Conair HC1100N Manual

Conair Ikke kategoriseret HC1100N

Læs nedenfor 📖 manual på dansk for Conair HC1100N (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Attach comb

guide

Remove comb guide

Fig. 1

Fig. 2

Oil both

areas

Oil both

areas

hc1100_12pg129346_ib_final.indd 1 11/7/12 2:37 PM

Model HC1100

LITHIUM ION

CORD/CORDLESS CLIPPER

Instr uction Booklet

For your safety and continued enjoyment

of this product, always read the instruction

booklet carefully before using.

Full Power

Cord-Free

Cut tin g

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, take basic safety

precautions, including the following:

READ ALL INSTRUCTIONS

BEFORE USING

KEEP AWAY FROM WATER

FOR HOUSEHOLD USE ONLY

DANGER – any appliance is electrically

live, even when the switch is off.

To reduce the risk of death or injury by electric

shock:

1. Unplug this appliance before cleaning.

2. Do not place or store appliance where it can

fall or be pulled into a tub or sink.

3. Do not use while bathing or in a shower.

4. Do not place in, or drop into water or other

liquids.

5. Do not reach for an appliance that has fallen

into water. Unplug immediately. Dry location

use only or expose to liquid, vapor or rain.

6. Except when charging, always unplug this

appliance from electrical outlet immediately

after using.

7. Never operate the adapter if the specifica-

tion is out of the rating.

DO NOT REACH

INTO THE WATER

WARNING – To reduce the risk of

burns, electric shock, fire, or injury to persons:

1. This appliance should never be left

unattended when plugged in. Do not pull,

twist, or wrap line cord around appliance.

2. This appliance should not be used by, on

or near children or individuals with certain

disabilities.

3. Use this appliance only for its intended

purpose as described in this manual. Do not

use attachments not recommended by the

manufacturer. Do not use an extension cord to

operate this appliance.

4. Never operate this appliance if it has a

damaged cord or plug, if it is not working

properly or if it has been dropped or

damaged, or dropped into water. Return the

appliance to a service center for examination

and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any

opening on this appliance.

7. Do not place appliance on any surface while

it is operating.

8. Do not use this appliance with a damaged

or broken comb or with teeth missing from the

blades as injury may occur. Before use, make

certain blades are aligned properly. (See taking

care of your trimmer).

9. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

10. Never operate the appliance with the

air openings blocked or while on a soft

surface, such as a bed or couch, where the

air openings may be blocked. Keep the air

openings free of lint, hair, and other debris.

11. Always attach plug to appliance first, then

to outlet. To disconnect, turn all controls to

“OFF”, then remove plug from outlet.

12. Avoid skin contact with moving blade.

13. When using the appliance with its cord,

be mindful of tangles or kinks in the cord. If

the cord does become tangled during use,

turn the unit off and straighten cord before

operating again.

14. Do not short the polarity (output cord),

ensure jack is plugged into the unit before

plugging the adapter into outlet.

15. This power unit is intended to be correctly

oriented in vertical floor mount position.

16. For connection to a supply not in the

U.S.A., use an attachment plug adapter of the

proper configuration for the power outlet.

17. The adapter complies with Part 15 of

the FCC Rules. Operation is subject to the

following two conditions: (1) the adapter

may not cause harmful interference, and (2)

the adapter must accept any interference

received, including interference that may

cause undesired operation.

WARNING: Changes or modifications to this

unit not expressly approved by the party

responsible for compliance could void the

user’s authority to operate the equipment.

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

USER MANUAL

Also included are 10 attachment combs for

different hair lengths (including left and right

ear taper combs), barber scissors, a barber

comb with straight teeth, styling comb with

angled teeth, a full-length barber cape, and a

deluxe case for easy storage. It also comes

with lubricating oil, a cleaning brush and a

blade guard for easy maintenance and

protection of the clipper blades.

The Conair Clipper is a professional grade hair

clipper with Lithium Ion technology to give

sustained power performance for cord or cord-

less use. The precision-engineered hardened

steel blades have a unique super sharp cutting

angle for smooth, effortless cutting on any hair

length or type.

FEATURES

• Cord or Cordless operational clipper - use

corded for continuous power while plugged

into the outlet or use cordless for total flexibility

and control.

• Lithium-ion technology with lightweight DC

motor for powerful cutting action and sustained

power performance.

• Precision-engineered high grade hardened

steel blades with unique super sharp cutting

angle for smooth, effortless cutting.

• Lightweight for easy handling during use.

• Taper control for custom settings.

• 3 hour full charge for approximately 75

minutes of use.

• 15 minute quick charge for approximately

15 minutes of use.

