Conair Close Cut Precision HC6500 Manual

Conair Ikke kategoriseret Close Cut Precision HC6500

Læs nedenfor 📖 manual på dansk for Conair Close Cut Precision HC6500 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

CLOSE CUT PRECISION

P R O F E S S I O N A L , H I G H - P E R F O R M A N C E

L I T H I U M I O N M E T A L C L I P P E R & T R I M M E R

Instruction Booklet

For your safety and continued enjoyment

of this product, always read the instruction

booklet carefully before using.

Respect the Ritual®

stock.image

Please register this product at

Service Center

Conair LLC

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

22PG085418

IB-17816

Model HC6500

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, take basic safety

precautions, including the following:

READ ALL INSTRUCTIONS

BEFORE USING

KEEP AWAY

FROM WATER

FOR HOUSEHOLD

USE ONLY

DANGER – Any appliance is

electrically live, even when the switch is off.

To reduce the risk of death or injury by

electric shock:

1. Unplug this appliance before cleaning.

2. Do not place or store appliance where it

can fall or be pulled into a tub or sink.

3. Do not use while bathing or in the shower.

4. Do not place in, or drop into, water or

other liquids.

5. Do not reach for an appliance that has

fallen into water. Unplug immediately.

For dry location use only. Do not expose to

liquids, vapor or rain.

6. Except when charging, always unplug this

appliance from electrical outlet immediately

after using.

WARNING – To reduce the

risk of burns, electric shock, fire, or injury

to persons:

1. Except when charging, this appliance

should never be left unattended when

plugged in.

2. This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning the use of the

appliance by a person responsible for

their safety. Children should be supervised

to ensure that they do not play with the

appliance.

3. Use this appliance only for its intended

purpose as described in this manual. Do not

use attachments not recommended by the

manufacturer. Do not use an extension cord

to operate this appliance.

4. Never operate this appliance if it has a

damaged cord or plug, if it is not working

properly or if it has been dropped,

damaged or dropped into water. Return the

appliance to a service center for examination

and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any

opening on this appliance.

7. Keep air openings free of lint, hair and

similar objects.

8. Do not use this appliance with a damaged

or broken comb or with teeth missing from

the blades, as injury may occur. Before use,

make certain blades are aligned properly.

9. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

10. Never operate the appliance with the air

openings blocked or while on a soft surface,

such as a bed or couch, where the air

openings may be blocked.

11. Always attach plug to appliance first, then

to outlet. To disconnect, turn all controls to

OFF, then remove plug from outlet.

12. Avoid skin coming into contact with

moving blade.

13. Do not short the polarity (output cord) –

ensure jack is plugged into the unit before

plugging the adapter into outlet.

14. Use only with a certified USB power

source, such as a computer, receptacle, lamp,

class 2 power supply or automotive adapter.

15. This appliance is not a toy. Keep away

from children.

FEDERAL COMMUNICATIONS

COMMISSION NOTICE

WARNING: Changes or

modifications to this unit not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

SUPPLIER’S DECLARATION

OF CONFORMITY

Brand: CONAIRMAN®

Model No.: HC6500

Description: Clipper

Responsible Party: Conair LLC,

1 Cummings Point Road,

Stamford, CT 06902 (203) 351-9000

Standards: FCC Part 15 Subpart B,

ANSI C63.4-2014

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) This device may not cause

harmful interference, and (2) This device must

accept any interference received, including

interference that may cause undesirable

operation.

DATE OF ISSUE: October 10, 2022

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

USER MANUAL

Before using the Class 2 Power Supply, read

these instructions carefully.

Use with adapter: CA74

Rated input voltage:

100–240V AC, 50/60Hz 0.3A

Rated output: 5.0V DC, 1000mA

OPERATION

1. For dry location use only. Do not expose

to water.

2. When not in use, unplug unit completely.

3. Unit will become warm during operation.

CAUTION

1. Ensure jack is plugged into the clipper unit

before plugging the adapter into the outlet.

2. Do not operate any appliance that has a

damaged output cord or housing.

3. Always unplug the unit before cleaning or

when not in use, except when charging.

4. This power unit is intended to be correctly

oriented in a vertical or floor-mount

position.

