Conair CD2112 Manual


Læs nedenfor 📖 manual på dansk for Conair CD2112 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
SET AND PROTECT
COOL AIR STYLER
model CD2112 – all versions
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety
precautions should always be taken, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER – Any appliance is electrically
live even when the switch is off. To reduce the
risk of death by electric shock:
1. Always unplug appliance immediately
after using.
2. Do not use while bathing or in the shower.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not place in, or drop into water or other
liquids.
5. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
WARNING – To reduce the risk of
burns, electrocution, fire, or injury to persons:
1. This appliance should never be left
unattended when plugged in.
2. Do not pull, twist, or wrap line cord
around appliance.
3. This appliance should not be used by, on
or near children or individuals with certain
disabilities.
4. Use this appliance only for its intended use,
as described in this manual. Do not use
attachments not recommended by the
manufacturer.
5. Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly or if it has been dropped or
damaged, or dropped into water. Return the
appliance to an Authorized Service Center for
examination and repair.
6. Keep the cord away from heated surfaces.
7. Never use while sleeping.
8. Never drop or insert any object into any
opening or hose.
9. Do not use outdoors or operate where aerosol
(spray) products are being used or where
oxygen is being administered.
10. Unit is hot when in use. Do not let heated
surface touch eyes or skin.
11. Do not place the heated unit directly on
any surface while it is hot or plugged in.
12. Never block the air openings of the
appliance or place it on a soft surface, such as
a bed or couch, where the air openings may be
blocked. Keep the air openings free of hair, lint
and other debris.
13. Do not use an extension cord with this
appliance.
14. Do not touch hot surfaces of the appliance.
Use handles or knobs.
15. Do not attempt to touch the housing of
your appliance near the plates, as it is hot
when in use.
16. This appliance is not a toy. Keep away
from children.
17. Do not use with a voltage converter.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
This styler is intended for household use. Use on
Alternating Current (60 hertz) only. This unit is
designed to be operated at 120V AC.
This appliance has a polarized plug (one blade is
wider than the other). As a safety feature, this
plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety
feature.
NOTE: Do not use this styling appliance on
hair extensions.
AUTO-MONITORING FUNCTION
ALCI WITH LED INDICATOR
CHECK ALCI SAFETY FEATURE EVERY TIME
YOU USE APPLIANCE. WHEN THE LED LIGHT
IS FLASHING, THIS INDICATES THE ALCI IS
NOT FUNCTIONING PROPERLY. IF THIS IS THE
CASE, STOP USING AND RETURN APPLIANCE
TO SERVICE CENTER.
This appliance is equipped with an auto-
monitoring function Appliance Leakage Circuit
Interrupter (ALCI), a safety feature that renders
it inoperable under some abnormal conditions,
such as immersion in water. To make sure
the ALCI is functioning properly, perform the
following test. The purpose of this test is to
allow you to make sure the water sensing
system (ALCI) is working.
1. Plug in the
appliance and press
test button on plug
(see diagram).
2. The appliance will
stop working. There
will be an audible
click, reset button will
pop out and the LED light is off. This indicates
the ALCI is functioning properly.
3. To reset ALCI with a reset button (see
diagram), unit should be unplugged. Then push
reset button in and reinsert plug into outlet.
4. If ALCI is not functioning properly and
LED light is flashing, stop using immediately
and return appliance to service center. If the
appliance stops working and the LED light on
the ALCI is flashing, return appliance to service
center.
5. It is important that if immersion occurs, this
unit be brought to a service center. Do not try
to reset.
6. Be sure to repeat test every time you use the
unit to confirm ALCI is operational.
Should the appliance go off and the reset
button pop up during use, this could indicate a
malfunction in the unit. Remove plug from outlet
and allow the appliance to cool. Reinsert plug
into outlet. The appliance should then function
normally. If not, return it to an authorized Conair
Service Center for evaluation and repair.
Conair’s professional salon standards of
engineering provide you with a uniform and
improved heat recovery system that maintains
the iron at constant temperatures. There is a
constant supply of power to ensure that heat is
continuously and quickly delivered for optimal
styling results, unlike other units, which lose
heat during use. This provides consistent styling
power so that every strand of your hair is set
with the same level of heat and comes out the
same way for a perfect finish.
Never leave your styler on and unattended.
