Conair GMTL30 Manual


Læs nedenfor 📖 manual på dansk for Conair GMTL30 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Respect the Ritual®
HIGH P E RFORMA N CE M E T A L T R I MMER
Instruction Booklet
For your safety and continued enjoyment
of this product, always read the instruction
booklet carefully before using.
Model GMTL30
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially when
children are present, basic safety precautions
should always be taken, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
FOR HOUSEHOLD USE ONLY
KEEP AWAY FROM WATER
DANGER To reduce the risk of
death or serious injury from electrical shock:
1. Do not place or store appliance where it can fall
or be pulled into a tub or sink. Do not place or drop
appliance into water or other liquids.
2. Except when charging, always unplug this
appliance from the electrical outlet immediately
after using.
3. Always turn this appliance off before cleaning.
4. Do not reach for an appliance that has fallen
into water.
WARNING To reduce the risk of
burns, electric shock, fire, or injury to persons:
1. Except when charging, never leave a
plugged-in appliance unattended.
2. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning the use
of the appliance by a person responsible for their
safety. Children should be supervised to ensure
that they do not play with the appliance.
3. Use appliance only for its intended use as
described in this manual. Use only attachments
recommended by the manufacturer. Do not use an
extension cord to operate the appliance.
4. Never operate the appliance if it has a
damaged cord or plug, is not working properly,
has been dropped or damaged, or has been
dropped into water. Return the appliance to
a Conair Service Center for examination and
repair.
5. Keep the appliance cord away from
heated surfaces.
6. Do not pull, twist or wrap the cord around
the appliance.
7. Never drop or insert any object into any opening
on the appliance.
8. Do not place the appliance on any surface while
it is operating.
9. Do not use the appliance with a damaged or
broken comb or with teeth missing from the blades,
as injury may result. Before each use, make certain
the blades are aligned properly and oiled.
10. Do not use the appliance outdoors or where
aerosol (spray) products are being used or where
oxygen is being administered.
11. This appliance is not a toy. Keep away from
children.
12. THIS PRODUCT IS FOR HOUSEHOLD
USE ONLY.
FEDERAL COMMUNICATIONS
COMMISSION NOTICE
WARNING: Changes or modifications
to this unit not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
SUPPLIER’S DECLARATION
OF CONFORMITY
Brand: Conairman®
Model No.: GMTL30
Description: Trimmer
Responsible Party: Conair Corporation,
1 Cummings Point Road,
Stamford, CT 06902 (203) 351-9000
Standards: FCC Part 15 Subpart B,
ANSI C63.4-2014
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that
may cause undesirable operation.
DATE OF ISSUE: November 20, 2020
SAVE THESE
INSTRUCTIONS
USER MANUAL
Before using the Class 2 Power Supply,
read these instructions carefully.
Use with adapter CA74
Rated input voltage:
100–240V AC, 50/60Hz 0.3A
Rated output: 5.0V DC 1000mA
CAUTION
1. Ensure jack is plugged into the trimmer unit before
plugging the adapter into the outlet.
2. Do not operate any appliance that has a damaged
output cord or housing.
3. Always unplug the unit before cleaning or when
not in use.
4. This power unit is intended to be correctly
oriented in a vertical or floor-mount position.
5. Be sure voltage is correct before plugging in.
For connection to a power supply not in the U.S.A,
use an attachment plug adapter of the proper
configuration for power outlet. The adapter included
automatically adjusts to the input voltage. DO NOT
USE WITH A VOLTAGE CONVERTER.
TRIMMER OPERATING
PRECAUTIONS
This trimmer has a built-in rechargeable battery.
Do not throw into fire, apply heat, or charge, use
or leave in a high-temperature environment.
CAUTION: Any changes or modifications not
expressly approved by the Conair
® Corporation,
the manufacturer of this product and the party
responsible for compliance, could void the user’s
authority to operate the equipment.
TROUBLESHOOTING
If your rechargeable trimmer does not seem to be
taking a charge, take the following troubleshooting
steps before returning it for repair:
1. Be sure the electrical outlet is working by
plugging in another appliance to test the outlet.
2. Make sure the electrical plug is not connected
to a switch that turns power off when lights are
turned off.
3. Make sure the adapter is inserted into the trimmer
properly and all the connections are secure.
OPERATING
INSTRUCTIONS
CHARGING
1. Before using the trimmer for the first time,
charge continuously for 3 hours. Maximum
battery capacity will be reached only af ter 3
charging and discharging cycles.
