Conair HC200GB Manual

Conair Ikke kategoriseret HC200GB

Læs nedenfor 📖 manual på dansk for Conair HC200GB (6 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/6

Before you start:

1. Inspect your clipper. Make sure it’s free of

hair and dirt, properly oiled, and running

smoothly.

PIECE

Haircut kit

Instructions for

Care and Use

MODEL HC200ACS

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances,

especially when children are present, basic

safety precautions should always be taken,

including the following:

READ ALL INSTRUCTIONS

BEFORE USING

KEEP AWAY FROM WATER

DANGER- any appliance is

electrically live, even when the switch is off.

To reduce the risk of death or injury by

electric shock:

1. Unplug this appliance before cleaning.

2. Do not place or store appliance where it

can fall or be pulled into a tub or sink.

3. Do not use while bathing or in a shower.

4. Do not place in, or drop into water or other

liquid.

5. Do not reach for an appliance that has fallen

into water. Unplug immediately.

6. Always unplug this appliance from electrical

outlet immediately after using.

DO NOT REACH

INTO THE WATER

WARNING- To reduce the risk of

burns, electric shock, fire, or injury to persons:

1. This appliance should never be left unat-

tended when plugged in. Do not pull, twist,

or wrap line cord around appliance.

2. This appliance should not be used by, on,

or near children or individuals with certain

disabilities.

3. Use this appliance only for its intended

purpose as described in this manual. Do not

use attachments not recommended by the

manufacturer. Do not use an extension cord

to operate this appliance.

4. Never operate this appliance if it has a dam-

aged cord or plug, or if it is not working proper-

ly, if it has been dropped or damaged, or

dropped into water. Return the appliance to a

service center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any

opening on this appliance.

7. Do not place appliance on any surface

while it is operating.

8. Do not use this appliance with a

damaged or broken comb or with teeth missing

from the blades as injury may occur. Before

use, make certain blades are aligned properly.

(See “Care of your Clippers”)

9. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

10. Never operate the appliance with the air

openings blocks or while on a soft surface, such

as a bed or couch, where the air

openings may be blocked. Keep the air

openings free of lint, hair, and the like.

11. Always attach plug to appliance first, then

to outlet. To disconnect, turn all controls to

“OFF” then remove plug from outlet.

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

This appliance is intended for household use.

Use on Alternating Current 60 hertz

only. This appliance has a polarized plug

(one blade is wider than the other). As a

safety feature, this plug will fit in the outlet

only one way. If the plug does not fit fully in

the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician to install the

proper outlet. Do not attempt to defeat this

safety feature.

Your new Conair®haircut kit has everything

you need to achieve professional haircuts at

home. It features a powerful clipper with

adjustable taper control and high carbon

steel blades for cutting precision. Also

included are 9 attachment combs (1/8”, 1/4”,

3/8”, 1/2”, 5/8”, 3/4*”, 7/8” for different hair

lengths, left and right ear combs), barber

scissors, 1 styling comb with angled teeth,

barber cape, storage case, a barber comb

with straight teeth, and 2 styling clips to

assist you in cutting longer hair styles. A 28

minute step-by-step How-to DVD filled with

styling tips and techniques. It also comes

with lubricating oil, a cleaning brush and a

blade guard for easy maintenance of the clip-

per blades.

THE CONAIR GUIDE

TO CUTTING HAIR AT HOME

2. Place a towel around the neck of the person.

3. Seat the person so that his or her head is at

your eye level.This gives you greater visibility and

control.

4. First, comb hair until it’s tangle-free. Then hold

clipper in a comfortable grip. Now you’re ready

to cut.

MEDIUM TO LONG CUT

To begin with, cut only a small amount of hair

until you become used to the length each attach-

ment leaves the hair. Try the longest attachment

on the clipper first. If you want a shorter cut, you

can then use shorter combs.

• Short attachment comb (number 1) cuts hair

to 1/8”.

• Medium-Short attachment comb (number 2)

cuts hair to 1/4”.

• Medium-Long attachment comb (number 3)

cuts hair to 3/8”.

• Long attachment comb (number 4) cuts hair

to 1/2”.

