Conair HC2000 Manual


Læs nedenfor 📖 manual på dansk for Conair HC2000 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 18 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
B a r b e r s h o p
Serie s
Instruction Booklet
For your safety and continued enjoyment
of this product, always read the instruction
booklet carefully before using.
Model HC2000
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, take basic safety
precautions, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY
FROM WATER
FOR HOUSEHOLD
USE ONLY
DANGER Any appliance is
electrically live, even when the switch is off.
To reduce the risk of death or injury by
electric shock:
1. Unplug this appliance before cleaning.
2. Do not place or store appliance where it
can fall or be pulled into a tub or sink.
3. Do not use while bathing or in the shower.
4. Do not place in, or drop into water or
other liquids.
5. Do not reach for an appliance that has
fallen into water. Unplug it immediately.
For dry location use only. Do not expose to
liquids, vapor or rain.
6. Always unplug this appliance from electri-
cal outlet immediately after using.
WARNING To reduce the
risk of burns, electric shock, fire, or injury
to persons:
1. This appliance should never be left
unattended when plugged in. Do not pull,
twist, or wrap line cord around appliance.
2. This appliance should not be used by, on
or near children or individuals with certain
disabilities.
3. Use this appliance only for its intended
purpose as described in this manual. Do not
use attachments not recommended by the
manufacturer. Do not use an extension cord
to operate this appliance.
4. Never operate this appliance if it
has a damaged cord or plug, if it is not
working properly or if it has been dropped
or damaged, or dropped into water.
Return the appliance to a service center for
examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any
opening on this appliance.
7. Do not place appliance on any surface
while it is operating.
8. Do not use this appliance with a damaged
or broken comb or with teeth missing from
the blades as injury may occur. Before use,
make certain blades are aligned properly.
9. Do not use outdoors or operate where
aerosol (spray) products are being used or
where oxygen is being administered.
10. Never operate the appliance with the
air openings blocked or while on a soft
surface, such as a bed or couch, where the
air openings may be blocked. Keep the air
openings free of lint, hair, and other debris.
11. Always atta
to outlet. To disc
OFF, then remov
12. This applian
from children.
SA
INST
OP
INST
This appliance i
Use on alternati
60 hertz only.
This appliance h
blade is wider t
feature, this plu
way. If the plug
reverse the plug
a qualified elect
defeat this safe
Your new Conai
you need to ach
home. It feature
adjustable taper
self-sharpening
included are 9 c
hair lengths, barber comb, barber scissors,
barber cape, a soft storage case, lubricating
oil, and a blade guard for easy maintenance
of the clipper blades.
OILING THE BLADES (OIL INCLUDED)
1. Oil the clipper blades once a month
2. Turn the clipper ON
3. Hold and point the blades downward
4. Spread one drop of oil across the blades
5. Turn the clipper OFF and wipe away any
excess oil
KEEP OIL AWAY FROM CHILDREN.
THE CONAIR GUIDE TO CUTTING
HAIR AT HOME
Before you start:
1. Inspect your clipper. Make sure its free of
hair and dirt, properly oiled and running
smoothly.
2. Place the barber cape or a towel around
the neck of the person whose hair is to be
cut.
3. Seat the person so that his or her head is
at your eye level. This gives you greater
visibility and control.
4. First, comb hair until its tangle free. Then
hold clipper in a comfortable grip. Now you’re
ready to cut.
MEDIUM TO LONG CUT
To begin, cut only a small amount of hair
until you become used to the length each
attachment leaves the hair. Try the longest
attachment on the clipper first. If you want a
shorter cut, you can then use shorter combs.
• Short comb attachment (number 1) cuts
hair to 1/8" (3mm).
• Medium-Short comb attachment (number
2) cuts hair to 1/4" (6mm).
• Medium-Long comb attachment (number 3)
cuts hair to 3/8" (10mm).
• Long comb attachment (number 4) cuts hair
to 1/2" (13mm).
• Long comb attachment (number 5) cuts hair
to 5/8" (16mm).