5. Be sure voltage is correct before plugging

in. The adapter included automatically

adjusts to the input voltage. For connection

to a power supply not in the U.S.A., use an

attachment plug adapter of the proper

configuration for power outlet. DO NOT USE

WITH A VOLTAGE CONVERTER.

FEATURES

• Cordless clipper – use cordless for total

flexibility and control.

• Lithium-ion technology with powerful DC

motor for powerful cutting action and

sustained power performance.

• Precision-engineered high-grade hardened

steel blades with unique super-sharp

cutting angle for smooth, effortless cutting.

• Taper control for custom settings.

• 3-hour full charge for approximately 3

hours of use.

Your new CONAIRMAN® haircut kit has

everything you need to achieve professional

haircuts at home. It features a high-perfor-

mance metal series clipper with adjustable

taper control. The clipper is engineered with

Japanese stainless steel blades. Japanese

stainless steel is considered one of the best

brands and is renowned for its strength and

the ability to hold the sharpest edge. Also

included are 8 comb attachments for different

hair lengths, barber scissors, a storage pouch,

cleaning brush, lubricating oil and a blade

guard.

INSTRUCTIONS

FOR USE

CHARGING THE APPLIANCE

IMPORTANT

To charge the clipper, first ensure the clipper

is switched off, plug the USB cable into the

USB port on the USB adapter with output 5.0V

DC, 1000mA, then insert the Micro USB plug

into the bottom of the clipper. Plug the adapter

into wall outlet (at the voltage listed on the

label affixed to the adapter). Unplug adapter

when not in use.

This clipper is easy to use, but before first

use, you must charge the unit for 3 hours.

Maximum battery capacity will be reached

only after 3 charging/discharging cycles. A

full charge will provide approximately 2 hours

use. When the clipper is about to run out of

power, the charging indicator will flash and

you will have approximately 10 minutes of

use remaining. The charging LED indicator

light will flash when correctly connected to

the main power and will continuously flash

until the battery has fully charged. When the

battery is fully charged, the LED indicator light

will stop flashing but remain on.

WARNING: When charging, the unit can’t

operate. If the charging light suddenly starts to

flash rapidly, the appliance is faulty. If this

happens, stop charging, remove the adapter

from the outlet and contact our Customer Care

Center for further advice (see the Warranty

section of this information booklet).

OILING INSTRUCTIONS

IMPORTANT! It is highly recommended

before each use to oil the blades with the oil

provided. This ensures optimum cutting

performance. Unscrew the cap and cut off the

very end of the plastic tube with a pair of

scissors to release the oil.

To oil the blades, ensure that the unit is

switched on. Gently squeeze the oil tube and

apply 2 drops of oil to the blades (see FIGS. 1,

2, and 3). Leave the unit on for a few seconds

to allow the oil to thoroughly spread the

length of the blades. Switch off the unit and

remove any excess oil by gently dabbing with

a cloth.

Be careful not to use too much oil and don’t

oil your clipper more than necessary, as this

could damage the motor. (Never attempt to oil

the motor bearing, as it is permanently

lubricated.)

KEEP OIL OUT OF REACH OF CHILDREN.

OIL BOTH AREAS

FIG. 1

OIL BOTH AREAS

FIG. 2

FIG. 3

PRESERVING THE BATTERY

In order to maintain the optimum capacity of

the rechargeable battery, the appliance has to

be fully discharged approximately every 6

months. Then recharge the device for 3 hours

to full capacity again.

THE CONAIR GUIDE TO CUTTING

HAIR AT HOME

Before you start:

1. Inspect your clipper. Make sure it’s free of

hair and dirt, properly oiled and running

smoothly.

2. Place a barber cape or a towel around the

neck of the person whose hair is to be cut.

3. Seat the person so that his or her head is

at your eye level. This gives you greater

visibility and control.

4. Comb hair until it’s tangle free. Then hold

clipper in a comfortable grip. Now you’re

ready to cut.

MEDIUM-TO-LONG CUT

To begin, cut only a small amount of hair until

you become used to the length each

attachment leaves the hair. Try the longest

attachment on the clipper ﬁrst. If you want a

shorter cut, you can then use shorter combs.

• Short attachment comb (number 0) cuts

hair to 1/32" (0.8mm).

