Conair GMTL1R Manual


Læs nedenfor 📖 manual på dansk for Conair GMTL1R (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
k
e
e
®
ALL-IN-1
LITHIUM BEARD & MUSTACHE
T R I M M E R R E C H A R g E A B L E
Instruction Booklet
For your safety and continued enjoyment
of this product, always read the instruction
booklet carefully before using.
Model GMTL1
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially when
children are present, basic safety precautions should
always be taken, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
FOR HOUSEHOLD USE ONLY
KEEP AWAY FROM WATER
DANGER Any appliance is
electrically live, even when the switch is off.
To reduce the risk of death or injury by electric shock:
1. Always unplug appliance from electrical
outlet immediately after using (except when
charging unit).
2. Do not place or store appliance where it could
fall or be pulled into a tub or sink.
3. Do not use appliance while bathing or in the
shower.
4. Do not place appliance in, or drop into water or
other liquids.
5. If appliance has fallen into water, do not
reach for it. Unplug immediately.
6. Unplug this appliance before cleaning.
WARNING To reduce the risk
of burns, electric shock, fire, or injury to persons:
1. Never leave a plugged-in appliance unattended.
2. This appliance should not be used by, on, or near
children or individuals with certain disabilities.
3. Use appliance only for its intended use as
described in this manual. Use only attachments
recommended by the manufacturer. Do not use an
extension cord to operate the appliance.
4. Never operate the appliance if it has a
damaged cord or plug, is not working properly,
has been dropped or damaged, or dropped into
water. Return the appliance to a Conair Service
Center for examination and repair.
5. Keep the appliance cord away from heated
surfaces.
6. Do not pull, twist or wrap the cord around the
appliance.
7. Never drop or insert any object into any opening
on the appliance.
8. Do not place the appliance on any surface while
it is operating.
9. Do not use the appliance with a damaged or bro-
ken comb or with teeth missing from the blades, as
injury may result. Before each use, make certain
the blades are aligned properly and oiled.
10. Do not use the appliance outdoors or where
aerosol (spray) products are being used or oxygen
is being administered.
11. THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
SAVE THESE
INSTRUCTIONS
USER MANUAL
Before using the Class 2 Power Supply,
read these instructions carefully.
Use with adapter C12
Rated input voltage:
100–240V AC, 50/60Hz 0.2A Max
Rated output: 4.5V DC 1000mA
OPERATION
1. For dry location use only. Do not expose to water.
2. When not in use, unplug unit completely.
3. Unit will become warm during operation.
CAUTION
1. Dry location use only. Do not expose to liquids,
vapor, or rain.
2. Ensure jack is plugged into the trimmer unit
before plugging the adapter into the outlet.
3. Do not operate any appliance that has a damaged
output cord or housing.
4. Always unplug the unit before cleaning or when
not in use.
5. This power unit is intended to be correctly
oriented in a vertical or floor mount position.
6. Be sure voltage is correct before plugging in.
For connection to a supply not in the U.S.A. use an
attachment plug adapter of the proper configuration
for power outlet.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Warning: Changes or modification to this unit not
expressly approved by the party responsible for
compliance could void the users authority to operate
the equipment.
TROUBLESHOOTING
If your rechargeable trimmer does not seem to be
taking a charge, take the following troubleshooting
steps before returning it for repair:
1. Be sure the electrical outlet is working by
plugging in another appliance to test the outlet.
2. Make sure the electrical plug is not connected
to a switch that turns power off when lights are
turned off.
OPERATING
INSTRUCTIONS
1. Before using the trimmer for the first time,
charge continuously for 2 hours. Maximum bat-
tery capacity will be reached only after 3 charg-
ing and discharging cycles.
2. Plug the adapter into any wall outlet (at the
voltage listed on the label affixed to the adapter).
Unplug adapter when not in use.
3. The adapter may become warm while charging.
This is normal.
4. Preserving the batteries: In order to maintain the
optimum capacity of the rechargeable batteries, the
trimmer should be recharged for 2 hours approxi-
mately every 6 months.
USER MAINTENANCE
INSTRUCTIONS
TAKING CARE OF YOUR TRIMMER
OILING THE BLADES (OIL INCLUDED)
About once a month you should oil the trimmer blades
with the oil provided in your kit. It is best to do this over
a piece of newspaper. Turn the trimmer on and hold it so
that the blades are pointed downward. Spread one drop
of oil across the blades, then turn the trimmer off and
wipe away the excess oil with a soft cloth.