However, should you fail to turn the iron off,
it will shut itself off automatically within
60 minutes.
STYLING WITH THE
QUARTZ CERAMIC-COATED,
EASY-GLIDE PLATES & BARREL
Your new styler has a quartz ceramic-coated,
easy-glide surface. This means its not only
simpler to clean off styling product residue, etc.,
after each use, but you’ll find that hair glides
easily over the surface of the plates as you’re
styling. The ceramic surface also helps smooth
down flyaways. It evenly distributes heat so that
the style you create has a salon-perfect, silky
smooth, shiny finish.
UNIQUE AIRFLOW SYSTEM
This styling iron features a unique cooling
system for the outer barrel. A fan releases cool
air along the outside of the barrel to help set
your style and creates long-lasting curls.
USING INSTANT HEAT, THE 3
HEAT SETTINGS & UNIFORM
HEAT RECOVERY SYSTEM
This styling iron features a heater that
maintains constant temperature during use
for precision styling.
The Instant Heat technology has 3 heat settings.
There is a temperature range thats gentle and
safe for every type of hair, from the finest to the
most resistant, and helps you create the look
you want.
If you have fine hair, a low temperature will
provide the best results. If you have thick, wavy
or hard-to-style hair, keep the heat setting on
high. Always test a small section of hair to
ensure the proper heat setting for your hair.
You can vary the iron’s temperature according
to your particular need!
TEMPERATURE SETTING GUIDE
HAIR TYPE TEMP. CONTROL
FRAGILE/FINE HAIR Low(L) − 320ºF
MEDIUM/ Medium(M) − 356ºF
NORMAL HAIR
WAVY/CURLY HAIR/ High(H) − 400ºF
COARSE/THICK HAIR
Stays cool with air
OUTER BARREL flow system on
GET TO KNOW
Temperat
Setting In
LED
Quartz
Ceramic-
Coated Pl
Heat Up to
400°F
ON
Bu
el
l
w
/Close
n
N/OFF
ation LED
GETTING STARTED
Plug the styler into any standard electrical
outlet. The RED temperature setting and GREEN
fan LED light up immediately. The lights blink
and cycle through 3 times and then turn off.
Press and hold ON/OFF button for 1–2 seconds
to turn the styler on. The unit will automatically
default to the MEDIUM heat setting. The
LOW and MEDIUM settings turn to a red LED.
The LOW red LED will remain solid, while the
MEDIUM red LED blinks. It will stop blinking
and become solid when desired temperature is
reached. The GREEN fan LED blinks and then
becomes solid. The fan starts to release cool air
and will become a solid GREEN when the correct
heat setting has been reached.
Press the ON/OFF button again to select your
desired temperature setting. Press the ON/OFF
button 2 times quickly to turn off fan. The GREEN
LED will blink. Press the ON/OFF button 2 times
quickly again to turn on the fan. The GREEN
LED becomes solid. Press and hold the ON/OFF
button for 1–2 seconds to turn the unit off. The
RED LED light will turn off immediately. The fan
and GREEN LED will remain for a few seconds
and then turn off. Unplug the unit. Allow the
styler to cool down before storing.
WARNING: The styler will get very hot within
a few seconds and should not be placed in
contact with the skin after the unit has
been turned on.
SWITCH FUNCTION FOR
TEMPERATURE SETTING
L M H
To select your temperature, press the ON/OFF
button again. Press and release button until you
reach the temperature you desire. As the
temperature increases to the next setting, the
LED lights will blink as follows:
Temperature setting is set to LOW. The LOW
red LED light blinks, then turns solid when the
temperature has been reached.
Temperature setting is set to MEDIUM. The LOW
red LED remains solid. MEDIUM red LED light
blinks, then turns solid when the temperature
has been reached.
• •
Temperature setting is set to
HIGH. The LOW
and MEDIUM red LED remain solid. HIGH setting
light blinks, then turns solid when the tempera-
ture has been reached.
TO CURL HAIR
Hair should be clean and completely dry before
using the styler. Ensure hair is dry and combed
through.
1. Separate a section of hair. The smaller the
section, the more defined the curl. The larger the
section, the looser the curl or wave.
2. Press and hold the Open/
Close button to open plates.
Take a section of hair and
place it between the plates,
roughly 2 inches from the
roots. (See Fig. 1.) Release
the plates by letting go
of the Open/Close button.