• Short attachment comb (number 0.5) cuts

hair to 1/16" (1.5mm).

• Medium attachment comb (number 1) cuts

hair to 1/8" (3mm).

• Medium attachment comb (number 2) cuts

hair to 1/4" (6mm).

• Medium attachment comb (number 3) cuts

hair to 3/8" (9.5mm).

• Long attachment comb (number 4) cuts hair

to 1/2" (13mm).

• Long attachment comb (number 5) cuts hair

to 5/8" (16mm).

• Long attachment comb (number 6) cuts hair

to 3/4" (19mm).

Attach comb by

holding it teeth up,

then snapping onto

the bottom of the

clipper blade.

To remove comb

attachment, place

index finger and

thumb as illustrated;

then pull out and up.

NOTE: Never push or shove the clipper

through the hair to make it move more

quickly. Professional experience shows

that the clipper works most efficiently

when it cuts through the hair at its own

speed.

To begin cutting hair:

1. The hair should be combed

in its natural direction.

2. Using the longest comb

attachment, trim sides from

the bottom upward. Hold

clipper lightly against the hair with teeth of

the comb attachment pointing up ward yet flat

against the head.

Gradually lift the clipper

upward and outward

through the hair, trim-

ming just a little at a

time.

Repeat around sides and

back of head.

If you want hair to be

even shorter:

A) Apply more pressure

to the head with the

comb attachment that

is in place. This takes a

little practice, of course.

OR B) Switch to a shorter

comb attachment.

Remember, it’s better to

leave too much hair than

too little.

For longer hair on top, use

the barber comb and lift

hair on the top of the head,

cutting over the comb.

Or hold the hair between

the fingers and cut to desired length. Always

working from the front to the back of the

head, gradually cut the hair shorter by reduc-

ing the space between the comb or fingers

and the head. Comb often to check for uneven

strands and to get rid of trimmed hair.

OUTLINING

Outlining requires no

attachments. Comb hair into

the desired style. Position

the clipper between the

sideburns and the ear (see

illustration), making sure the

corner edge of the blade is

against the hairline. With the

outline of the hair as your

guide, slowly move the clip-

per over, around and behind

the ears. For the back of the

neck and the sideburns, hold the clipper in

the opposite direction and, holding it against

the skin at the length desired, move the clip-

per downward.

STOP. COMB. CHECK.

For best results, do as the professionals do:

Comb hair often and check clipping results as

you comb. This way you avoid uneven sides,

bangs, neckline, etc.

SHORT CUTS TO PERFECT

FLATTOPS, CREW CUTS, ETC.

Always cut from the back of the neck to

the crown, using the longest comb setting.

Hold the comb attachment flat against the

head and slowly move the clipper up through

the hair. Use the same technique for the

sides, cutting from the bottom

to the upper side of the head.

For the front to the crown, cut

the hair against the direction

in which it grows. Then even it

up with the sides.

For a flattop, use the

flat comb, not the comb

attachment. Cut hair on top

of the head over flat comb

(see illustration).

FADE OR TAPER

Fades and tapers can vary

according to ethnic and regional preferences.

Except among the most highly trained profes-

sionals, the two terms are often used inter-

changeably. The techniques to create them

are quite similar.

The Fade: A fade is a transition in hair length

from thin to full that appears around the sides

and back of the head. You can have a low, mid

or high fade, depending on your preference.

Start by choosing your fade line. This is the

point where the fade begins, where the hair

is shortest. Be conservative to start. Choosing

a #1 attachment comb will trim very close to

the skin, whereas using no attachment comb

will leave the skin bald. Therefore, we suggest

starting with a #3 or #4 for your first attempt.

You can always go shorter later, but you’ll have

to wait for weeks for hair to grow back if you

cut it too short at the start.

The Taper: A taper (or tape-up) is like a fade,

but it sits lower on the head, closer to the

ears and low on the nape of the neck (see

image A on right). It is usually done on the

temple and sideburn areas, proceeding low

above the ear, and around to the back of the

head, but it can continue around the perim-

eter of the head if so desired (see image B).

Choose longer guide combs for a taper than

you would for a fade—a #4 or #5 is a good

start.