INSTRUCTIONS

FOR USE

CHARGING THE APPLIANCE

IMPORTANT

Only use the adapter supplied with this

appliance. This clipper is so easy to use, but

before you do anything you must take your

time to charge the unit for 3 hours before its

ﬁ rst use. Even if you want to use it plugged in

straight from an outlet, this initial supercharge

ensures optimum power performance to give

smooth fast cutting every time. Maximum

battery capacity will only be reached after

3 charging/discharging cycles. A full

charge will provide approximately 75 minutes

use. When the clipper is about to run out of

power, the charging indicator will ﬂ ash and

you will have approximately 3 minutes of use

remaining. A 15 minute quick charge will

provide approximately 15 minutes use.

When charging the appliance the blue LED

charging light will ﬂ ash slowly and continu-

ously until the battery has fully charged, then

the blue LED charging light will stop ﬂ ashing

but remain on.

WARNING: If the charging light suddenly starts

to ﬂash rapidly then the appliance is faulty. If this

happens then please stop charging and remove

the adapter from the outlet and contact our

Customer Care Center for further advise (see the

“warranty” section of the information booklet).

CORDED OPERATION

• Ensure the appliance is switched off.

• Connect the adaptor to the base of the

appliance and plug the adapter into a suitable

outlet.

• The blue LED charging light will ﬂ ash when

the adapter is correctly inserted into the

appliance and connected to an outlet.

• The appliance is now ready for use.

NOTE: The appliance should not be used for

longer than 20 minutes when operated with

the cord.

CORDLESS OPERATION

• Insert the adapter into the base of the

appliance, plug into a suitable outlet and

switch on. The blue LED charging light will go

on when the adapter is correctly inserted into

the appliance and connected to an outlet.

• Once the appliance is fully charged the blue

LED charging light will stop ﬂ ashing but remain

on, unplug the adapter from the outlet.

OILING INSTRUCTIONS

IMPORTANT! It is highly recommended before

each use to oil the blades with the oil provided.

This ensures optimum cutting performance.

For the ﬁ rst use you will need to use the oil

supplied with the product, unscrew the cap

and cut off the very end of the plastic tube with

a pair of scissors to release the oil.

To oil the blades ensure the unit is switched

on. Gently squeeze the oil tube and apply 2

drops of oil onto the blades. Leave the unit on

for a few seconds to allow the oil to thoroughly

spread the length of the blades. Switch off the

unit and remove any excess oil by gently

dabbing with a cloth.

Be careful not to use too much oil and don’t oil

your clipper more than necessary, as this could

damage the motor. (Never attempt to oil the

motor bearing, as it is permanently lubricated).

KEEP OIL OUT OF REACH OF CHILDREN

PRESERVING THE BATTERIES

In order to maintain the optimum capacity of the

r echargeable batteries, the appliance has to be

fully discharged every 6 months approximately.

Then recharge the appliance to full capacity,

again for 3 hours.

COMB GUIDES

This appliance is supplied with 8 comb guides

and a left and right ear taper guide:

CUTTING LENGTH GRADE

3mm #1

6mm #2

9.5mm #3

13mm #4

16mm #5

19mm #6

22mm #7

25mm #8

• To attach a comb guide, ensure the

appliance is switched off. Position the comb

guide over the front of the clipper blade and

slide over the head. Push and click the rear of

the comb guide into position (see Fig.1).

• To remove the comb guide, ensure the

appliance is switched off. Push the tab on the

rear of the comb guide away from the head

and lift off (see Fig.2).

The appliance is also supplied with 2 taper

guides. The taper guides can be used above

the ear to get a clean line.

• Attach either the left or right guide

depending on which ear you are cutting

above.

• Angle the clipper and gently stroke around

the ear towards the back of the neck.

TAPER CONTROL

• The taper control provides a variety of total

settings for custom cuts.

• To increase the cutting length, push the

lever down.

• To reduce the cutting length, push the

lever up.

PREPARATION FOR USE

• Always inspect the appliance before use to

ensure the clipper blades are free from hair,

debris etc.

• For best performance, use on clean, dry hair

that has been combed until tangle-free.

• Ensure the appliance is sufﬁ ciently charged

or plugged into an outlet.

NOTE: The appliance should not be used for

longer than 20 minutes when operated from

an outlet.

CLIPPING

FOR AN ALL OVER EVEN CUT:

• Attach a comb guide as required – your

clipper is supplied with 8 comb guides

(grades 1-8). Each comb guide is labelled.

• Switch the clipper on and the blades will

start to move.

• Starting at the nape of the neck, hold the

clipper with the teeth of the clipper pointing

upwards, ensuring that the comb guide is

resting ﬂ at against the head.

• Slowly move the clipper upwards and

outwards through the hair towards your

crown, against the direction of the hair

growth. The comb guide will help to lift the

hair and the blades will cut the hair at the

desired length.

• Once the desired length is achieved at the

back of the hair, start clipping the top and

sides.

• Hold the clipper to the front of your hair

with the teeth pointing towards the back of

your head, and move the clipper towards your

crown. Repeat as necessary, moving in rows

from the front and the sides of your head to

the back.

• You should achieve an even length cut all

over your head.

