Conair GMT100R Manual


Læs nedenfor 📖 manual på dansk for Conair GMT100R (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
1. It is always best to begin with a clean, slightly
®
T R I M M E R
B A T T E R Y O P E R A T E D
BEARD MUSTACHE
NOSE/Ear trimmEr
For your safety and continued enjoyment
of this product, always read the instruction
booklet carefully before using.
Model GMT100RDCS
INSTRUCTIONS
FOR USE
1. Always purchase the correct size and grade of
battery most suitable for the intended use.
2. Replace all batteries of a set at the same time.
3. Clean the battery contacts and also those of
the device prior to battery installation.
4. Ensure the batteries are installed correctly
with regard to polarity (+ and -).
5. Remove batteries from equipment which is not
to be used for an extended period of time.
6. Remove used batteries promptly
SAVE THESE
INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
OPERATING INSTRUCTIONS:
1. Remove the battery compartment cover by
pushing in and down toward the bottom of the
trimmer.
2. Align the AA batteries with the positive and
negative positions indicated inside the battery
compartment. Being careful not to bend the clips,
insert the negative end of each battery first so it
will slip easily into position.
3. Return the battery cover to its original position
by pushing it in and up until you hear a small
click as it locks into place.
4. To use your trimmer, push ON/OFF switch up-
wards to ON position.
5. After you finish using your trimmer, push down
on the ON/OFF switch to turn the trimmer off.
On/Off Switch
*Requires 2 AA batteries (not included). We recommend
using alkaline batteries in your trimmer because they
last longer.
Do not mix old and new batteries. Do not mix alkaline,
standard (carbon zinc), or rechargeable (nickel cadmium)
batteries
TAKING CARE
OF YOUR TRIMMER
OILING THE BLADES
About once a month you should oil the trimmer
blades. It is best to do this over a piece of news-
paper. Turn the trimmer on and hold it so that the
blades are pointed downward. Spread one drop of
oil across the blades, then turn the trimmer off and
wipe away the excess oil with a soft cloth.
Be careful not to use too much oil and don’t oil
your trimmer more than necessary, as this could
damage the motor. (Never attempt to oil the motor
bearing as it is permanently lubricated.)
Keep oil out of reach of children.
BLADE CARE
Because the trimmer blades are precision made
for a very special use, they should always be
handled with care. This trimmer comes with a
removable blade set for easy cleaning. To remove
the blades follow these steps:
1. Make sure the trimmer is off, and the batteries
have been removed.
2. With the power switch facing you, gently push
up under the blades until they pop off.
3. To replace, align the tabs on the bottom of the
blades inside the mounting area on the back of
the trimmer and push down until the blades snap
into place. Each time you finish using the trim-
mer, take the cleaning brush provided and brush
away any loose hair that has collected in the
blades. Then store the trimmer until the next use.
Be especially careful when changing or adjusting
blades. When you have your trimmer serviced,
be sure that all blades are sharpened or replaced
at the same time.
To promote the long life of the appliance, use your
trimmer only for the purpose intended by the manu-
facturer to trim your beard and mustache.
GROWING A BEARD
AND MUSTACHE
There are three key factors that determine which
beard or mustache style is most suitable for
your face:
1. The shape and dimensions of your face.
2. The natural growth of your beard/mustache.
3. The thickness of your beard/mustache.
If you are unsure of the type of beard or mus-
tache that most suits your face, speak with a
professional hair stylist and ask for an opinion
on what style would be best.
TYPES OF BEARDS/MUSTACHES
Once your beard or mustache has been styled,
it is essential that you maintain its appearance.
To do this, use your shaper to trim your beard/
mustache weekly.
For the best trimming results, your beard should
be slightly damp (not wet) before using the trim-
mer. This will prevent the trimmer from removing
more hair than desired.
GETTING STARTED
OUTLINING YOUR BEARD
damp beard.
2. After you have combed
through your beard in the
direction it grows natu-
rally, you will want to
outline the desired shape,
beginning under your jawline.
3. Begin defining your
beards shape under
your chin and work
upward on each side of
your face toward your
ears. Then define the upper outline of your beard
across your cheeks, past your sideburns and
toward your hairline.
NOW YOU’RE READY
TO TRIM YOUR BEARD
1. Your trimmer adjusts to five positions so you
can have a beard length from 1/8" (shortest) to
5/8" (longest).
2. To use the 5-position comb, slide it over the
trimmer blades and snap down into position. At
first, until you become familiar with the adjust-
ments, use the longest trim setting (5/8"). (You
can always go back and make your beard a
little shorter.)
3. Begin trimming your beard using smooth,
even strokes. Start with your sideburns and work
downward toward your chin. (Never attempt to
trim against the natural growth of your beard,
because the hair will be cut too short.)
4. If you decide you want a closer trim, you can
now adjust the 5-position comb to a shorter set-
ting (such as 1/2" or 3/8") and go over your beard
again until you achieve the desired length.
TO TRIM YOUR MUSTACHE
1. For best results, start with a clean, slightly
damp mustache.
2. Comb through your mus-
tache in the direction it grows.
3. Place the 5-position comb
over the trimmer blades and
snap it into position. It is a
good idea to start with the longest trim setting
adjustment. (You can always go back and cut your
mustache more closely with a shorter setting.)
ALWAYS TRIM YOUR MUSTACHE
FROM THE TOP DOWN
After your mustache has
been trimmed to the desired
length, remove the 5-way
trimming attachment and,
using the blades only, define
the outline of the bottom of
your mustache.
USING THE NOSE/EAR
HAIR ATTACHMENT
1. Make sure the trimmer on/off switch is in the
“off” position. Detach the normal trimming blade
(see section on Blade Care). Fit the tab on the
back of the nose/ear hair attachment into the
notch inside the trimmer head. Push the attach-
ment towards the front of the trimmer until it
snaps into place. Turn the on/off switch to the
“on” position. While detaching the attachment,
make sure the power switch is facing you and
press the attachment away from you.
SAVE THESE INSTRUCTIONS
TROUBLE SHOOTING
There are several things to look for if your trim-
mer fails to operate:
1. Be sure the trimmer is turned ON.
2. Make sure that the batteries are properly
placed in the battery compartment. Test the bat-
teries to be sure they are working. (For optimum
trimmer operation, always replace all two AA
batteries at the same time.)
3. Check the blades to see if they are clogged
with hair clippings; if so, use the cleaning brush
to remove hair.
4. If the trimmer still fails to operate, take or
send it to a Conair Service Center (see warranty
procedure and addresses).
GMT100RDCS
BEARD/MUSTACHE TRIMMER
5-Position Comb
Nose/Ear Hair
Attachment
Trimmer
LIMITED TWO YEAR WARRANTY
Conair will repair or replace, at our option, your
appliance free of charge for 24 months from the
date of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return the
defective product to the service center listed on
back, together with your sales slip and $3.00 for
postage and handling. California residents need
only provide proof of purchase and should call
1-800-3-CONAIR for shipping instructions. In the
absence of a receipt, the warranty period shall be
24 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTY OF MERCHANT ABILI-
TY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED IN DURATION TO THE 24
MONTH DURATION OF THIS WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. Some states do not allow the
exclusion or limitation of special, incidental, or
consequential damages, so the above limitation
may not apply to you.
This warranty gives you specific legal rights, and
you may also have other rights which vary from
state to state.
Please register this product at:
www.conair.com/registration
©2012 Conair Corporation
Service Center:
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
12PG128105 IB-11162


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: GMT100R

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair GMT100R stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024