If you are unsure, go with a #6 and use a

C-scoop or crescent-shape motion. The taper

is considered a more conservative look, for

men in the corporate workplace. It is layered

much like a fade, and the technique to create

it is much the same with minor differences.

Low, Mid or High Fade: Where you stop

fading is up to you. You can create a low,

mid or high fade. The low fade (see image

B), which is essentially the same as a taper

and the most conservative style, stops at

the temple, continues just above the ear

and proceeds to the back across the lower

occipital bone below the parietal ridge. It will

usually stay within an inch or 2 of the lower

neckline. A mid fade (see image C) can stop

at the temple or go a little higher. It proceeds

higher above the ear and aims for the parietal

ridge, approximately 2 to 3 inches above the

low hairline. A high fade (see image D) lands

above the temple and dips slightly as it pro-

ceeds to the back of the head, above the pari-

etal ridge. You can go even higher if you want

to create that high and tight U.S. Marine look.

These specifications are general guidelines.

You can create a fade or taper anywhere on

the head and use any degree of steepness

you desire. Cutting hair is an art form! The

key is to get the look you want.

Technique: Start at the bottom of the hairline

and use short, upward strokes, trimming as

evenly as possible across the back hairline

and around to each side, over the ears and

sideburns. The length of the stroke will deter-

mine how steep or gradual the fade will be,

depending on the look you want. Just keep

your strokes proportional.

Start with quarter-inch to half-inch strokes,

using a gentle scrubbing motion, working

square to the head surface at this point.

Then, switch to the next-longer guide comb

and trim around the hairline again, blending

in with your first trim layer. To achieve bet-

ter blending with the first layer, keep using a

C-scoop motion with the clipper, gently bend-

ing the wrist to pull the clipper away from the

head as you move upward.

USER MAINTENANCE

INSTRUCTIONS

CARE OF YOUR CLIPPER

IF YOU DETERMINE THAT BLADE

ALIGNMENT IS INCORRECT:

CONAIRMAN® hair clippers are carefully

inspected to ensure that the blades are in

perfect alignment. Of course, you will need to

realign the blades after removal for cleaning

or replacement, or if they should be knocked

out of alignment. How can you tell if blades

need realigning? Simply match them up, point

for point, to conform with FIG. 1 below:

FIG. 1

Bottom Blade

Top Blade

1/32" to 1/16"

To prevent the clipper from contacting the

skin or cutting too closely, make certain that

the end top blade teeth are 1/32" to 1/16"

back from bottom blade.

To Align Blades:

1. Unplug clipper and slightly

loosen screws (see FIG. 2).

2. Position the extreme left-

hand tooth of the top blade so

that it either covers or appears

on the left of the first small

tooth on the bottom blade.

FIG. 2

3. Make sure that the big tooth on the bottom

blade touches the extreme right-hand tooth

of the top blade.

Any other servicing should be performed by

an authorized service representative. This

appliance has no user-serviceable parts.

This appliance is for household use.

ADJUSTABLE TAPER LEVER

Just like on professional clippers, the

CONAIRMAN® taper lever is positioned at your

thumb. You can hold the clipper in your hand

and adjust the lever at the same time...while

you’re clipping.

This taper lever eliminates the need in some

situations for a comb attachment because it

lets you gradually adjust the closeness of the

cut. For the closest cut and the shortest hair,

push taper lever up as far as it will go, to level

#1. For a longer cut, slowly push lever down. If

you push to the lowest position, level #5, it will

leave hair about the same length as the short

comb attachment.

Because a different cutting edge is used in

each setting, using the taper lever lengthens

the life of your blades.

Packed-in hair can slow down any clipper. To

remove hair without removing the blades, do

what the professionals do: Keeping the clipper

on, quickly push the taper lever back and forth

from close cut to longer cut a few times.

If you do this after every clipping, especially

with heavy hair cutting, the blades should

remain free of cut hair.

NOTE: Never pull on the clipper cord. Never

twist or wrap the cord around the clipper. Lay

it flat with the cord coiled up when not in use.

STORAGE: When not in use, your clipper

should be disconnected, allowed to cool and

stored in a safe, dry location, out of reach of

children.

Close Cut

Longer Cut

BATTERY SAFETY INFORMATION

1. This device requires one 18650 lithium-ion

battery.