• Long attachment comb (number 5) cuts hair

to 5/8”

• Long attachment comb (number 6) cuts hair

to 3/4”

• Long attachment comb (number 7) cuts hair

to 7/8”

• Left ear attachment comb lightly tapers over

left ear.

• Right ear attachment comb lightly tapers over

right ear.

Attach combs by

holding them teeth

up, then snapping

onto the bottom of

the clipper blade.

To remove comb

a t t a c h m e n t s ,

place index finger

and thumb as

illustrated; then

pull out and up.

NOTE: Never push or shove the clipper

through the hair to make it move

more quickly. Professional experience

shows that the clipper works most

efficiently when it cuts through the

hair at its own speed.

To begin cutting hair:

1. The hair should be combed in its

natural direction.

2. Using the largest attachment comb, trim

sides from the bottom upward. Hold clipper

lightly against the hair

with teeth of the

attachment comb

pointing upward, yet

flat against the head.

Gradually lift the clip-

per upward and out-

ward through the hair,

trimming just a little at

a time.

Repeat around sides

and back of head.

If you want hair to be

even shorter:

A) Apply more

pressure to the head

with the attachment

comb that is in place.

This takes a little

practice, of course. OR

B) Just switch to a

shorter attachment

comb.

Remember, it’s better to

leave too much hair than

too little. For longer hair

on top, use the barber

comb and lift hair on the

top of the head, cutting

over the comb. Or hold

the hair between the fin-

gers and cut to desired

length.Always working

from the front to the

back of the head, gradually cut the hair short-

er by reducing the space between the comb

or fingers and the head. Comb often to check

for uneven strands, and to get rid of trimmed

hair.

OUTLINING:

Outlining requires no attachments. Comb

hair into the desired style. Position the

clipper between the sideburns and the ear

(see below), making sure the corner edge

of the blade is against the hairline. With

the outline of the hair as your guide,

slowly move the clipper over, around and

behind the ears. For the back of the neck

and the sideburns, hold the clipper upside

down (see above) and, holding it against

the skin at the length desired, move the

clipper downward.

STOP. COMB. CHECK.

For best results, do as the professionals

do: comb hair often, and check clipping

results as you comb. This way you avoid

uneven sides, bangs, neckline, etc.

SHORT CUTS TO PERFECT

FLAT TOPS, CREW CUTS, ETC.

Always cut from the back of the neck to the

crown, using the longest comb setting.

Hold the comb attachment flat against the

head and slowly move the clipper up

through the hair. Use the same technique

for the sides, cutting from the bottom to

the upper side of the head.

For the front to the crown, cut the hair

against the direction in which it grows.

Then even it up with the sides.

For a flat top, use the flat comb, not the

attachment comb. Just cut hair on top of

the head over flat comb. (see above).

To taper hair down to the neckline, use

attachment comb #1. Comb hair and

check for uneven spots. Outline sideburns

and neck areas (see “Outlining”).

USER-MAINTENANCE

INSTRUCTIONS

CARE OF YOUR CLIPPERS

IF YOU DETERMINE THAT BLADE

ALIGNMENT IS INCORRECT:

Conair®hair clippers are carefully inspected

to insure that the blades are in perfect

alignment. Of course you will need to

realign the blades after removal for cleaning

or replacement, or if they should be

knocked out of alignment. How can you

tell if blades need realigning? Simply

match them up, point for point, to

conform with FIG. 1 below:

FIG. 1

To prevent the clipper from contacting the

skin or cutting too closely, make certain

that the end top blade teeth are 1/32” to

1/16” back from bottom blade.

To Align Blades:

1. Add two or three drops

of Conair Lubricating Oil

(included).

2.Turn clipper on for a

minute to disperse oil

evenly over blades, then FIG. 2

turn off.

3. Unplug clipper and slightly loosen

screws. (See FIG. 2)

4. Position the extreme left-hand tooth of

the top blade so that it either covers or

appears on the left of the first small tooth

on the bottom blade.

5. Make sure that the big tooth on the

bottom blade touches the extreme right hand

tooth of the top blade.