2. To charge the trimmer, first ensure the trimmer
is switched off, plug the USB cable into the USB
port on the USB adapter with output 5.0V DC,
1000mA, then insert the Micro USB plug into
the bottom of the trimmer. Plug the adapter into
any wall outlet (at the voltage listed on the label
affixed to the adapter). Unplug adapter when not
in use.
3. The adapter may become warm while charging,
this is normal.
4. The blue charging LED indicator light on the
trimmer will flash when correctly connected.
When it is fully charged, the blue charging LED
indicator light will stay blue and stop flashing.
5. A full charge will supply 60 minutes of cordless
runtime.
6. When the trimmer is running low on a charge,
the LED indicator light will flash, warning that
there is approximately 6 minutes of battery use
remaining.
7. When charging, the unit can’t operate.
8. To maintain optimum capacity of the
rechargeable battery, it is highly recommended to
fully discharge and then recharge the trimmer for
3 hours every 6 months.
WARNING: If the charging light suddenly
starts to flash rapidly, the appliance is faulty. If
this happens, please stop charging and remove
the adapter from the outlet and contact our
customer care center for further advice.
TRIMMER CHARGING
PRECAUTIONS
Avoid charging the battery at temperatures
below 41°F (5°C) or above 95°F (35°C).
Avoid charging the battery in direct sunlight or
near a radiating heat source.
Even though the trimmer may not be used for
an extended period of time, charge once a month
to preserve battery life.
The power cord cannot be replaced. If it is
damaged, the DC adapter should be discarded.
CORDLESS OPERATION
Plug the USB cable into the USB port on the
USB adaptor with output 5.0V DC,1000mA, insert
the Micro USB plug into the bottom of the trimmer
and then plug it into a suitable outlet and switch
off. The LED light will appear when the adapter
is correctly inserted into the appliance and
connected to the outlet.
When charging the appliance with the adapter,
switch the trimmer on and, if it still does not
work, then keep charging.
Once the appliance is fully charged, the blue
LED light will stop flashing, but remain on. Unplug
the adapter from the outlet, then the appliance
and prepare for use.
USER
MAINTENANCE
INSTRUCTIONS
REMOVING THE BLADE SET
1. Make sure the trimmer is in the
OFF position.
2. Place your thumb against the
smaller cutter and push up to
remove the blade set.
REPLACING THE BLADE SET
1. Make sure the trimmer is in the OFF position.
2. Align the back prong of the trimmer blade with
the guide slot on the trimmer housing, place your
thumb on top of the blade and snap into place.
OILING THE BLADES
1. Oil the trimmer once a month.
2. Turn the trimmer on.
3. Hold and point the blades downward.
4. Spread one drop of oil across the blades
5. Turn the trimmer off and wipe away any
excess oil.
NOTE:
1. Do not over-oil the blades, as this can damage
the motor.
2. Do not oil the motor bearing, as it is
permanently lubricated.
3. KEEP OIL AWAY FROM CHILDREN.
BLADE CARE
1. Brush away any loose hair that collects in
the blades.
2. Store the trimmer in a safe location.
3. Sharpen or replace both blades at the same
time when servicing your trimmer.
4. Only use Conair
® blades with this trimmer
(see Parts & Accessories form).
5. Use trimmer for facial hair only.
OUTLINING YOUR
BEARD
1. Start with a clean, slightly
damp beard (NOT WET).
2. Comb through your beard in the direction it
grows naturally.
3. Begin under your jawline.
4. Trim from your chin upward, toward your ears.
5. Finish upper outline across cheeks.
TRIMMING YOUR BEARD
1. On the longest setting,
begin trimming your
beard using smooth,
even strokes. Start with
your sideburns and work
downward toward your chin. (Never attempt to
trim against the natural growth of your beard
because the hair will be cut too short.)
2. If you decide you want a closer
trim, adjust the 5-position comb
attachment to a shorter setting
and go over your beard until you
achieve the desired length.
HOW TO GET THE STUBBLE LOOK
This trimmer includes a stubble comb that allows
you to achieve different looks of stubble or shadow
looks with your already existing growth. Simply use
the comb for the look you would like to achieve.
The stubble comb fits on the blade just like the
jawline combs (note Blending the Jawline section
for specifics on how combs/jawline combs are
attached).
BLENDING THE JAWLINE
Attach a jawline comb to the trimmer, hold the
trimmer in an upright position and begin trimming
under your jawline, using short, even strokes.