• Long comb attachment (number 6) cuts hair
to 3/4" (19mm).
• Long comb attachment (number 7) cuts hair
to 7/8" (22mm).
• Left ear attachment comb lightly tapers
over left ear.
• Right ear attachment comb lightly tapers
over right ear.
Attach combs by
holding them teeth
up, then snapping
onto the bottom of
the clipper blade.
To remove comb
attachments, place
index finger and
thumb as illus-
trated; then pull
out and up.
NOTE: Never push or shove the clipper
through the hair to make it move more
quickly. Professional experience shows
that the clipper works most efficiently
when it cuts through the hair at its
own speed.
To begin cutting hair:
1. The hair should be
combed in its natural
direction.
2. Using the longest
comb attachment, trim
sides from the bottom
upward. Hold clipper
lightly against the hair
with teeth of the comb
attachment pointing
up ward, yet flat against
the head. Gradually lift
the clipper upward and
outward through the hair,
trimming just a little at
a time.
Repeat around sides and
back of head.
If you want hair to be
even shorter:
A) Apply more pressure
to the head with the comb attachment that is
in place. This takes a little practice, of course.
OR
B) Just switch to a shorter comb attachment.
Remember, its better to
leave too much hair than
too little. For longer hair on
top, use the barber comb
and lift hair on the top of
the head, cutting over the
comb. Or hold the hair
between the fingers and
cut to desired length. Always working from
the front to the back of the head, gradually
cut the hair shorter by reducing the space
between the comb or fingers and the head.
Comb often to check for uneven strands,
and to get rid of trimmed hair.
OUTLINING
Outlining requires no
attachments. Comb hair into
the desired style. Position
the clipper between the
sideburns and the ear (see
illustration), making sure the
corner edge of the blade is
against the hairline. With the
outline of the hair as your
guide, slowly move the clip-
per over, around and behind
the ears. For the back of
the neck and the sideburns,
hold the clipper upside down (see illustration)
and, holding it against the skin at the length
desired, move the clipper downward.
STOP. COMB. CHECK.
For best results, do as the professionals do:
Comb hair often, and check clipping results
as you comb. This way you avoid uneven
sides, bangs, neckline, etc.
SHORT CUTS TO PERFECT
FLATTOPS, CREW CUTS, ETC.
Always cut from the back of the neck to
the crown, using the longest comb setting.
Hold the comb attachment flat against the
head and slowly move the clipper up through
the hair. Use the same technique for the
sides, cutting from the bottom to the
upper side of the head.
For the front to the crown,
cut the hair against the
direction in which it grows.
Then even it up with
the sides.
For a flattop, use the
flat comb, not the comb
attachment. Just cut hair
on top of the head over flat
comb (see illustration).
USER MAINTENANCE
CARE OF YOUR CLIPPERS
Detachable Blade Set
This clipper comes with a detachable blade set.
To remove the blades,
follow these steps:
1. Hold the front part of the
clipper with your thumb
pressing on the blade and
place another hand against
the blade (see Fig. 1)
2. When pressing the
blade forward, the blade is
detached (see Fig. 2)
TO REPLACE BLADE:
1. Set the Taper Control
Button to lowest position
“1” (see Fig. 3)
2. Place the blade onto the
clipper body by inserting
the “Blade Tongue” down
below the “Lock Tap” (see
Fig. 4)
3. Snap the blade down into
position. The blade is now
fixed onto the clipper body
(see Fig. 5)
ADJUSTABLE TAPER CONTROL
Unlike levers on professional clippers that
are positioned on the side, the Conair taper
control is positioned at the back of the unit.
The taper level functions for both the clipper
and trimmer blade, so you can hold the
clipper in your hand and adjust the lever
at the same time...while you’re clipping/
trimming. This taper control eliminates the
need in some situations for an attachment
comb, because it lets you gradually adjust
the closeness of the cut. For the closest cut
and the shortest hair, push taper control up
as far as it will go to position #5. To increase
cutting length, slowly push control down.