Be careful not to use too much oil and don’t oil your
trimmer more than necessary, as this could damage the
motor. (Never attempt to oil the motor bearing, as it is
permanently lubricated.) Keep oil away from children.
BLADE CARE
Because the trimmer blades are precision-made
for a very special use, they should always be
handled with care and cleaned regularly to ensure
maximum performance. Each time you finish using
the trimmer, take the cleaning brush provided and
brush away any loose hair that has collected in the
blades. You can also remove the blade attachment
and rinse under warm water only. Do NOT use hot
water as this might cause damage. Use a clean
cloth to dry the attachment, reattach and then store
the trimmer to protect the blades until the next use.
DO NOT RINSE TRIMMER HANDLE OR ADAPTER
Be especially careful when changing or adjusting the
blades. When you have your trimmer serviced, be
sure that both blades are sharpened or replaced at
the same time.
To promote the long life of the trimmer, use it only for
the purpose intended by the manufacturer to trim
your beard and mustache.
GROWING A BEARD AND MUSTACHE
There are three key factors that will determine which
beard or mustache style is best for you:
1. The shape and dimensions of your face.
2. The natural growth of your beard/mustache.
3. The thickness of your beard/mustache. If you are
unsure about the type of beard or mustache that
would most suit your face, speak with a professional
hair stylist and ask for an opinion on what style would
be best. Once your beard or mustache has been
styled, it is essential that you maintain its appear-
ance. To do this, use your trimmer to trim your beard/
mustache weekly.
For the best trimming results, your beard should be
slightly damp (NOT WET) when using your trimmer.
This will prevent the trimmer from removing more
hair than desired.
TYPES OF BEARDS/MUSTACHES
GETTING STARTED
OUTLINING YOUR BEARD
1. It is always best to begin with a clean, slightly
damp beard.
2. After you have combed through your beard in the
direction it grows naturally, you will want to outline
the desired shape, beginning under your jawline.
3. Begin defining your beard’s
shape under your chin and wor
upward on each side of your fac
toward your ears. Then defin
the upper outline of your beard
across your cheeks, past your sideburns, and toward
your hairline.
TRIMMING YOUR BEARD
1. The trimmer includes a 6-position comb for use with
the hair trimming blade (4–18mm) which provides
lengths of 4/25" (shortest) to 7/10" (longest).
2. To use the 6-position comb, slide
the unit over the trimmer blade and
snap it down into position. At first,
until you become familiar with the
adjustments, use the longest trim
setting. (You can always go back and make your beard
a little shorter.)
3. Begin trimming your beard using smooth, even
strokes. Start with your sideburns and work downward
toward your chin. (Never attempt to trim against the
natural growth of your beard because the hair will be
cut too short.)
4. If you decide you want
a closer trim, you can now
adjust the 6-position comb
attachment to a shorter
setting (such as 3/32" or
5/32") and go over your beard again until you achieve
the desired length.
HOW TO GET THE STUBBLE LOOK
This trimmer includes 1 stubble comb
that allows you to achieve close stubble
or shadow looks. The stubble comb fits
on the blade just like the jawline combs;
note Blending the Jawline section for
specifics on how comb/jawline combs
attach.
BLENDING THE JAWLINE
1. The two jawline comb attachments will help you
to achieve a neat, finished trim under your chin. To
use one of the attachment combs, press it down
over the trimmer blades until it clicks into position.
2. Hold the trimmer in an upright position and begin
trimming under your jawline, using short, even
strokes.
3. After your beard is blended, turn off the trimmer
and remove the attachment comb by gently pulling
up on tab.
JAWLINE COMB I JAWLINE COMB II
TRIMMING YOUR MUSTACHE
1. For best results, start
with a clean, slightly damp
mustache.
2. Comb through your mus-
tache in the direction it grows.
3. Place the 6-position comb over the facial hair
blade and snap it into position. It is a good idea to
start with the longest trim-setting adjustment. (You
can always go back and cut your mustache more
closely with a shorter setting.)
ALWAYS TRIM YOUR MUSTACHE
FROM THE TOP DOWN
4. After your mustache has
been trimmed to the desired
length, remove the 6-position
comb and, using the blades
only, define the outline of the
bottom of your mustache.