TRIMMING YOUR MUSTACHE
1. Start with a clean,
slightly damp mustache
(NOT WET).
2. Comb through your
mustache in the direction
it grows.
3. Trim your mustache from the top down; finish
by outlining the bottom of your mustache.
4. Start with the 5-position attachment comb on
the longest setting, as you can always go back
and shorten the length as desired.
SHAVING FOIL
1. Make sure the trimmer is in the OFF position.
2. Align the single prong at the bottom of the
shaver head with the guide slot in the shaver unit,
Then push down and forward.
3. Use by applying gentle up and down strokes.
4. To detach the foil shaver: hold the trimmer with
your thumb pressing the top, front part of the
trimmer head and snap it off. Do not rinse or oil the
foil head as it is permanently lubricated.
ROTARY NOSE & EAR TRIMMER
1. Make sure the trimmer is in
the OFF position.
2. Insert the pin of the trimmer
body into the hexagonal hole
of the nose and ear trimmer
head as shown (Fig. 1).
3. Press and snap the trimmer
head onto the body as shown
(Fig. 2).
4. Use trimmer in a circular
motion.
5. To detach the nose and
ear trimmer: Hold the trimmer
as shown (Fig. 3), with the
thumb pressing the top, front
part of the trimmer head, and
snap it off.
Fig. 1
Fig. 2
Fig. 3
BATTERY REMOVAL
NOTE: At the end of the battery’s useful life, under various state and local laws, it may be illegal to
dispose of the battery into the municipal waste stream. Check with your local solid waste officials for
details in your area for recycling options or proper disposal.
CONTAINS LITHIUM ION BATTERY.
MUST BE COLLECTED, RECYCLED
OR DISPOSED OF PROPERLY.
DO NOT DISPOSE OF IN THE
MUNICIPAL WASTE.
3. Remove screws1. Detach blade head 4. Take apart end cap and
aluminum tube
3. Remove screws
6. Disassemble battery
2. Disassemble switch button
5. Remove screws
battery
GMTL30 PROFESSIONAL HAIR TRIMMER
3 Jawline Combs Stubble Comb
Storage Pouch
b
Ear/Nose
Hair Trimmer
Shaving Foil
USB Cable
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water
are a dangerous combination. But did you
know that an electric appliance is still
electrically live even if the switch is off? If
the plug is in, the power is on. So when you
are not using your appliances, keep them
unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED TWO-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 24 months from the date of
purchase if the appliance is defective in workman-
ship or materials.
To obtain service under this warranty, return the
defective product to the service center listed on
back, together with your purchase receipt. California
residents need only provide proof of purchase and
should call 1-800-3-CONAIR for shipping instruc-
tions. In the absence of a purchase receipt, the
warranty period shall be 24 months from the date
of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED IN DURATION TO THE
24-MONTH DURATION OF THIS WRITTEN, LIMITED
WARRANTY. Some states do not allow limitations
on how long an implied warranty lasts, so the above
limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or limitation
of special, incidental, or consequential damages, so
the above limitation may not apply to you.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from state
to state.
Please register this product at
www.conair.com/registration
©2021 Conair Corporation
Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
21PG075723 IB-17026A
5POS-189
BLD-189
3JAW-189
BLD-165
NOSE/EAR-189
CUT HERE
Trimmer Attachment Blade BLD-189 $6.50
Detailing Blade BLD-165 $5.50
5-Position Comb Attachment 5POS-189 $2.25
Rotary Nose/Ear Attachment NOSE/EAR-189 $5.50
3 Jawline Combs 3JAW-189 $5.50
HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM
OR PURCHASE ON THE WEB AT WWW.CONAIR.COM
Pricing in effect through December 31, 2025. Orders postmarked after this date will be accepted,
and the customer will be notified if pricing has changed.
ITEM PART # PRICE QUANTITY AMOUNT
Subtotal
Sales Tax*
TOTAL
Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D.
orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax. Minimum order of $10.00
or a $2.00 handling charge will be added to order.
All prices include handling and return postage. Prices are subject to change without notice. Prices
are valid only for shipments within the continental United States. Please allow 46 weeks for delivery.
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. Box.
NAME _________________________________________________________________________________________________
ADDRESS APT. ___________________________________________ ______________________________________________
CITY ________________________________ ________________________________________________STATE _________ ZIP
TELEPHONE ( ) ___________________________________________________________
(We call only if we have a question about your order.)
For information on other Conair® haircut kit parts call: 1-800-3-CONAIR.


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: GMTL30

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair GMTL30 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024