FOR A SHORTER BACK AND SIDES, WITH

LENGTH ON THE TOP

• Attach the longer comb guide as required

for the top of your hair – your clipper is

supplied with 8 comb guides (grades 1-8).

Each comb guide is labelled.

• Switch the clipper on and the blades will

start to move.

• Hold the clipper to the front of your hair

with the teeth pointing towards the back of

your head and move the clipper towards your

crown. Repeat as necessary, moving in rows

from the front and the sides of your head to

the back.

• If you then wish to take the back and sides

of your hair to a shorter length, switch off the

appliance and attach a shorter comb guide.

• Starting at the nape of the neck, with the

comb guide ﬂ at against the head, move the

clipper upwards and outwards over the area

you want to take shorter.

• Repeat on the sides of the hair, starting with

the teeth of the clipper pointing upwards and

comb guide ﬂ at against the area above the

ear, again moving the clipper upwards and

outwards.

OUTLINING

• To tidy up the edges around your cut e.g.

neckline and sideburns, detach the comb

guides.

• Hold the appliance upside down, so the

front of the clipper is facing towards your

head.

• Hold the clipper straight on your sideburns

or neckline and move the clipper downwards.

This will give you a clean, smooth ﬁ nish.

CLEANING & MAINTENANCE

• Regular cleaning will maintain the high

performance of your appliance.

• Switch off and remove the power cord if

connected.

• Use the cleaning brush supplied to brush

away any hair and debris. Do not use a sharp

object to clean the trimmer blade.

• Gently blow away any hair trapped beneath

the blades.

• Ensure you clean the blades after each use

and before storing away.

• It is highly recommended to oil the blades

from time to time with the oil provided. This

ensures optimum cutting performance. For

the ﬁ rst use you will need to use the oil

supplied with the product, unscrew the cap

and cut off the very end of the plastic tube

with a pair of scissors to release the oil.

• To oil the blades ensure the unit is switched

on. Gently squeeze the oil tube and apply 2

drops of oil onto the blades. Leave the unit on

for a further few seconds to allow the oil to

thoroughly spread the length of the blades.

• Switch off the unit and remove any excess

oil by gently dabbing with a cloth.

BATTERY DISPOSAL

This appliance contains Lithium Ion batteries.

To protect the environment this appliance and

its batteries must be disposed of safely. At the

end of its life, please take this appliance to a

recycling center, where the internal recharge-

able battery should be removed by a

professional and recycled separately. For

more information about the recycling of

electrical and battery operated appliances

please contact your local council ofﬁ ce or

your household waste disposal service. For

speciﬁ c enquiries regarding the replacement

of batteries in this product please contact our

Conair Customer Care Line.

HC1100 CORD/CORDLESS CLIPPER

QUICQUICKQUICKKKCHARCHARGEGE

Taper

Control

Stainless steel,

self-sharpening

blades

High Power

Motor

On/Off

switch

3-hour full charge for

75 minutes of use or

15-minute quick charge

for 15 minutes of use.

LIMITED THREE YEAR WARRANTY

Conair will repair or replace (at our option)

your unit free of charge for 36 months from

the date of purchase if the appliance is

defective in workmanship or materials.

To obtain service under this warranty, return

the defective product to the service center

listed below, together with your purchase

receipt and $5.00 for postage and handling.

California residents need only provide proof

of purchase and should call 1-800-366-0937

for shipping instructions. In the absence of a

purchase receipt, the warranty period shall

be 36 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTY

OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, SHALL BE

LIMITED IN DURATION TO THE 36 MONTH

DURATION OF THIS WRITTEN, LIMITED

WARRANTY. Some states do not allow

limitations on how long an implied warranty

lasts, so the above limitations may not apply

to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH

OF THIS OR ANY OTHER WARRANTY,

EXPRESS OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or

limitation of special, incidental, or conse-

quential damages, so the above limitation

may not apply to you.

This warranty gives you specific legal rights,

and you may also have other rights, which

vary from state

to state.

Please register this product at:

www.conair.com/registration

Service Center

Conair Corporation

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

12PG129346

IB-11227

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	HC1100N

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HC1100N stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair NPTCCA01 Manual

10 December 2024

Conair True Glow PB8NPRF Manual

10 December 2024

Conair NPTCCA02 Manual

10 December 2024

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg KIT6PX Manual

23 December 2024

Smeg KIT6CX Manual

23 December 2024

Smeg GTA-6 Manual

23 December 2024

Lucide Casper i 79166/19/12 Manual

23 December 2024

Lucide Merlina 78193/30/66 Manual

23 December 2024

Lucide Pippa 77583/81/30 Manual

23 December 2024

Lucide Pia 45380/04/30 Manual

23 December 2024

Lucide Pia 45280/01/30 Manual

23 December 2024

Lucide Anaka 45179/03/30 Manual

23 December 2024

Lucide Zych 45156/01/97 Manual

23 December 2024