Conair BC171TR Manual

Conair Ikke kategoriseret BC171TR

Læs nedenfor 📖 manual på dansk for Conair BC171TR (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
2 1 IN
OUBLE
ERAMIC
OT AIR
RUSH
or your safety
nd continued
njoyment of
his product,
ways read
he instruction
ook carefully
efore using.
DAY TO NIGHT COLLECTION
INSTRUCTIONS & STYLING GUIDE
Model BC171T
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety
precautions should always be taken, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY
FROM WATER
DANGER – Any appliance is electrically
live even when the switch is off. To reduce the
risk of death or injury by electric shock:
1. Always unplug appliance immediately
after using.
2. Do not use while bathing or in the shower.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not place in or drop into water or
other liquids.
5. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
WARNING – To reduce the risk of
burns, electrocution, fire, or injury to persons:
1. This appliance should never be left
unattended when plugged in. Do not pull,
twist, or wrap line cord around appliance.
2. This appliance should not be used by, on,
or near children or individuals with certain
disabilities. Use could result in fire or
personal injury.
3. Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by the
manufacturer.
4. Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, or if it has been dropped, damaged,
or dropped into water. Return the appliance
to a Conair Service Center for examination
and repair.
5. Keep the cord away from heated surfaces.
Do not pull, twist, or wrap line cord around
appliance, even during storage.
6. Never block the air openings of the appliance
or place it on a soft surface, such as a bed or
couch, where the air openings may be blocked.
Keep the air openings free of lint, hair, and
the like.
7. Never use while sleeping.
8. Never drop or insert any object into any
opening or hose.
9. Do not use outdoors or operate where aerosol
(spray) products are being used or where
oxygen is being administered.
10. Do not use an extension cord to operate hot
air styler.
11. Do not direct hot air toward eyes or other
heat-sensitive areas.
12. Attachments may be hot during use. Allow
them to cool before handling.
13. Do not place appliance on any surface while
in use.
14. While using the appliance, keep your hair
away from the air inlets.
15. Do not operate with a voltage converter.
16. TO AVOID TANGLING, NEVER ROLL HAIR
AROUND THE HOT AIR BRUSH MORE THAN
TWO TIMES.
17. This appliance is not a toy. Keep away
from children.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
This appliance is intended for household use
only. Use on Alternating Current (60 hertz) only.
Standard hot air stylers are designed to operate
at 110 to 125 volts AC.
This appliance has a polarized plug (one blade
is wider than the other). As a safety feature, this
plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety
feature.
NOTE: Do not use this styling appliance on
hair extensions.
IMPORTANT SAFETY
INSTRUCTIONS
AUTO-MONITORING ALCI SAFETY PLUG
WITH LED INDICATOR
IF THE ALCI LED INDICATOR LIGHT IS
FLASHING CONTINUOUSLY, THIS INDICATES
THAT THE ALCI IS NOT FUNCTIONING
PROPERLY. STOP USING AND RETURN
APPLIANCE TO AN AUTHORIZED
SERVICE CENTER.
CHECK ALCI SAFETY FEATURE EVERY
TIME YOU USE THE APPLIANCE.
LED indicator
(If LED light is flashing, stop using.)
Test
Test
Reset
Reset
This appliance is equipped with an auto-
monitoring Appliance Leakage Circuit Interrupter
(ALCI), a safety feature that provides protection
against electric shock under abnormal
conditions, such as immersion in water. To
ensure that the ALCI is functioning properly,
perform the following test.
1. Plug in the appliance with the power off and
press the test button on the ALCI (see diagram).
2. There will be an audible click, the reset button
will pop out, and the LED indicator will be off.
The appliance will not turn on. This indicates the
ALCI is functioning properly.
3. To reset the ALCI, the unit should be
unplugged. Then press the reset button and
plug the unit back into the outlet. The appliance
should work normally when switched on.
4. Be sure to repeat this test each time you
use the unit to confirm that the ALCI is
operating properly.
5. If the appliance shuts off and the reset
button pops up during use, this could indicate
a malfunction. Remove the plug from the outlet
and allow the appliance to cool. Press the reset
button and plug appliance into the outlet. The
appliance should function normally. If not, send
it to an authorized service center for evaluation.
6. IF THE UNIT HAS BEEN IMMERSED IN
WATER, DO NOT ATTEMPT TO RESET AND USE
THE APPLIANCE. IT SHOULD BE SENT TO AN
AUTHORIZED SERVICE CENTER IMMEDIATELY.
DOUBLE CERAMIC TECHNOLOGY
The barrel of your 1¼ in. hot air styler brush
has an Easy-Glide™ double ceramic-coated
surface, the newest technology.
This double ceramic-coated surface helps
to smooth down flyaways. As you wind each
strand around the barrel, it evenly distributes
heat so that the style you create has a salon
perfect, silky smooth, shiny finish. Hair glides
easily over the surface of the barrel. Any residue
from styling products that builds up on the
ceramic-coated barrel can be easily cleaned.
GETTING STARTED
After shampooing your hair, towel-dry and use
the dryer handle without the attachment to
remove excess moisture from hair. Use a large-
toothed comb to carefully untangle hair. Always
start untangling your wet hair at the tips, then
gradually work your way up to the scalp. Gentle
untangling prevents split ends from forming.
You may now finish drying and styling your hair
using your hot air styler. Make sure your desired
attachment is locked into place. Plug styler
into outlet. Slide switch to turn appliance on
and off.
To avoid tangling, never roll the hair around the
hot air brush more than two times. Also, use a
small section of hair at a time.
FEATURES
• 1000 watts
• High-shine, ionic conditioning
• 2 heat settings
• Professional power cord
DRYER HANDLE
Use handle without attachment to remove
excess moisture from hair before styling.
1¼ IN. THERMAL BRUSH
To curl and straighten.
HEAT/SPEED SETTINGS
Low Setting: Ideal airflow for medium,
normal hair.