SHAVING FOIL
Your trimmer includes a shaving foil. When attached,
it will allow you to shave close and around your
facial hair to provide an extra-clean look. Just move
the shaving head in up-and-down gentle strokes
to remove any stray hairs. Be sure not to press too
hard, as that could cause some skin irritation.
After each use clean the shaving head as follows:
1. Make sure the trimmer is off.
2. Remove the shaving head from the unit.
3. Remove the foil head from the shaving head
(press the two buttons on either side of the shaving
head and pull the foil head away).
4. Use the cleaning brush to gently remove any
hairs from the cutter and shaving head.
Do not rinse or oil the foil head as it is perma-
nently lubricated.
NOSE/EAR & DETAIL TRIMMER
For easy, safe grooming of long nose/ear hairs and
fine lines and accurate detailing. Attach the nose/
ear & detail trimmer and hold unit to areas that
need trimming.
Switch the trimmer on.
Gently move the blade through the area of hair
you wish to trim.
The trimmer will work most efficiently when cut-
ting through hair at its own speed.
Never turn the trimmer off while in the hair.
ON/OFF SWITCH
To operate, simply slide switch toward blade. To stop,
slide away from blade.
CARE OF YOUR TRIMMER
REPLACEMENT (REMOVAL) OF BLADE SET
To remove the blade set from
your trimmer, make sure the
trimmer is in the OFF position.
Remove the blade set by placing
thumb against the smaller cutter
and pushing forward, releasing the
cutter assembly from the trimmer
housing.
BATTERY REMOVAL
1. Using a small Phillips head screwdriver, remove the
screws at the back of the trimmer.
2. Remove the bottom housing and cut the battery
out. Bring the battery to the nearest collection center
for proper disposal. DO NOT throw the battery into the
normal municipal waste system.
GMTL1 LITHIUM BEARD/MUSTACHE TRIMMER
2 Jawline Combs
6-Position
Comb Attachment
Stubble Comb
Facial Hair Blade
Trimmer
Lubricating OilCleaning Brush
Adapter
N /ENose/Ear/Detail/D il
Multi-Use Trimmer
LIMITED TWO-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 24 months from the date of
purchase if the appliance is defective in workman-
ship or materials.
To obtain service under this warranty, return the
defective product to the service center listed on
back, together with your purchase receipt and
$3.00 for postage and handling. California residents
need only provide proof of purchase and should call
1-800-3-CONAIR for shipping instructions. In the
absence of a purchase receipt, the warranty period
shall be 24 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED IN DURATION TO THE
24-MONTH DURATION OF THIS WRITTEN, LIMITED
WARRANTY. Some states do not allow limitations
on how long an implied warranty lasts, so the above
limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or limitation
of special, incidental, or consequential damages, so
the above limitation may not apply to you.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from state
to state.
Please register this product at:
www.conair.com/registration
©2016 Conair Corporation
Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
15PG017304 IB-14016
SHEAD-GMTL1
BLD-161
2JAW-GMTL1
BLD-165
6POS-GMTL1
STUB-1
CUT HERE
TRIMMER REPLACEMENT PARTS & ACCESSORIES ORDER FORM
Pricing in effect through June 1, 2018. Orders postmarked after this date
will be accepted, and the customer will be notified if pricing has changed.
Trimmer Attachment Blade BLD-161 $6.50
Shaving Foil SHEAD-GMTL1 $6.50
Stubble Comb STUB-1 $2.25
6-Position Comb Attachment 6POS-GMTL1 $2.25
Nose/Ear/Detail Trimmer BLD-165 $5.50
2 Jawline Combs $5.502JAW-GMTL1
ITEM PRICE PART # QUANTITY AMOUNT
Subtotal
Sales Tax*
TOTAL
Mail to:
Conair Corporation
Service Department
150 Milford Road
East Windsor, NJ 08520-9730
Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or
C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax. Minimum
order of $10.00 or a $2.00 handling charge will be added to order.
All prices include handling and return postage. Prices are subject to change without notice.
Prices are valid only for shipments within the continental United States. Please allow 4–6 weeks
for delivery.
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. box.
NAME _________________________________________________________________________________________________
ADDRESS ___________________________________________ APT. ______________________________________________
CITY ________________________________________________STATE _________ ZIP________________________________
TELEPHONE ( ) _____________________________________________________________
(We call only if we have a question about your order.)
For information on other Conair
®
haircut kit parts call: 1-800-3-CONAIR.


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: GMTL1R

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair GMTL1R stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024