3. Turn the styler 180° back
on itself, so that the hair is
wrapped once around the
outside of the styler (Fig. 2).
Cool tips provide a safe,
heat-resistant place to hold
the styler while you curl.
4. Slowly glide the styler
along the length of hair
from roots to ends in a
downward motion (Fig. 3).
5. Release the hair from the
styler. The cool air channels set the style.
6. Repeat for each section of hair.
(F ig. 1)
(F ig. 2)
(F ig. 3)
This message about...
GROUND
FAULT
CIRCUIT
INTERRUPTERS
...can save a life!
IF YOU MUST USE YOUR STYLER IN THE
BATHROOM, INSTALL A GFCI* NOW!
Your local electrician can help you decide
which type is best for you – a portable unit that
plugs into the electrical outlet or a permanent
unit installed by your electrician. The National
Electrical Code now requires GFCIs in the
bathrooms, garages, and outdoor outlets of all
new homes.
WHY DO YOU NEED A GFCI?
Electricity and water don’t mix.
If your styler falls into water while
its plugged in, the electric shock
can kill you...even if the switch
is off. A regular fuse or circuit breaker won’t
protect you under these circumstances.
A GFCI offers you far greater protection.
A GFCI can save your life! Compared to
that, the price is small! Don’t wait...install
one now!
* A GFCI is a sensitive device that reacts
immediately to a small electric current leak
by stopping the electricity ow.
FEDERAL COMMUNICATIONS
COMMISSION NOTICE
WARNING: Changes or modifications to this
unit not expressly approved by the party
responsible for compliance could void the
users authority to operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) This device must
accept any interference received, including
interference that may cause undesired
operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
SUPPLIER’S DECLARATION
OF CONFORMITY
Brand: InfinitiPRO by Conair
Model No.: CD2112
Description: Cool Air Curler
Responsible Party: Conair Corporation,
1 Cummings Point Road,
Stamford, CT 06902 (203) 351-9000
Standards: FCC Part 15 Subpart B,
ANSI C63.4-2014
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and (2) This device must accept
any interference received, including interference
that may cause undesirable operation.
DATE OF ISSUE: 06/09/2021
USER MAINTENANCE
Your styling iron is virtually maintenance free.
No lubrication is needed. Keep all vents and
openings clear of dirt and dust. If cleaning
becomes necessary, disconnect the unit from
the power source, allow to cool and wipe
exterior with a cloth. If any abnormal condition
occurs, unplug the unit, allow it to cool, and
return it for repair to an Authorized Service
Center only. No repairs should be attempted by
the consumer.
CAUTION
NEVER allow the power supply cord to be pulled,
twisted, or severely bent. Never wrap the cord
tightly around the appliance. Damage will occur
at the high flex point of entry into the appliance,
causing it to rupture and short circuit. Inspect
the cord frequently for damage. Stop use
immediately if damage is visible or if unit stops
or operates intermittently.
STORAGE
When not in use, your appliance is easy to store.
Allow appliance to cool, then simply store out of
reach of children in a safe, dry location. Do not
jerk or strain cord at plug connections. Do not
wrap the line cord around the appliance. Allow
the cord to hang or lie loose and straight at the
point of entry into the appliance.
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water are
a dangerous combination. But did you know
that an electric appliance is still electrically
live even if the switch is off? If the plug is in,
the power is on. So when you are not using
your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED ONE-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the date
of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return the
defective product to the service center listed,
together with your purchase receipt. California
residents need only provide proof of purchase
and should call 1-800-3-CONAIR for shipping
instructions. In the absence of a purchase
receipt, the warranty period shall be 12 months
from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE 12-MONTH DURATION OF
THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH
OF THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER. Some states do
not allow the exclusion or limitation of special,
incidental, or consequential damages, so the
above limitation may not apply to you.
This warranty gives you specific legal rights,
and you may also have other rights, which vary
from state to state.
BEAUTY TIPS
To achieve the looks you love and
for more great InfinitiPRO by Conair®
products, visit infiniti.conair.com
Please register this product at
www.conair.com/registration
For info on any Conair or InfinitiPRO by Conair
product, call or visit us 1-800-3-CONAIR
on the web at www.conair.com/infiniti
Service Center
Conair LLC
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
©2021 Conair LLC
21PA078773 IB-17294A


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: CD2112

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair CD2112 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024