even when the switch is off. To reduce the
risk of death or injury by electric shock:
1. Always unplug appliance immediately
after using.
2. Do not use while bathing or in the shower.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not place in or drop into water or
other liquids.
5. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
WARNING To reduce the risk of
burns, electrocution, fire, or injury to persons:
1. This appliance should never be left
unattended when plugged in. Do not pull,
twist, or wrap line cord around appliance.
2. This appliance should not be used by, on,
or near children or individuals with certain
disabilities. Use could result in fire or
personal injury.
3. Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by the
manufacturer.
4. Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, or if it has been dropped, damaged,
or dropped into water. Return the appliance
to a Conair Service Center for examination
and repair.
5. Keep the cord away from heated surfaces.
Do not pull, twist, or wrap line cord around
appliance, even during storage.
6. Never block the air openings of the appliance
or place it on a soft surface, such as a bed or
couch, where the air openings may be blocked.
Keep the air openings free of lint, hair, and
the like.
7. Never use while sleeping.
8. Never drop or insert any object into any
opening or hose.
9. Do not use outdoors or operate where aerosol
(spray) products are being used or where
oxygen is being administered.
10. Do not use an extension cord to operate hot
air styler.
11. Do not direct hot air toward eyes or other
heat-sensitive areas.
12. Attachments may be hot during use. Allow
them to cool before handling.
13. Do not place appliance on any surface while
in use.
14. While using the appliance, keep your hair
away from the air inlets.
15. Do not operate with a voltage converter.
16. TO AVOID TANGLING, NEVER ROLL THE
HAIR AROUND THE HOT AIR BRUSH MORE
THAT TWO TIMES.
17. This appliance is not a toy. Keep away
from children.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
This appliance is intended for household use
only. Use on Alternating Current (60 hertz) only.
Standard hot air stylers are designed to operate
at 110 to 125 volts AC.
This appliance has a polarized plug (one blade
is wider than the other). As a safety feature, this
plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety
feature.
NOTE: Do not use this styling appliance on
hair extensions.
CHECK ALCI SAFETY FEATURE EVERY TIME
YOU USE APPLIANCE
This appliance is equipped with an Appliance
Leakage Circuit Interrupter (ALCI), a safety
feature that renders it inoperable under some
abnormal conditions, such as immersion in
water. To make sure the ALCI is functioning
properly, perform the following test. The
purpose of this test is to allow you to make sure
the water sensing system (ALCI) is working.
1. Plug in the appliance
and press test button on
plug (see diagram).
2. The appliance will stop
working. There will be an
audible click and reset
button will pop out. This
indicates the ALCI is functioning properly.
3. To reset ALCI with a reset button, unit should
be unplugged. Then push reset button in and
reinsert plug into outlet.
4. If ALCI is not functioning properly, return
appliance to service center.
5. It is important that if immersion occurs, this
unit be brought to a service center. Do not try
to reset.
6. Be sure to repeat test every time you use the
unit to confirm ALCI is operational.
Should the appliance go off and the reset
button pop up during use, this could indicate a
malfunction in the unit. Remove plug from outlet
and allow the appliance to cool. Reinsert plug
into outlet.
The appliance should then function normally.
If not, return it to an authorized Conair Service
Center for evaluation and repair.
Reset
Test
DOUBLE CERAMIC TECHNOLOGY
The barrel of your hot air styler brush
has an Easy-Glide™ double ceramic-coated
surface, the newest technology.
This double ceramic-coated surface helps
to smooth down flyaways. As you wind each
strand around the barrel, it evenly distributes
heat so that the style you create has a salon
perfect, silky smooth, shiny finish. Hair glides
easily over the surface of the barrel. Any residue
from styling products that builds up on the
ceramic-coated barrel can be easily cleaned.
GETTING STARTED
After shampooing your hair, towel-dry and
untangle it carefully with a large-toothed comb.
Always start untangling your wet hair at the
tips, then gradually work your way up. Gentle
untangling prevents split ends from forming.
Now finish drying and styling your hair using
your hot air styler. Make sure your desired
attachment is locked into place. Plug styler into
outlet. Slide switch to turn appliance on and off.
To avoid tangling, never roll the hair around the
hot air brush more than two times. Also, use a
small section of hair at a time.
bc171n_21pa077481_double_ceramic_ib_final.indd 1
bc171n_21pa077481_double_ceramic_ib_final.indd 1
bc171n_21pa077481_double_ceramic_ib_final.indd 1
bc171n_21pa077481_double_ceramic_ib_final.indd 1bc171n_21pa077481_double_ceramic_ib_final.indd 1 2/1/21 11:12 AM
2/1/21 11:12 AM
2/1/21 11:12 AM
2/1/21 11:12 AM2/1/21 11:12 AM
bc171n_21pa077481_double_ceramic_ib_final.indd 2
bc171n_21pa077481_double_ceramic_ib_final.indd 2
bc171n_21pa077481_double_ceramic_ib_final.indd 2
bc171n_21pa077481_double_ceramic_ib_final.indd 2bc171n_21pa077481_double_ceramic_ib_final.indd 2 2/1/21 11:12 AM
2/1/21 11:12 AM
2/1/21 11:12 AM
2/1/21 11:12 AM2/1/21 11:12 AM
FEATURES
1000 watts
High-shine, ionic conditioning
2 heat settings
Professional power cord
1¼ in. brush to curl or straighten
¾ in. nylon & boar bristle brush to curl
Concentrator for silky-straight results
HEAT/SPEED SETTINGS
Low Setting: Ideal airflow for medium,
normal hair.
High Setting: Combines ideal airflow with
higher temperature for thick hair.
GET TO KNOW YOUR STYLER
in. brush
1000 watts
Slide switch with
2 temperature
settings
Cool tip
¾ in. nylon and
boar bristle brush
concentrator
attachment
TO STYLE HAIR
1. After detangling hair, section damp hair into