High Setting: Combines ideal airflow with
higher temperature for thick hair.
GET TO KNOW YOUR STYLER
1¼ in. brush
1000 watts
ON/OFF slide
switch with
2 temperature
settings
Cool tip
TO STYLE HAIR
1. After detangling hair, section damp hair into
4 to 8 equal parts, depending on hair type. Use
sectioning clips to section hair for easy styling.
2. Select heat setting based on hair type and
desired effect.
3. With the brush attachment in place, begin at
the crown area. Then take a section of hair and
place the brush near the root area.
4. Slide the hot air brush toward the ends,
then wind toward the root area. Hold for
approximately 10 seconds, then gently
unwind the hair without tension. Continue with
remaining sections of hair until styled
as desired.
5. Finish look with favorite styling spray.
TEMPERATURE SETTING HAIR TYPE
LOW Fine to
Medium Hair
HIGH Thick Hair
This message about...
GROUND
FAULT
CIRCUIT
INTERRUPTERS
...can save a life!
IMPORTANT
Never immerse this product in water
or any other liquids.
IF YOU MUST USE YOUR HOT AIR STYLER IN
THE BATHROOM, INSTALL A GFCI* NOW!
Your local electrician can help you decide
which type is best for you – a portable unit that
plugs into the electrical outlet or a permanent
unit installed by your electrician. The National
Electrical Code now requires GFCIs in the
bathrooms, garages, and outdoor outlets of all
new homes.
WHY DO YOU NEED A GFCI? Electricity and
water don’t mix. If your hot air styler falls
in water while it’s plugged in, the electric
shock can kill you...even if
the switch is off. A regular
fuse or circuit breaker won’t
protect you under these
circumstances. A GFCI offers
you far greater protection.
A GFCI can save your life! Compared to that,
the price is small! Don’t wait...install one
now!
* GFCI is a sensitive device that reacts
immediately to a small electric current leak
by stopping the electricity flow.
CLEANING &
MAINTENANCE
• Unplug the appliance and let cool completely
before cleaning it.
• Use a damp cloth to clean carefully. Make
sure the appliance is completely dry before
using again.
• The rear filter should be cleaned on a regular
basis using a soft brush to help prevent buildup
and overheating. This will also prolong the
motor life.
USER MAINTENANCE
Your hot air styler is virtually maintenance free.
No lubrication is needed. For proper operating
performance, the hot air styler must be kept
clean. When cleaning is needed, unplug the
cord, allow to cool, and clean dust and lint from
air intake openings with a small brush or the
brush attachment of a vacuum cleaner. The
outer surface of the hot air styler should be
wiped clean with a cloth only.
Blocked or clogged air intake vents will
cause the hot air styler to overheat. If
overheating occurs, an automatic safety device
will shut the hot air styler or the heat off to
prevent damage or personal injury. If the unit or
the heat turns off, unplug the cord and allow the
hot air styler to cool for 10 to 15 minutes before
restarting. Make sure the air vents are clean.
CAUTION
NEVER allow the power-supply cord to be pulled,
twisted, or severely bent. Never wrap the cord
tightly around the hot air styler. Damage will
occur at the high flex point of entry into the hot
air styler, causing it to rupture and short circuit.
Inspect the cord frequently for damage. Stop
use immediately if damage is visible or unit
stops or operates intermittently.
If the cord or hot air styler is damaged or does
not operate properly, return it for repair to an
authorized Conair service representative only.
No repairs should be attempted by the
consumer.
STORAGE – IMPORTANT
When not in use, your hot air styler should be
disconnected, allowed to cool, and stored in a
safe, dry location, out of reach of children. Do
not wrap line cord around hot air styler. Allow
the cord to hang or lie loose and straight at the
point of entry into the hot air styler.
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water are
a dangerous combination. But did you know
that an electric appliance is still electrically
live even if the switch is off? If the plug is in,
the power is on. So when you are not using
your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED ONE-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the
date of purchase if the appliance is defective
in workmanship or materials. To obtain service
under this warranty, return the defective product
to the service center listed, together with your
purchase receipt. California residents need
only provide proof of purchase and should call
1-800-3-CONAIR for shipping instructions. In
the absence of a purchase receipt, the warranty
period shall be 12 months from the date of
manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE 12-MONTH DURATION OF
THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or
limitation of special, incidental, or consequential
damages, so the above limitation may not apply
to you.
This warranty gives you specific legal rights,
and you may also have other rights, which vary
from state to state.
BEAUTY TIPS:
To achieve the looks you love and
for more great Conair®products,
visit www.conair.com
Service Center
Conair LLC
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
Please register this product at
register.conair.com
For information on any Conair
® product, call
1-800-3-CONAIR or visit us on the web at
www.conair.com.
©2022 Conair LLC
22PA083560 IB-17717

Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: BC171TR

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair BC171TR stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair True Glow PB8NPRF Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MiniPRO CS80N Manual

1 Oktober 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024
Conair

Conair InfinitiPRO 998 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024
Lucide

Lucide Casper i 79166/19/12 Manual

23 December 2024
Lucide

Lucide Merlina 78193/30/66 Manual

23 December 2024
Lucide

Lucide Pippa 77583/81/30 Manual

23 December 2024
Lucide

Lucide Pia 45380/04/30 Manual

23 December 2024
Lucide

Lucide Pia 45280/01/30 Manual

23 December 2024
Lucide

Lucide Anaka 45179/03/30 Manual

23 December 2024
Lucide

Lucide Zych 45156/01/97 Manual

23 December 2024