2. Battery is not to be removed by the consumer

unless instructed by the manufacturer.

3. Since the battery is sensitive to high

temperatures, when storing the device, keep it

in a cool, dry place.

4. Never put batteries into a fire.

5. Switch off device after use.

6. Keep batteries away from children, especially

the batteries that are small enough to ingest.

7. If a battery is ingested, seek immediate

medical help.

8. Never open, crush, puncture or disassemble

a battery.

9. Dispose of battery according to any state and

local regulations.

10. Do not dispose of rechargeable battery as

solid waste.

BATTERY DISPOSAL

This appliance contains a lithium-ion battery.

To protect the environment, this appliance

and its battery must be disposed of safely. At

the end of its life, please take this appliance

to a recycling center, where the internal

rechargeable battery should be removed by a

professional and recycled separately. For more

information about the recycling of electrical and

battery-operated appliances, please contact

your local recycling or environmental protection

office or your household waste disposal service.

For specific questions regarding replacement of

the battery in this product, please contact our

Conair Customer Care Line at 1-800-3-CONAIR.

To find the nearest drop-off recycling location,

call 1-800-822-8837 or visit www.call2recycle.

org/locator/

CONTAINS LITHIUM-ION BATTERY.

MUST BE COLLECTED, RECYCLED

OR DISPOSED OF PROPERLY.

DO NOT DISPOSE OF IN THE

MUNICIPAL WASTE.

BATTERY REMOVAL

1. Carefully remove power switch.

2. Remove the screws and detach end cover on

bottom of clipper.

3. Remove the screws from outer housing.

4. Remove clipper handle sleeve.

5. Remove top housing.

6. Remove used lithium battery.

Note: The product you have purchased

contains a rechargeable battery. The battery is

recyclable.

At the end of its useful life, under various state

and local laws, it may be illegal to dispose of

this battery into the municipal waste stream.

Check with your local solid-waste officials for

details in your area for recycling options or

proper disposal.

5. Dismantle top housing

1. Dismantle switch

6. Remove battery

2. Remove screws

and end cover

3. Remove screws

4. Remove handle sleeve

WARNING:

IF YOU THINK

THE POWER IS OFF

WHEN THE SWITCH

IS OFF,

YOU’RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water

are a dangerous combination. But did you

know that an electric appliance is still

electrically live even if the switch is off? If

the plug is in, the power is on. So when you

are not using your appliances, keep them

unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED FIVE-YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your

unit free of charge for 60 months from the date of

purchase if the appliance is defective in workmanship

or materials.

To obtain service under this warranty, return the

defective product to the service center listed on back,

together with your purchase receipt. California

residents need only provide proof of purchase and

should call 1-800-3-CONAIR for shipping instructions.

In the absence of a purchase receipt, the warranty

period shall be 60 months from the date of

manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED IN

DURATION TO THE 60-MONTH DURATION OF THIS

WRITTEN, LIMITED WARRANTY. Some states do not

allow limitations on how long an implied warranty

lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH OF THIS

OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,

WHATSOEVER. Some states do not allow the exclusion

or limitation of special, incidental, or consequential

damages, so the above limitation may not apply to

you.

This warranty gives you speciﬁc legal rights, and you

may also have other rights, which vary from state to

state.

Locking taper

control

Stainless steel

self-sharpening

blades

High-torque

professional

DC motor

ON/OFF

switch

Durable metal

handle

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	Close Cut Precision HC6500

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair Close Cut Precision HC6500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Conair CD117NN Manual

2 September 2024

Conair LLT2 Manual

2 September 2024

Conair CLS1X Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Gigabyte ODIN GT 550W Manual

23 November 2024

Vitec MGW Diamond-HX OG Manual

23 November 2024

Stamos SWG-PTABLE-100PCT Manual

23 November 2024

Stamos S-PLASMA 60U Manual

23 November 2024

Velbus VMBPIRO-W-20 Manual

23 November 2024

Honor 90 Pro Manual

23 November 2024

Honor 80 SE Manual

23 November 2024

Medela Safe & Dry Manual

22 November 2024

Stamos S-PLASMA 70-IGBT Manual

22 November 2024

Jane First Potty Manual

22 November 2024