4 to 8 equal parts, depending on hair type. Use
sectioning clips to section hair for easy styling.
2. Select heat setting based on hair type and
desired effect.
USING THE 1¼ ATTACHMENT
TO CURL AND STRAIGHTEN
Beginning at the crown area, take a section of
hair and place the 1¼ in. brush near the root
area. Slide the hot air brush toward the
ends, then wind toward the root area. Hold for
approximately 10 seconds, then gently unwind
the hair without tension. Continue throughout
the hair until styled as desired.
USING THE ¾ NYLON BRUSH TO CURL
Position the brush under hair, close to the roots.
Slide it down to hair ends. This will give perfect
shape to your hairstyle, while bristles and hot air
create a polished finish and add shine
USING THE CONCENTRATOR FOR VOLUME
Build volume by directing the airflow at roots,
against the natural growth pattern.
This message about...
GROUND
FAULT
CIRCUIT
INTERRUPTERS
...can save a life!
IMPORTANT
Never immerse this product in water
or any other liquids.
IF YOU MUST USE YOUR HOT AIR STYLER IN
THE BATHROOM, INSTALL A GFCI* NOW!
Your local electrician can help you decide
which type is best for you – a portable unit that
plugs into the electrical outlet or a permanent
unit installed by your electrician. The National
Electrical Code now requires GFCIs in the
bathrooms, garages, and outdoor outlets of all
new homes.
WHY DO YOU NEED A GFCI? Electricity and
water don’t mix. If your hot air styler falls in
water while it’s plugged in, the electric shock
can kill you... even if the
switch is off. A regular
fuse or circuit breaker won’t
protect you under these
circumstances. A GFCI offers
you far greater protection.
A GFCI can save your life! Compared to that,
the price is small! Don’t wait... install one
now!
* GFCI is a sensitive device that reacts
immediately to a small electric current leak
by stopping the electricity flow.
CLEANING &
MAINTENANCE
Unplug the appliance and let cool completely
before cleaning it.
Use a damp cloth to clean carefully. Make
sure the appliance is completely dry before
using again.
• The rear filter should be cleaned on a regular
basis using a soft brush to help prevent buildup
and overheating. This will also prolong the
motor life.
USER MAINTENANCE
Your hot air styler is virtually maintenance free.
No lubrication is needed. For proper operating
performance, the hot air styler must be kept
clean. When cleaning is needed, unplug the
cord, allow to cool and clean dust and lint
from air intake openings with a small brush
or the brush attachment of a vacuum cleaner.
The outer surface of the hot air styler should
be wiped clean with a cloth only. Blocked or
clogged air intake vents will cause the hot
air styler to overheat. If overheating occurs,
an automatic safety device will shut the hot
air styler or the heat off to prevent damage or
personal injury. If the unit or the heat turns off,
unplug the cord and allow the hot air styler to
cool for 10 to 15 minutes before restarting.
Make sure the air vents are clean.
CAUTION
NEVER allow the power supply-cord to be pulled,
twisted, or severely bent. Never wrap the cord
tightly around the hot air styler. Damage will
occur at the high flex point of entry into the hot
air styler, causing it to rupture and short circuit.
Inspect the cord frequently for damage. Stop
use immediately if damage is visible or unit
stops or operates intermittently.
If the cord or hot air styler is damaged or does
not operate properly, return it for repair to an
authorized Conair service representative only.
No repairs should be attempted by the
consumer.
STORAGE – IMPORTANT
When not in use, your hot air styler should be
disconnected, allowed to cool and stored in a
safe, dry location, out of reach of children. Do
not wrap line cord around hot air styler. Allow
the cord to hang or lie loose and straight at the
point of entry into the hot air styler.
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water are
a dangerous combination. But did you know
that an electric appliance is still electrically
live even if the switch is off? If the plug is in,
the power is on. So when you are not using
your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED ONE-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the
date of purchase if the appliance is defective
in workmanship or materials. To obtain service
under this warranty, return the defective product
to the service center listed, together with your
purchase receipt. California residents need
only provide proof of purchase and should call
1-800-3-CONAIR for shipping instructions. In
the absence of a purchase receipt, the warranty
period shall be 12 months from the date of
manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE 12-MONTH DURATION OF
THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or
limitation of special, incidental, or consequential
damages, so the above limitation may not apply
to you.
This warranty gives you specific legal rights,
and you may also have other rights, which vary
from state to state.
BEAUTY TIPS:
To achieve the looks you love and
for more great Conair®products,
visit www.conair.com
Service Center
Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
Please register this product at
www.conair.com/registration
For information on any Conair product, call
1-800-3-CONAIR or visit us on the web at
www.conair.com.
©2021 Conair Corporation
21PA077481 IB-17173


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: BC171N

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair BC171N stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024
Conair

Conair CD117NN Manual

2 September 2024
Conair

Conair LLT2 Manual

2 September 2024
Conair

Conair CLS1X Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Gigabyte

Gigabyte ODIN GT 550W Manual

23 November 2024
Stamos

Stamos S-PLASMA 60U Manual

23 November 2024
Velbus

Velbus VMBPIRO-W-20 Manual

23 November 2024
Honor

Honor 90 Pro Manual

23 November 2024
Honor

Honor 80 SE Manual

23 November 2024
Medela

Medela Safe & Dry Manual

22 November 2024
Jane

Jane First Potty Manual

22 November 2024