SPECIAL OIL

To maintain the blades of your Conair

clipper, oil them after every three or four

haircuts. Gently place a few drops of oil on

the teeth of the blades, using the

special Conair oil included with your set.

Turn the clipper on for a minute, then turn

off. This light, natural oil was formulated

specifically for the Conair high-speed

clipper. Because it is the right oil to use, it

will not slow down the blades. Never use

any other product. There is no substitute

for Conair oil.

ADJUSTABLE TAPER LEVER

Just like professional clippers, the

Conair taper lever is positioned at

your thumb. You can hold the clipper

in your hand and adjust the lever at the

same time...while you’re clipping.

This taper lever eliminates the need for an

attachment comb because it lets you

gradually adjust the closeness of the cut.

For the closest cut and the shortest hair,

push taper lever up as far as it will go.

To increase cutting length, slowly push

lever down. If you push to the lowest

position, it will leave hair about the same

length as the short attachment.

Because a different cutting edge is used in

each setting, the taper lever lengthens the life

of your blades.

Packed-in hair can slow down any clipper.

To remove hair without removing the

blades, do what the professionals do:

keeping the clipper on, quickly push the

taper lever back and forth from “close” to

“longer” cut a few times.

If you do this after every clipping, especially

with heavy hair cutting, the blades should

remain free of cut hair.

Longer

Cut

Close Cut

If clipper stops cutting and this action doesn’t

help, check the blades. If they’ve become dull,

replace them or return them to a Conair ser-

vice center. We’ll be glad to

sharpen them for you. For new blades, send

check or money order for $6.50 (see order

blank) which includes postage and

handling(If $10 minimum is met) to:

Conair Corporation

150 Milford Rd.

East Windsor, NJ 08520

NOTE: Never pull on the clipper cord.

Never twist or wrap the cord around the

clipper. Lay it flat with the cord coiled up

when not in use.

Bottom Blade

Adjustable

Taper Lever

Top Blade

WARNING:

IF YOU THINK

THE POWER IS OFF

WHEN THE SWITCH

IS OFF,

YOU'RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water

are a dangerous combination. But did you

know that an electric appliance is still

electrically alive even if the switch is off?

If the plug is in, the power is on. So when

you are not using your appliances, keep

them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

Public Service ad from Association of Home Appliance

Manufacturers and Underwriters Laboratories, Inc.

LIMITED FIVE YEAR WARRANTY

Conair will repair or replace (at our option) your unit

free of charge for 60 months from the date of pur-

chase if the appliance is defective in workmanship or

materials.

To obtain service under this warranty, return the defec-

tive product to the service center listed below that is

nearest you, together with your purchase receipt and

$3.00 for postage and handling. California residents need

only provide proof of purchase and should call 1-800-

366-0937 for shipping instructions. In the absence of a

purchase receipt, the warranty period shall be 60 months

from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIA-

BILITIES, INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, SHALL BE

LIMITED IN DURATION TO THE 60 MONTH DURA-

TION OF THIS WRITTEN, LIMITED WARRANTY.

Some states do not allow limitations on how long an

implied warranty lasts, so the above limitations may

not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAM-

AGES FOR BREACH OF THIS OR ANY OTHER WAR-

RANTY, EXPRESS OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or limitation of

special, incidental, or consequential damages, so the

above limitation may not apply to you.

This warranty gives you specific legal rights, and you

may also have other rights, which vary from state to

state.

SERVICE CENTER:

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

IB-7265

Once again, thanks for buying a

Conair product.

Your Conair®clipper blades are made of

high carbon stainless steel. They are

engineered for precise, professional results.

If blades feel like they are pulling or grab-

bing hair, it means they are losing their

sharpness and should be replaced as soon

as possible.

Attachment combs should also be replaced

if they are lost or broken. It is easier to cut

hair with the accuracy of a pro when the

necessary tools are at your fingertips.

Conair makes a variety of accessories

for different haircut kits. If your haircut kit

does not include them, you may want to

consider adding them to your professional

haircutting tools.