If you push to the lowest position #1, it will
leave hair about the same length as the short
attachment comb.
Because a different cutting edge is used in
each setting, the taper lever lengthens the life
of your blades. Packed-in hair can slow down
any clipper. To remove it without removing the
blades, take your cleaning brush and brush
the hair from the blades. If you do this after
every clipping, especially with heavy hair
cutting, the blades should remain free of cut
hair. If clipper stops cutting and this action
doesn’t help, try loosening the blades to
remove the hair.
Any other servicing should be performed by
an authorized service representative. The
appliance has no user-serviceable parts. The
product is for household use (see note).
If clipper stops cutting, check to see if there
is a clump of hair lodged between the blades.
If that is the problem, unplug the clipper and
then loosen the blades to remove the hair.
If the clipper stops cutting, but does not stop
running, you will need to check the blades.
For new blades, send check or money order
for $6.50, which includes postage and han-
dling, to:
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
NOTE: Never pull on the clipper cord. Never
twist or wrap the cord around the clipper. Lay
it flat with the cord coiled up when not in use.
STORAGE: When not in use, your clipper
should be disconnected, allowed to cool and
stored in a safe, dry location, out of reach of
children.
Any other servicing should be performed by
an authorized service representative.
This appliance has no user-serviceable parts.
This appliance is for household use.
Stainless steel,
self-sharpening
blades
On/Off
switch
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water
are a dangerous combination. But did you
know that an electric appliance is still
electrically live even if the switch is off? If
the plug is in, the power is on. So when you
are not using your appliances, keep them
unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED FIVE-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 60 months from the date of
purchase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the
defective product to the service center listed on back,
together with your purchase receipt and $3.00 for
postage and handling. California residents need only
provide proof of purchase and should call
1-800-3-CONAIR for shipping instructions. In the
absence of a purchase receipt, the warranty period
shall be 60 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE 60-MONTH DURATION OF THIS
WRITTEN, LIMITED WARRANTY. Some states do not
allow limitations on how long an implied warranty
lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS
OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. Some states do not allow the exclusion
or limitation of special, incidental, or consequential
damages, so the above limitation may not apply
to you.
This warranty gives you specific legal rights,
and you may also have other rights, which vary from
state to state.
Model
HC2000-BLD
Model HC OIL
Model SC-1
Model HC2000-3 Model HC2000-4
Model HC-1
Please register this product at
www.conair.com/registration
©2018 Conair Corporation
Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
18PG054025
IB-15711
HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM
Pricing in effect through December 31, 2020. Orders postmarked after this date
will be accepted, and the customer will be notified if pricing has changed.
CUT HERE
Mail to:
Conair Corporation
Service Department
150 Milford Road
East Windsor, NJ 08520-9730
Enclose check or money order made payable to Conair. (We cannot accept cash, stamps
or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax.
Minimum order of $10.00 or a $2.00 handling charge will be added to order.
All prices include handling and return postage. Prices are subject to change without
notice. Prices are valid only for shipments within the continental United States.
Please allow 4 6 weeks for delivery.
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. Box.
NAME _________________________________________________________________________________________________
ADDRESS APT. ___________________________________________ ______________________________________________
CITY ________________________________ ________________________________________________STATE _________ ZIP
TELEPHONE ( ) _____________________________________________________________
(We call only if we have a question about your order.)
For information on other Conair
® haircut kit parts call: 1-800-3-CONAIR.
Subtotal
Sales Tax*
TOTAL
Clipper Blade HC2000-BLD $6.50
4 Comb Attachments: 1/8", 1/4", 3/8", 1/2"
HC2000-4 $5.00
3 Comb Attachments: 5/8
"
, 3/4
"
, 7/8
"
HC2000-3 $5.00
Lubricating Oil (pkg. of 3 tubes) HC OIL $1.00
Barber Scissors SC-1 $2.00
Blade Guard HC-1 $1.00
ITEM PART # PRICE QUANTITY AMOUNT


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: HC2000

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HC2000 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024