Left and right ear attachment combs

provide effortless, precise cutting around the

ears. Styling clips hold hair in place when you

are sectioning hair. A styling comb makes it

easy to taper or cut hair at an angle. A barber

cape ensures a comfortable and neat haircut

and a convenient storage pouch keeps all your

essentials in one place.

Last but not least, an easy-to-follow 30-

minute “Haircuts at Home” video is

available. It demonstrates basic haircutting

techniques and follows four popular

haircuts step by step. It will give you the

confidence and instruction you need to give

great looking haircuts to every member of

your family.

PT1 Mighty Mini 15 Piece Clipper Kit

Powerful DC motor

makes this unique,

lightweight clipper /

trimmer a versatile

cutting instrument as

it can also be used for

detailing and bikini

line trimming.

HC90 10 Piece Haircut Kit

Powerful magnetic

motor clipper with

stainless steel blades

and 4 attachment

combs.

MN253 Cobra Trimmer

3-in-1 Deluxe,

rechargeable detail-

er. 3 interchangeable

heads include a full

size trimmer, shaver

and nose and ear

attachment for all

facial fashions. *Not

recommended for

thick beards.

Model COMB-10

Model COMB-11

Model COMB-13

Model COMB-12

Model HCNB-1 Model CAPE-1 Model HC OIL

Model HC VIDEO

Model SC- 1

Model BLD- 8

Model HC- 1 Model CLP- 1

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM

Pricing in effect through June 1, 2008. Orders postmarked after this date

will be accepted, and the customer will be notified if pricing has changed.

CUT HERE

COMB-10 $5.00

Set of 4 Attachment Combs:1/8”, 1/4”, 3/8”, 1/2”.

Fits all clippers (HC200, HC220, HC240, HC102

HC300, HC318, HC414, HC275, HC222)

Set of 2 Attachment Combs: left ear and right ear. Fits all clippers (see COMB-10).except HC222 COMB-11 $1.75

1" Comb fits all clippers COMB-12 $1.75

3 attachment combs 5/8", 3/4", 7/8". Fits all clippers COMB-13 $5.00

Neck Brush HCNB-1 $1.50

Deluxe Black Vinyl Cape with Velcro Collar CAPE-1 $5.00

Lubricating Oil (pkg. of 3 tubes) HC OIL $2.00

30 Minute Haircut Video HC VIDEO $8.95

Barber Scissors SC-1 $2.00

Blade Set for HC200 Detent Clipper BLD-8 $6.50

Blade Guard HC-1 $1.00

Styling Clips (set of 3) CLP-1 $1.50

ITEM PART # PRICE QUANTITY AMOUNT

Subtotal

*Sales Tax

TOTAL

Prices are valid only for shipments within the Continental United States. Please allow 4-6 weeks for delivery.

To avoid delays, please print clearly.

We must have a street address, as UPS cannot deliver to a P.O. box.

NAME____________________________________________________________________________

ADDRESS___________________________________________________ APT. ________________

CITY _______________________________________________STATE _______ ZIP ____________

TELEPHONE ( ) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

(We call only if we have a question about your order.)

For information on other Conair

®haircut kit parts call: 1-800-3-CONAIR.

Mail to:

Conair Corporation

Service Department

150 Milford Road

East Windsor, NJ 08520-9730

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D. orders.) CT, IL, AZ, and PA res-

idents should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be added to order.

All prices include handling and return post age. notice. Price s are su bj e ct to change without

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	HC200GB

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HC200GB stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair NPTCCA01 Manual

10 December 2024

Conair True Glow PB8NPRF Manual

10 December 2024

Conair NPTCCA02 Manual

10 December 2024

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg KIT6PX Manual

23 December 2024

Smeg KIT6CX Manual

23 December 2024

Smeg GTA-6 Manual

23 December 2024

Lucide Casper i 79166/19/12 Manual

23 December 2024

Lucide Merlina 78193/30/66 Manual

23 December 2024

Lucide Pippa 77583/81/30 Manual

23 December 2024

Lucide Pia 45380/04/30 Manual

23 December 2024

Lucide Pia 45280/01/30 Manual

23 December 2024

Lucide Anaka 45179/03/30 Manual

23 December 2024

Lucide Zych 45156/01/97 Manual

23 December 2024